On 29/07/15 00:12, Martin Kepplinger wrote:
> Am 2015-07-28 um 11:28 schrieb Mark Rutland:
>> On Tue, Jul 28, 2015 at 10:11:29AM +0100, Martin Kepplinger wrote:
>>>
>>>
>>> On 2015-07-27 19:33, Mark Rutland wrote:
>>>> On Mon, Jul 27, 2015 at 03:37:48PM +0100, Martin Kepplinger wrote:
>>>>> Am 2015-07-27 um 16:23 schrieb Mark Rutland:
>>>>>> On Mon, Jul 27, 2015 at 03:08:15PM +0100, Martin Kepplinger wrote:
>>>>>>> For the devices supported by the mma8452 driver, two interrupt pins are
>>>>>>> available to route the interrupt signals to. By default INT1 is assumed.
>>>>>>>
>>>>>>> This adds a bitmask DT property for users to configure interrupt sources
>>>>>>> for INT2, if that is the wired interrupt pin for them.
>>>>>>
>>>>>> This sounds like configureation rather than a HW property. Why does this
>>>>>> need to be in the DT?
>>>>>
>>>>> It's a hardware property of the board that uses the device. There might
>>>>> be boards that connect just one of them at random, which is the reason
>>>>> for this DT property. There also might be exotic users who will want
>>>>> to use both pins to route different interrupt sources to (not yet
>>>>> supported, but no problem with such a bitmask).
>>>>
>>>> Ok, so I'm somewhat confused as to what the hardware looks like and what
>>>> this means.
>>>>
>>>> Could you elaborate on how INT1 and INT2 are used? It looks like they're
>>>> used as output pins, and so interrupt-names would seem appropriate for
>>>> describing the combination which is wired up.
>>>
>>> They are just the chip's two possible interrupt lines for us to get
>>> notified about event.
>>
>> Ok. So that matches my understanding.
>>
>>> You build a board, you use one of these 4 chips, wiring up just one of
>>> the 2 interrupt pins. By far most people won't ever need both pins.
>>>
>>> DT describes your hardware, right? So you describe how you built your
>>> board (wired the accelerometer chip) with this DT property.
>>
>> Ok.
>>
>>>> w.r.t. configuring the choice of output(s), that sounds like a runtime
>>>> decision rather than something which needs to be configured statically.
>>>
>>> This won't be useful during runtime. (De)activating events is what you
>>> do in iio sysfs.
>>>
>>> Even in the rare case (maybe supported in the future) when you want one
>>> interrupt source on one pin and another source on the other pin, that
>>> describes your hardware. You wire, say, data-ready to Linux and
>>> motion-detection to some strange alarm system. When you change your
>>> hardware (say, use Linux for both pins), I think it would justify
>>> changing a DT property.
>>
>> In that case you would need additional properties anyway.
>>
>>> Btw, we are talking about very theoretical stuff here. For now (and even
>>> possibly forever) we just don't ever want to break a DT propery we
>>> introduce here, thus the bitmask.
>>
>> I don't think you need the bitmask.
>>
>> I think all you need is interrupt-names, e.g.
>>
>> dev1 {
>> /* both wired up */
>> interrupts = <&some_ic 0 47>, <&some_ic 5 62>;
>> interrupt-names = "INT1", "INT2";
>> }
>>
>> dev2 {
>> /* only INT2 wired up */
>> interrupts = <&some_ic 3 96>;
>> interrupt-names = "INT2";
>> }
>>
>> You can figure out which interrupts are wired up by trying to acquire
>> them by name, then falling back to acquiting an anonymouos interrupt
>> (assuming it's INT1) to keep compatible with existing DTBs. You can
>> choose which to use arbitrarily, try to load balance, or whatever you'd
>> like.
>>
>> If it's later necessary to route some interrupts to another device,
>> additional properties can be added to accomodate that. We already know
>> that the bitmask alone is not sufficient for that case.
>>
>
> Yes, this sounds reasonable indeed. I like the idea. I'm sorry I won't
> rewrite patch 8/8 now. Relocation and a lot to do before holidays. I'll
> be happy to write and test this properly in one month from now, if not
> done by somebody until then.
>
> Until then, since patches 1-7 only introduce a bindings document, they
> shouldn't be problematic for devicetree people.
>
>
> So if Jonathan and IIO people find anybody for review, feel free to take
> patches 1-7. In any case, there is direct register access via debugfs to
> at least somehow make the driver work for everybody ;)
>
> so long, thanks.
> martin
Cool, will kick this one into the long grass until you get back most
likely!
Have a good holiday when you get to it!
Jonathan
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
