Re: [PATCH v5 1/6] mmc: sdhci-esdhc-imx: add imx7d support and support HS400

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Mon, Aug 10, 2015 at 04:18:03PM +0800, Haibo Chen wrote:
> The imx7d usdhc is derived from imx6sx, the difference is that
> imx7d support HS400.
> 
> So introduce a new compatible string for imx7d and add HS400
> support for imx7d usdhc.
> 
> Signed-off-by: Haibo Chen <haibo.chen@xxxxxxxxxxxxx>
> ---
>  drivers/mmc/host/sdhci-esdhc-imx.c | 88 ++++++++++++++++++++++++++++++++++++--
>  1 file changed, 85 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
> index c6b9f64..2a816ad 100644
> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
> @@ -44,6 +44,7 @@
>  #define  ESDHC_MIX_CTRL_EXE_TUNE	(1 << 22)
>  #define  ESDHC_MIX_CTRL_SMPCLK_SEL	(1 << 23)
>  #define  ESDHC_MIX_CTRL_FBCLK_SEL	(1 << 25)
> +#define  ESDHC_MIX_CTRL_HS400_EN	(1 << 26)
>  /* Bits 3 and 6 are not SDHCI standard definitions */
>  #define  ESDHC_MIX_CTRL_SDHCI_MASK	0xb7
>  /* Tuning bits */
> @@ -60,6 +61,16 @@
>  #define  ESDHC_TUNE_CTRL_MIN		0
>  #define  ESDHC_TUNE_CTRL_MAX		((1 << 7) - 1)
>  
> +/* strobe dll register */
> +#define ESDHC_STROBE_DLL_CTRL		0x70
> +#define ESDHC_STROBE_DLL_CTRL_ENABLE	(1 << 0)
> +#define ESDHC_STROBE_DLL_CTRL_RESET	(1 << 1)
> +#define ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT	3
> +
> +#define ESDHC_STROBE_DLL_STATUS		0x74
> +#define ESDHC_STROBE_DLL_STS_REF_LOCK	(1 << 1)
> +#define ESDHC_STROBE_DLL_STS_SLV_LOCK	0x1
> +
>  #define ESDHC_TUNING_CTRL		0xcc
>  #define ESDHC_STD_TUNING_EN		(1 << 24)
>  /* NOTE: the minimum valid tuning start tap for mx6sl is 1 */
> @@ -120,6 +131,11 @@
>  #define ESDHC_FLAG_ERR004536		BIT(7)
>  /* The IP supports HS200 mode */
>  #define ESDHC_FLAG_HS200		BIT(8)
> +/* The IP supports HS400 mode */
> +#define ESDHC_FLAG_HS400		BIT(9)
> +
> +/* A higher clock ferquency than this rate requires strobell dll control */
> +#define ESDHC_STROBE_DLL_CLK_FREQ	100000000
>  
>  struct esdhc_soc_data {
>  	u32 flags;
> @@ -156,6 +172,12 @@ static struct esdhc_soc_data usdhc_imx6sx_data = {
>  			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200,
>  };
>  
> +static struct esdhc_soc_data usdhc_imx7d_data = {
> +	.flags = ESDHC_FLAG_USDHC | ESDHC_FLAG_STD_TUNING
> +			| ESDHC_FLAG_HAVE_CAP1 | ESDHC_FLAG_HS200
> +			| ESDHC_FLAG_HS400,
> +};
> +
>  struct pltfm_imx_data {
>  	u32 scratchpad;
>  	struct pinctrl *pinctrl;
> @@ -199,6 +221,7 @@ static const struct of_device_id imx_esdhc_dt_ids[] = {
>  	{ .compatible = "fsl,imx6sx-usdhc", .data = &usdhc_imx6sx_data, },
>  	{ .compatible = "fsl,imx6sl-usdhc", .data = &usdhc_imx6sl_data, },
>  	{ .compatible = "fsl,imx6q-usdhc", .data = &usdhc_imx6q_data, },
> +	{ .compatible = "fsl,imx7d-usdhc", .data = &usdhc_imx7d_data, },
>  	{ /* sentinel */ }
>  };
>  MODULE_DEVICE_TABLE(of, imx_esdhc_dt_ids);
> @@ -274,6 +297,9 @@ static u32 esdhc_readl_le(struct sdhci_host *host, int reg)
>  				val = SDHCI_SUPPORT_DDR50 | SDHCI_SUPPORT_SDR104
>  					| SDHCI_SUPPORT_SDR50
>  					| SDHCI_USE_SDR50_TUNING;
> +
> +			if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
> +				val |= SDHCI_SUPPORT_HS400;
>  		}
>  	}
>  
> @@ -774,6 +800,7 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
>  		break;
>  	case MMC_TIMING_UHS_SDR104:
>  	case MMC_TIMING_MMC_HS200:
> +	case MMC_TIMING_MMC_HS400:
>  		pinctrl = imx_data->pins_200mhz;
>  		break;
>  	default:
> @@ -784,12 +811,57 @@ static int esdhc_change_pinstate(struct sdhci_host *host,
>  	return pinctrl_select_state(imx_data->pinctrl, pinctrl);
>  }
>  
> +/*
> + * For HS400 eMMC, there is a data_strobe line, this signal is generated
> + * by the device and used for data output and CRC status response output
> + * in HS400 mode. The frequency of this signal follows the frequency of
> + * CLK generated by host. Host receive the data which is aligned to the
> + * edge of data_strobe line. Due to the time delay between CLK line and
> + * data_strobe line, if the delay time is larger than one clock cycle,
> + * then CLK and data_strobe line will misaligned, read error shows up.
> + * So when the CLK is higher than 100MHz, each clock cycle is short enough,
> + * host should config the delay target.
> + */
> +static void esdhc_set_strobe_dll(struct sdhci_host *host)
> +{
> +	u32 v;
> +
> +	if (host->mmc->actual_clock > ESDHC_STROBE_DLL_CLK_FREQ) {
> +		/* force a reset on strobe dll */
> +		writel(ESDHC_STROBE_DLL_CTRL_RESET,
> +			host->ioaddr + ESDHC_STROBE_DLL_CTRL);
> +		/*
> +		 * enable strobe dll ctrl and adjust the delay target
> +		 * for the uSDHC loopback read clock
> +		 */
> +		v = ESDHC_STROBE_DLL_CTRL_ENABLE |
> +			(7 << ESDHC_STROBE_DLL_CTRL_SLV_DLY_TARGET_SHIFT);
> +		writel(v, host->ioaddr + ESDHC_STROBE_DLL_CTRL);
> +		/* wait 1us to make sure strobe dll status register stable */
> +		udelay(1);
> +		v = readl(host->ioaddr + ESDHC_STROBE_DLL_STATUS);
> +		if (!(v & ESDHC_STROBE_DLL_STS_REF_LOCK))
> +			dev_warn(mmc_dev(host->mmc),
> +				"warning! HS400 strobe DLL status REF not lock!\n");
> +		if (!(v & ESDHC_STROBE_DLL_STS_SLV_LOCK))
> +			dev_warn(mmc_dev(host->mmc),
> +				"warning! HS400 strobe DLL status SLV not lock!\n");
> +	}
> +}
> +
>  static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
>  {
> +	u32 m;
>  	struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
>  	struct pltfm_imx_data *imx_data = pltfm_host->priv;
>  	struct esdhc_platform_data *boarddata = &imx_data->boarddata;
>  
> +	/* disable ddr mode and disable HS400 mode */
> +	m = readl(host->ioaddr + ESDHC_MIX_CTRL);
> +	m &= ~(ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN);
> +	writel(m, host->ioaddr + ESDHC_MIX_CTRL);

