Re: [PATCH 1/8] dt-bindings: pmic: Document Hi655x pmic driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Wed, 30 Sep 2015, Fei Wang wrote:

> Document the new compatible for Hisilicon Hi655x pmic driver.

s/pmic/PMIC/

> Signed-off-by: Fei Wang <w.f@xxxxxxxxxx>
> ---
>  .../devicetree/bindings/mfd/hisilicon,hi655x.txt   |   80 ++++++++++++++++++++
>  1 file changed, 80 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt
> 
> diff --git a/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt
> new file mode 100644
> index 0000000..17bd8ca
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/hisilicon,hi655x.txt
> @@ -0,0 +1,80 @@
> +Hisilicon hi655x Power Management Integrated Circuit (PMIC)
> +
> +hi655x consists of a large and varied group of sub-devices:
> +
> +Device			 Supply Names	 Description
> +------			 ------------	 -----------
> +hi655x-powerkey		:		: Powerkey
> +hi655x-regulator-pmic	:		: Regulators
> +hi655x-usbvbus		:		: USB plug detection
> +hi655x-pmu-rtc		:		: RTC
> +hi655x-coul		:		: Coulomb

As Mark said, these all need documentation.

> +Required properties:
> +- compatible : Should be "hisilicon,hi655x-pmic-driver"
> +- reg: Base address of PMIC on hi6220 soc
> +- #interrupt-cells: Should be 2, is the local IRQ number for hi655x.
> +- interrupt-controller: hi655x has internal IRQs (has own IRQ domain).
> +- pmu_irq_gpio: should be &gpio_pmu_irq_n, is the IRQ gpio of hi655x.

Better if you tab these out, like:

- compatible		: Should be "hisilicon,hi655x-pmic-driver"
- reg			: Base address of PMIC on hi6220 soc

Etc ...

> +Example:
> +	pmic: pmic@F8000000 {

s/F/f/

> +                compatible = "hisilicon,hi655x-pmic-driver";
> +                reg = <0x0 0xF8000000 0x0 0x1000>;

Small a => f please.

> +                #interrupt-cells = <2>;
> +                interrupt-controller;
> +                pmu_irq_gpio = <&gpio_pmu_irq_n>;

This should be <name>-gpios.

No underscores please.

> +                status = "ok";

Use "okay" instead.

> +                ponkey:ponkey@b1{

White space issues here.

Where is the 'reg' property?

> +                        compatible = "hisilicon,hi655x-powerkey";
> +                        interrupt-parent = <&pmic>;
> +                        interrupts = <6 0>, <5 0>, <4 0>;

Use #defines (same goes for all below).

> +                        interrupt-names = "down", "up", "hold 1s";

White space in a name seems wrong to me.

> +                };
> +
> +                coul: coul@1 {

What is @1?

Is this label used?

> +                        compatible = "hisilicon,hi655x-coul";
> +                        interrupt-parent = <&pmic>;
> +                        interrupts = <24 0>, <25 0>, <26 0>, <27 0>;
> +                        interrupt-names = "cl_int_i", "cl_out_i", "cl_in_i", "vbat_int_i";
> +                        battery_product_index = <0>;

Documentation?  It doesn't look like a generic propriety either, so
should be have a vendor prefix.

> +                        status = "ok";

"okay"

> +                };
> +
> +                rtc: rtc@1 {

Is this label used?

> +                        compatible = "hisilicon,hi655x-pmu-rtc";
> +                        interrupt-parent = <&pmic>;
> +                        interrupts = <20 0>;
> +                        interrupt-names = "hi655x_pmu_rtc";
> +                        board_id = <1>;

What's this?  No IDs in DT please.

> +                };
> +
> +                usbvbus:usbvbus@b2{

Whitespace.

'reg'?

> +                        compatible = "hisilicon,hi655x-usbvbus";
> +                        interrupt-parent = <&pmic>;
> +                        interrupts = <9 0>, <8 0>;
> +                        interrupt-names = "connect", "disconnect";
> +                };
> +
> +		ldo2: regulator@a21 {

Tabbing seems wrong here.

> +                        compatible = "hisilicon,hi655x-regulator-pmic";
> +                        regulator-name = "ldo2";
> +                        regulator-min-microvolt = <2500000>;
> +                        regulator-max-microvolt = <3200000>;
> +                        hisilicon,valid-modes-mask = <0x02>;
> +                        hisilicon,valid-ops-mask = <0x01d>;
> +                        hisilicon,initial-mode = <0x02>;
> +                        hisilicon,regulator-type = <0x01>;
> +
> +                        hisilicon,off-on-delay = <120>;
> +                        hisilicon,ctrl-regs = <0x029 0x02a 0x02b>;
> +                        hisilicon,ctrl-data = <0x1 0x1>;
> +                        hisilicon,vset-regs = <0x072>;
> +                        hisilicon,vset-data = <0 0x3>;
> +                        hisilicon,regulator-n-vol = <8>;
> +                        hisilicon,vset-table = <2500000>,<2600000>,<2700000>,<2800000>,<2900000>,<3000000>,<3100000>,<3200000>;

Whitespace.

> +                        hisilicon,num_consumer_supplies = <1>;
> +                        hisilicon,consumer-supplies = "sensor_analog";


All of these vendor properties need documenting and signing of by Mark
(the Regulator Maintainer).

> +                };
> +	};

-- 
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux