Hello Dmitry,
On 15-07-21 10:20:44, Dmitry Torokhov wrote:
> Hi Stefan,
>
> On Tue, Jul 21, 2015 at 04:43:36PM +0200, Stefan Agner wrote:
> > Hi Dmitry,
> >
> > As the original author of the driver I have some remarks to your review
> >
> > On 2015-07-18 01:42, Dmitry Torokhov wrote:
> > >> + /*
> > >> + * If touch pressure is too low, stop measuring and reenable
> > >> + * touch detection
> > >> + */
> > >> + if (val_p < min_pressure || val_p > 2000)
> > >> + break;
> >
> > This is where the modules touch pressure is used to stop the measurement
> > process and switch back to interrupt mode. See my remarks at the end.
> >
> > >> +
> > >> + /*
> > >> + * The pressure may not be enough for the first x and the
> > >> + * second y measurement, but, the pressure is ok when the
> > >> + * driver is doing the third and fourth measurement. To
> > >> + * take care of this, we drop the first measurement always.
> > >> + */
> > >> + if (discard_val_on_start) {
> > >> + discard_val_on_start = false;
> > >> + } else {
> > >> + /*
> > >> + * Report touch position and sleep for
> > >> + * next measurement
> > >> + */
> > >> + input_report_abs(vf50_ts->ts_input,
> > >> + ABS_X, VF_ADC_MAX - val_x);
> > >> + input_report_abs(vf50_ts->ts_input,
> > >> + ABS_Y, VF_ADC_MAX - val_y);
> > >> + input_report_abs(vf50_ts->ts_input,
> > >> + ABS_PRESSURE, val_p);
> > >> + input_report_key(vf50_ts->ts_input, BTN_TOUCH, 1);
> > >> + input_sync(vf50_ts->ts_input);
> > >> + }
> > >> +
> > >> + msleep(10);
> > >> + }
> > >> +
> > >> + /* Report no more touch, reenable touch detection */
> > >> + input_report_abs(vf50_ts->ts_input, ABS_PRESSURE, 0);
> > >> + input_report_key(vf50_ts->ts_input, BTN_TOUCH, 0);
> > >> + input_sync(vf50_ts->ts_input);
> > >> +
> > >> + vf50_ts_enable_touch_detection(vf50_ts);
> > >> +
> > >> + /* Wait for the pull-up to be stable on high */
> > >> + msleep(10);
> > >> +
> > >> + /* Reenable IRQ to detect touch */
> > >> + enable_irq(vf50_ts->pen_irq);
> > >> +
> > >> + dev_dbg(dev, "Reenabled touch detection interrupt\n");
> > >> +}
> > >> +
> > >> +static irqreturn_t vf50_ts_touched(int irq, void *dev_id)
> > >> +{
> > >> + struct vf50_touch_device *vf50_ts = (struct vf50_touch_device *)dev_id;
> > >> + struct device *dev = &vf50_ts->pdev->dev;
> > >> +
> > >> + dev_dbg(dev, "Touch detected, start worker thread\n");
> > >> +
> > >> + disable_irq_nosync(irq);
> > >> +
> > >> + /* Disable the touch detection plates */
> > >> + gpiod_set_value(vf50_ts->gpio_ym, 0);
> > >> +
> > >> + /* Let the platform mux to default state in order to mux as ADC */
> > >> + pinctrl_pm_select_default_state(dev);
> > >> +
> > >> + queue_work(vf50_ts->ts_workqueue, &vf50_ts->ts_work);
> > >
> > > If you convert this to a threaded interrupt you won't need to
> > > disable/reenable interrupt or queue work. You should also be able to use
> > > gpiod_set_value_cansleep() extending the range of ways the controller
> > > could be connected to systems.
> > >
> >
> > I'm not sure if a threaded interrupt is the right thing here. While the
> > pen is on the touchscreen (which can be for several seconds)
> > measurements have to be made in a continuous loop. Is it ok for a
> > threaded interrupt to run that long?
>
> Yes, why not? Threaded interrupt is simply a kernel thread that is woken
> when hard interrupt handler tells it to wake up. Very similar to
> interrupt + work queue, except that the kernel manages interactions
> properly for you. There are several drivers in kernel that do that, for
> example auo-pixcir-ts.c or tsc2007.c
>
> >
> > I'm also not sure if it is really safe to _not_ disable the pen down
> > GPIO interrupt. If we get a interrupt while measuring, we should ignore
> > that interrupt.
>
> The interrupt management core (you'll have to annotate it as
> IRQF_ONESHOT) will make sure it stays masked properly until the threaded
> handler completes so you do not need to disable it explicitly.
After working some more on threaded irq implementation, if IRQ_ONESHOT
flag is used while requesting threaded irq, on entering the IRQ handler
the vf610_gpio_irq_mask is not called and vf610_gpio_irq_unmask is not
called on exiting the thread function, not something we expected.
In contrast, using explicit disable_irq_nosync and enable_irq in the IRQ
handler and thread respectively results in the respective mask and unmask
function being called.
The vf610_gpio_irq_*mask functions are in the gpio driver for Vybrid in
drivers/gpio/gpio-vf610.c.
Can you point me in the right direction?
Thanks & Regards,
Sanchayan.
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
