On 01/09/15 12:45, Martin Kepplinger wrote:
> This adds the freefall / motion interrupt source definitions to the driver.
> It is used in this series' next patch, for chips that don't support the
> transient interrupt source.
>
> Signed-off-by: Martin Kepplinger <martin.kepplinger@xxxxxxxxxxxxxxxxxxxxx>
> Signed-off-by: Christoph Muellner <christoph.muellner@xxxxxxxxxxxxxxxxxxxxx>
Applied.
> ---
> drivers/iio/accel/mma8452.c | 44 ++++++++++++++++++++++++++++++++++++--------
> 1 file changed, 36 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
> index 7b2ab17..6b1a862 100644
> --- a/drivers/iio/accel/mma8452.c
> +++ b/drivers/iio/accel/mma8452.c
> @@ -42,6 +42,16 @@
> #define MMA8452_DATA_CFG_HPF_MASK BIT(4)
> #define MMA8452_HP_FILTER_CUTOFF 0x0f
> #define MMA8452_HP_FILTER_CUTOFF_SEL_MASK GENMASK(1, 0)
> +#define MMA8452_FF_MT_CFG 0x15
> +#define MMA8452_FF_MT_CFG_OAE BIT(6)
> +#define MMA8452_FF_MT_CFG_ELE BIT(7)
> +#define MMA8452_FF_MT_SRC 0x16
> +#define MMA8452_FF_MT_SRC_XHE BIT(1)
> +#define MMA8452_FF_MT_SRC_YHE BIT(3)
> +#define MMA8452_FF_MT_SRC_ZHE BIT(5)
> +#define MMA8452_FF_MT_THS 0x17
> +#define MMA8452_FF_MT_THS_MASK 0x7f
> +#define MMA8452_FF_MT_COUNT 0x18
> #define MMA8452_TRANSIENT_CFG 0x1d
> #define MMA8452_TRANSIENT_CFG_HPF_BYP BIT(0)
> #define MMA8452_TRANSIENT_CFG_CHAN(chan) BIT(chan + 1)
> @@ -69,6 +79,7 @@
> #define MMA8452_MAX_REG 0x31
>
> #define MMA8452_INT_DRDY BIT(0)
> +#define MMA8452_INT_FF_MT BIT(2)
> #define MMA8452_INT_TRANS BIT(5)
>
> #define MMA8452_DEVICE_ID 0x2a
> @@ -613,7 +624,8 @@ static int mma8452_write_event_config(struct iio_dev *indio_dev,
> else
> val &= ~BIT(chan->scan_index + chip->ev_cfg_chan_shift);
>
> - val |= MMA8452_TRANSIENT_CFG_ELE;
> + val |= chip->ev_cfg_ele;
> + val |= MMA8452_FF_MT_CFG_OAE;
>
> return mma8452_change_config(data, chip->ev_cfg, val);
> }
> @@ -654,6 +666,7 @@ static irqreturn_t mma8452_interrupt(int irq, void *p)
> {
> struct iio_dev *indio_dev = p;
> struct mma8452_data *data = iio_priv(indio_dev);
> + const struct mma_chip_info *chip = data->chip_info;
> int ret = IRQ_NONE;
> int src;
>
> @@ -666,7 +679,10 @@ static irqreturn_t mma8452_interrupt(int irq, void *p)
> ret = IRQ_HANDLED;
> }
>
> - if (src & MMA8452_INT_TRANS) {
> + if ((src & MMA8452_INT_TRANS &&
> + chip->ev_src == MMA8452_TRANSIENT_SRC) ||
> + (src & MMA8452_INT_FF_MT &&
> + chip->ev_src == MMA8452_FF_MT_SRC)) {
> mma8452_transient_interrupt(indio_dev);
> ret = IRQ_HANDLED;
> }
> @@ -728,6 +744,16 @@ static const struct iio_event_spec mma8452_transient_event[] = {
> },
> };
>
> +static const struct iio_event_spec mma8452_motion_event[] = {
> + {
> + .type = IIO_EV_TYPE_MAG,
> + .dir = IIO_EV_DIR_RISING,
> + .mask_separate = BIT(IIO_EV_INFO_ENABLE),
> + .mask_shared_by_type = BIT(IIO_EV_INFO_VALUE) |
> + BIT(IIO_EV_INFO_PERIOD)
> + },
> +};
> +
> /*
> * Threshold is configured in fixed 8G/127 steps regardless of
> * currently selected scale for measurement.
> @@ -1013,13 +1039,15 @@ static int mma8452_probe(struct i2c_client *client,
>
> if (client->irq) {
> /*
> - * Although we enable the transient interrupt source once and
> - * for all here the transient event detection itself is not
> - * enabled until userspace asks for it by
> - * mma8452_write_event_config()
> + * Although we enable the interrupt sources once and for
> + * all here the event detection itself is not enabled until
> + * userspace asks for it by mma8452_write_event_config()
> */
> - int supported_interrupts = MMA8452_INT_DRDY | MMA8452_INT_TRANS;
> - int enabled_interrupts = MMA8452_INT_TRANS;
> + int supported_interrupts = MMA8452_INT_DRDY |
> + MMA8452_INT_TRANS |
> + MMA8452_INT_FF_MT;
> + int enabled_interrupts = MMA8452_INT_TRANS |
> + MMA8452_INT_FF_MT;
>
> /* Assume wired to INT1 pin */
> ret = i2c_smbus_write_byte_data(client,
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
