Hi Markus, > -----Original Message----- > From: Markus Pargmann [mailto:mpa@xxxxxxxxxxxxxx] > Sent: Wednesday, August 19, 2015 1:55 PM > To: Chen Haibo-B51421 > Cc: robh+dt@xxxxxxxxxx; pawel.moll@xxxxxxx; mark.rutland@xxxxxxx; > ijc+devicetree@xxxxxxxxxxxxxx; galak@xxxxxxxxxxxxxx; shawnguo@xxxxxxxxxx; > kernel@xxxxxxxxxxxxxx; linux@xxxxxxxxxxxxxxxx; dmitry.torokhov@xxxxxxxxx; > devicetree@xxxxxxxxxxxxxxx; sbranden@xxxxxxxxxxxx; arnd@xxxxxxxx; > mchehab@xxxxxxxxxxxxxxx; christian.gmeiner@xxxxxxxxx; > scott.liu@xxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx; hdegoede@xxxxxxxxxx; > jonathar@xxxxxxxxxxxx; benjamin.tissoires@xxxxxxxxxx; > hans.verkuil@xxxxxxxxx; hadess@xxxxxxxxxx; linux-input@xxxxxxxxxxxxxxx; > geert@xxxxxxxxxxxxxx; sebastien.szymanski@xxxxxxxxxxxx; > mamlinav@xxxxxxxxx; linux-arm-kernel@xxxxxxxxxxxxxxxxxxx > Subject: Re: [PATCH v2 2/5] Documentation: Detail permitted DT properties > for the imx6ul_tsc > > Hi, > > On Tue, Jul 28, 2015 at 05:58:38PM +0800, Haibo Chen wrote: > > Here we apply required documentation for the imx6ul touch screen > > controller driver which describe available properties and how to use > > them. > > > > Signed-off-by: Haibo Chen <haibo.chen@xxxxxxxxxxxxx> > > --- > > .../bindings/input/touchscreen/imx6ul_tsc.txt | 36 > ++++++++++++++++++++++ > > 1 file changed, 36 insertions(+) > > create mode 100644 > > Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt > > > > diff --git > > a/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt > > b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.txt > > new file mode 100644 > > index 0000000..ac41c32 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/input/touchscreen/imx6ul_tsc.t > > +++ xt > > @@ -0,0 +1,36 @@ > > +* Freescale i.MX6UL Touch Controller > > + > > +Required properties: > > +- compatible: must be "fsl,imx6ul-tsc". > > +- reg: this touch controller address and the ADC2 address. > > This suggests that this driver is using a unit ADC2. Which also means > that there are more than one ADC which are probably identical? > > Shouldn't these ADCs be properly described by their own device nodes > instead of these two register ranges, two interrupts and two clocks? > > Is 'ADC2' usable without tsc? Then ADC1/ADC2 should perhaps get a proper > IIO driver. For i.MX6UL, there are two ADC. ADC1 is a normal ADC, and ADC2 can only works for TSC, the channels of ADC2 are connected to TSC directly. TSC and ADC2 should work together as a touch screen controller. For ADC1, it share the driver vf610_adc.c (drivers/iio/adc/vf610_adc.c). Best Regards Haibo > > Unfortunately I don't have the reference manual to have a look how this > all works. > > Best regards, > > Markus > > > +- interrupts: the interrupt of this touch controller and ADC2. > > +- clocks: the root clock of touch controller and ADC2. > > +- clock-names; must be "tsc" and "adc". > > +- xnur-gpio: the X- gpio this controller connect to. > > + This xnur-gpio returns to high once the finger leave the touch > > +screen (The > > + last touch event the touch controller capture). > > + > > +Optional properties: > > +- measure-delay-time: the value of measure delay time. > > + Before X-axis or Y-axis measurement, the screen need some time > > +before > > + even potential distribution ready. > > + This value depends on the touch screen. > > +- pre-charge-time: the touch screen need some time to precharge. > > + This value depends on the touch screen. > > + > > +Example: > > + tsc: tsc@02040000 { > > + compatible = "fsl,imx6ul-tsc"; > > + reg = <0x02040000 0x4000>, <0x0219c000 0x4000>; > > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, > > + <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>; > > + clocks = <&clks IMX6UL_CLK_IPG>, > > + <&clks IMX6UL_CLK_ADC2>; > > + clock-names = "tsc", "adc"; > > + pinctrl-names = "default"; > > + pinctrl-0 = <&pinctrl_tsc>; > > + xnur-gpio = <&gpio1 3 GPIO_ACTIVE_HIGH>; > > + measure-delay-time = <0xfff>; > > + pre-charge-time = <0xffff>; > > + status = "okay"; > > + }; > > -- > > 1.9.1 > > > > > > > > -- > Pengutronix e.K. | > | > Industrial Linux Solutions | http://www.pengutronix.de/ > | > Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-0 > | > Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 > | ��.n��������+%������w��{.n����z�{��ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f
