Extend the bq24257 charger's device tree documentation to cover the bq24250 and bq24251 devices as well feature additions. Signed-off-by: Andreas Dannenberg <dannenberg@xxxxxx> --- .../devicetree/bindings/power/bq24257.txt | 59 ++++++++++++++++++++-- 1 file changed, 54 insertions(+), 5 deletions(-) diff --git a/Documentation/devicetree/bindings/power/bq24257.txt b/Documentation/devicetree/bindings/power/bq24257.txt index 5c9d394..4a88c96 100644 --- a/Documentation/devicetree/bindings/power/bq24257.txt +++ b/Documentation/devicetree/bindings/power/bq24257.txt @@ -1,21 +1,70 @@ -Binding for TI bq24257 Li-Ion Charger +Binding for TI bq24250/bq24251/bq24257 Li-Ion Charger Required properties: - compatible: Should contain one of the following: + * "ti,bq24250" + * "ti,bq24251" * "ti,bq24257" -- reg: integer, i2c address of the device. +- reg: integer, i2c address of the device. +- stat-gpios: GPIO used for the devices STAT_IN pin. Alternatively the pin can + also be defined through the standard interrupt definition properties (see + optional properties section below). Only use one method. - ti,battery-regulation-voltage: integer, maximum charging voltage in uV. -- ti,charge-current: integer, maximum charging current in uA. -- ti,termination-current: integer, charge will be terminated when current in - constant-voltage phase drops below this value (in uA). +- ti,charge-current: integer, maximum charging current in uA. +- ti,termination-current: integer, charge will be terminated when current in + constant-voltage phase drops below this value (in uA). + +Optional properties: +- pg-gpios: GPIO used for connecting the bq2425x device PG (Power Good) pin. + This pin is not available on all devices however it should be used if + possible as this is the recommended way to obtain the charger's input PG + state. If this pin is not specified a software-based approach for PG + detection is used. +- ti,current-limit: The maximum current to be drawn from the charger's input + (in uA). If this property is not specified a USB D+/D- signal based charger + type detection is used (if available) and the input limit current is set + accordingly. If the D+/D- based detection is not available on a given device + a default of 500,000 is used (=500mA). +- ti,ovp-voltage: Configures the over voltage protection voltage (in uV). If + not specified a default of 6,5000,000 (=6.5V) is used. +- ti,in-dpm-voltage: Configures the threshold input voltage for the dynamic + power path management (in uV). If not specified a default of 4,360,000 + (=4.36V) is used. +- ti,safety-timer-2x-enable: If this property is set to 1 the device's safety + timer is extended (slowed down) by a factor of two. Setting this property + to 0 or not providing it will leave the safety timer at its default + setting. +- interrupt-parent: Should be the phandle for the interrupt controller. Use in + conjunction with "interrupts" and only in case "stat-gpios" is not used. +- interrupts: Interrupt mapping for GPIO IRQ (configure for both edges). Use in + conjunction with "interrupt-parent" and only in case "stat-gpios" is not + used. Example: bq24257 { compatible = "ti,bq24257"; reg = <0x6a>; + stat-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>; + pg-gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; ti,battery-regulation-voltage = <4200000>; ti,charge-current = <1000000>; ti,termination-current = <50000>; }; + +Example: + +bq24250 { + compatible = "ti,bq24250"; + reg = <0x6a>; + interrupt-parent = <&gpio1>; + interrupts = <16 IRQ_TYPE_EDGE_BOTH>; + + ti,battery-regulation-voltage = <4200000>; + ti,charge-current = <500000>; + ti,termination-current = <50000>; + ti,current-limit = <900000>; + ti,ovp-voltage = <9500000>; + ti,in-dpm-voltage = <4440000>; +}; -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html