Hi Moritz,
Thanks. I will take care of these suggestions in next version
Regards,
Punnaiah
On Fri, Aug 21, 2015 at 10:12 PM, Moritz Fischer
<moritz.fischer@xxxxxxxxx> wrote:
> Hi all,
>
> sorry for HTML mail spam last night ... couple of nits below
>
> On Wed, Aug 5, 2015 at 8:19 PM, Punnaiah Choudary Kalluri
> <punnaiah.choudary.kalluri@xxxxxxxxxx> wrote:
>> Device-tree binding documentation for Xilinx zynqmp dma engine used in
>> Zynq UltraScale+ MPSoC.
>>
>> Signed-off-by: Punnaiah Choudary Kalluri <punnaia@xxxxxxxxxx>
>> ---
>> Changes in v4:
>> - None
>> Changes in v3:
>> - None
>> Changes in v2:
>> - None
>> ---
>> .../devicetree/bindings/dma/xilinx/zynqmp_dma.txt | 61 ++++++++++++++++++++
>> 1 files changed, 61 insertions(+), 0 deletions(-)
>> create mode 100644 Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt
>>
>> diff --git a/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt
>> new file mode 100644
>> index 0000000..e4f92b9
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/dma/xilinx/zynqmp_dma.txt
>> @@ -0,0 +1,61 @@
>> +Xilinx ZynqMP DMA engine, it does support memory to memory transfers,
>> +memory to device and device to memory transfers. It also has flow
>> +control and rate control support for slave/peripheral dma access.
>
> How about: The Xilinx ZynqMP DMA engine does support memory to memory transfers,
> memory to device and device to memory transfers. It also has flow
> control and rate control
> support for slave / peripheral DMA access.
>> +
>> +Required properties:
>> +- compatible: Should be "xlnx,zynqmp-dma-1.0"
>> +- #dma-cells: Should be <1>, a single cell holding a line request number
>> +- reg: Memory map for module access
>> +- interrupt-parent: Interrupt controller the interrupt is routed through
>> +- interrupts: Should contain DMA channel interrupt
>> +- xlnx,bus-width: AXI buswidth in bits. Should contain 128 or 64
>> +
>> +Optional properties:
>> +- xlnx,include-sg: Indicates the controller to operate in simple or scatter
>> + gather dma mode
> s/dma/DMA
>> +- xlnx,ratectrl: Scheduling interval in terms of clock cycles for
>> + source AXI transaction
>> +- xlnx,overfetch: Tells whether the channel is allowed to over fetch the data
> (Maybe) s/Tells/Determines/
>> +- xlnx,src-issue: Number of AXI outstanding transactions on source side
>> +- xlnx,desc-axi-cohrnt: Tells whether the AXI transactions generated for the
>> + descriptor read are marked Non-coherent
> (Maybe) s/Tells/Determines/
>> +- xlnx,src-axi-cohrnt: Tells whether the AXI transactions generated for the
>> + source descriptor payload are marked Non-coherent
> same
>> +- xlnx,dst-axi-cohrnt: Tells whether the AXI transactions generated for the
>> + dst descriptor payload are marked Non-coherent
>> +- xlnx,desc-axi-qos: AXI QOS bits to be used for descriptor fetch
>> +- xlnx,src-axi-qos: AXI QOS bits to be used for data read
>> +- xlnx,dst-axi-qos: AXI QOS bits to be used for data write
>> +- xlnx,desc-axi-cache: AXI cache bits to be used for descriptor fetch.
>> +- xlnx,desc-axi-cache: AXI cache bits to be used for data read
>> +- xlnx,desc-axi-cache: AXI cache bits to be used for data write
>> +- xlnx,src-burst-len: AXI length for data read. Support only power of 2 values
>> + i.e 1,2,4,8 and 16
>> +- xlnx,dst-burst-len: AXI length for data write. Support only power of 2 values
>> + i.e 1,2,4,8 and 16
>> +
>> +Example:
>> +++++++++
>> +fpd_dma_chan1: dma@FD500000 {
>> + compatible = "xlnx,zynqmp-dma-1.0";
>> + reg = <0x0 0xFD500000 0x1000>;
>> + #dma_cells = <1>;
> #dma-cells = <1>;
>> + interrupt-parent = <&gic>;
>> + interrupts = <0 117 4>;
>> + xlnx,bus-width = <128>;
>> + xlnx,include-sg;
>> + xlnx,overfetch;
>> + xlnx,ratectrl = <0>;
>> + xlnx,src-issue = <16>;
>> + xlnx,desc-axi-cohrnt;
>> + xlnx,src-axi-cohrnt;
>> + xlnx,dst-axi-cohrnt;
>> + xlnx,desc-axi-qos = <0>;
>> + xlnx,desc-axi-cache = <0>;
>> + xlnx,src-axi-qos = <0>;
>> + xlnx,src-axi-cache = <2>;
>> + xlnx,dst-axi-qos = <0>;
>> + xlnx,dst-axi-cache = <2>;
>> + xlnx,src-burst-len = <4>;
>> + xlnx,dst-burst-len = <4>;
>> +};
>> --
>> 1.7.4
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
> Cheers,
>
> Moritz
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