Is this write really required?

> +	imx_data->is_ddr = 0;
> +
>  	switch (timing) {
>  	case MMC_TIMING_UHS_SDR12:
>  	case MMC_TIMING_UHS_SDR25:
> @@ -799,9 +871,9 @@ static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
>  		break;
>  	case MMC_TIMING_UHS_DDR50:
>  	case MMC_TIMING_MMC_DDR52:
> -		writel(readl(host->ioaddr + ESDHC_MIX_CTRL) |
> -				ESDHC_MIX_CTRL_DDREN,
> -				host->ioaddr + ESDHC_MIX_CTRL);
> +		m = readl(host->ioaddr + ESDHC_MIX_CTRL);

Can this line be droped if using the former readback mixctl value?

> +		m |= ESDHC_MIX_CTRL_DDREN;
> +		writel(m, host->ioaddr + ESDHC_MIX_CTRL);
>  		imx_data->is_ddr = 1;
>  		if (boarddata->delay_line) {
>  			u32 v;
> @@ -813,6 +885,13 @@ static void esdhc_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
>  			writel(v, host->ioaddr + ESDHC_DLL_CTRL);
>  		}
>  		break;
> +	case MMC_TIMING_MMC_HS400:
> +		m = readl(host->ioaddr + ESDHC_MIX_CTRL);

ditto

Regards
Dong Aisheng

> +		m |= ESDHC_MIX_CTRL_DDREN | ESDHC_MIX_CTRL_HS400_EN;
> +		writel(m, host->ioaddr + ESDHC_MIX_CTRL);
> +		imx_data->is_ddr = 1;
> +		esdhc_set_strobe_dll(host);
> +		break;
>  	}
>  
>  	esdhc_change_pinstate(host, timing);
> @@ -1100,6 +1179,9 @@ static int sdhci_esdhc_imx_probe(struct platform_device *pdev)
>  	if (imx_data->socdata->flags & ESDHC_FLAG_ERR004536)
>  		host->quirks |= SDHCI_QUIRK_BROKEN_ADMA;
>  
> +	if (imx_data->socdata->flags & ESDHC_FLAG_HS400)
> +		host->quirks2 |= SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400;
> +
>  	if (of_id)
>  		err = sdhci_esdhc_imx_probe_dt(pdev, host, imx_data);
>  	else
> -- 
> 1.9.1
> 
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux