On 28 July 2015 06:40, Dmitry Torokhov wrote: > Subject: Re: [PATCH V3 3/3] devicetree: da9062: Add device tree bindings for DA9062 OnKey > > On Mon, Jul 27, 2015 at 03:43:00PM -0700, Dmitry Torokhov wrote: > > On Thu, Jul 23, 2015 at 05:17:41PM +0100, S Twiss wrote: > > > From: S Twiss <stwiss.opensource@xxxxxxxxxxx> > > > > > > Add device tree bindings for the DA9062 OnKey driver component > > > > > > Signed-off-by: Steve Twiss <stwiss.opensource@xxxxxxxxxxx> > > > --- > > > This patch applies against linux-next and next-20150708 > > > > > > > > > .../devicetree/bindings/input/da9062-onkey.txt | 36 > ++++++++++++++++++++++ > > > Documentation/devicetree/bindings/mfd/da9062.txt | 3 ++ > > > > I dropped bits for mfd/da9062.txt, changed to mention both 9062 and > > 9063, folded into the onkey patch and applied. > > Argh, da9062 core is not in mainline yet... OK, below is the patch I > had; if Lee does not pick it up I'll re-apply it when da9062 core hits > mainline. > > Thanks. > -- > Dmitry Thanks Dmitry, The DA9062 core has been in linux-next for a couple of weeks now I think. Hi Lee, I'm not certain of the procedure with this: the DA9062 core is in linux-next/next-2015mmdd but has not yet made it to a mainline/v4.2-rcX so I guess it's not getting picked up for some other patches I have submitted for the DA9062 OnKey and RTC -- actually you already know about those two patch threads because you reviewed the MFD and DT parts last week! Oh well -- I guess I have drawn your attention to this anyway, I'm just not certain of the timeline on this because it's something I've not done before. Regards, Stephen > Input: add DA9062 OnKey capability to DA9063 OnKey driver > > From: S Twiss <stwiss.opensource@xxxxxxxxxxx> > > Add DA9062 OnKey support into the existing DA9063 OnKey driver > component by > using generic access tables for common register and bit mask definitions. > > The following change will add generic register and bit mask support to the > DA9063 OnKey. > > The following alterations have been made to the DA9063 OnKey: > > - Addition of a da906x_chip_config structure to hold all > generic registers and bitmasks for this type of OnKey component. > - Addition of an struct of_device_id table for DA9063 and DA9062 > defaults > - Refactoring functions to use struct da9063_onkey accesses to generic > registers/masks instead of using defines from registers.h > - Re-work of da9063_onkey_probe() to use of_match_node() and > dev_get_regmap() to provide initialisation of generic registers and > masks and access to regmap > > Signed-off-by: Steve Twiss <stwiss.opensource@xxxxxxxxxxx> > Signed-off-by: Dmitry Torokhov <dmitry.torokhov@xxxxxxxxx> > --- > .../devicetree/bindings/input/da9062-onkey.txt | 32 +++++ > drivers/input/misc/Kconfig | 8 + > drivers/input/misc/da9063_onkey.c | 129 ++++++++++++++++---- > 3 files changed, 140 insertions(+), 29 deletions(-) > create mode 100644 Documentation/devicetree/bindings/input/da9062- > onkey.txt > > diff --git a/Documentation/devicetree/bindings/input/da9062-onkey.txt > b/Documentation/devicetree/bindings/input/da9062-onkey.txt > new file mode 100644 > index 0000000..ab0e048 > --- /dev/null > +++ b/Documentation/devicetree/bindings/input/da9062-onkey.txt > @@ -0,0 +1,32 @@ > +* Dialog DA9062/63 OnKey Module > + > +This module is part of the DA9062/DA9063. For more details about entire > +chips see Documentation/devicetree/bindings/mfd/da9062.txt and > +Documentation/devicetree/bindings/mfd/da9063.txt > + > +This module provides KEY_POWER, KEY_SLEEP and events. > + > +Required properties: > + > + - compatible: should be one of: > + dlg,da9062-onkey > + dlg,da9063-onkey > + > +Optional properties: > + > + - dlg,disable-key-power : Disable power-down using a long key-press. If > this > + entry exists the OnKey driver will remove support for the KEY_POWER > key > + press. If this entry does not exist then by default the key-press > + triggered power down is enabled and the OnKey will support both > KEY_POWER > + and KEY_SLEEP. > + > +Example: > + > + pmic0: da9062@58 { > + > + onkey { > + compatible = "dlg,da9063-onkey"; > + dlg,disable-key-power; > + }; > + > + }; > diff --git a/drivers/input/misc/Kconfig b/drivers/input/misc/Kconfig > index d4f0a81..d4b993d 100644 > --- a/drivers/input/misc/Kconfig > +++ b/drivers/input/misc/Kconfig > @@ -611,11 +611,11 @@ config INPUT_DA9055_ONKEY > will be called da9055_onkey. > > config INPUT_DA9063_ONKEY > - tristate "Dialog DA9063 OnKey" > - depends on MFD_DA9063 > + tristate "Dialog DA9062/63 OnKey" > + depends on MFD_DA9063 || MFD_DA9062 > help > - Support the ONKEY of Dialog DA9063 Power Management IC as an > - input device reporting power button statue. > + Support the ONKEY of Dialog DA9063 and DA9062 Power > Management ICs > + as an input device capable of reporting the power button status. > > To compile this driver as a module, choose M here: the module > will be called da9063_onkey. > diff --git a/drivers/input/misc/da9063_onkey.c > b/drivers/input/misc/da9063_onkey.c > index f577585..8eb697d 100644 > --- a/drivers/input/misc/da9063_onkey.c > +++ b/drivers/input/misc/da9063_onkey.c > @@ -1,5 +1,5 @@ > /* > - * OnKey device driver for DA9063 > + * OnKey device driver for DA9063 and DA9062 PMICs > * Copyright (C) 2015 Dialog Semiconductor Ltd. > * > * This program is free software; you can redistribute it and/or > @@ -24,36 +24,96 @@ > #include <linux/mfd/da9063/core.h> > #include <linux/mfd/da9063/pdata.h> > #include <linux/mfd/da9063/registers.h> > +#include <linux/mfd/da9062/core.h> > +#include <linux/mfd/da9062/registers.h> > + > +struct da906x_chip_config { > + /* REGS */ > + int onkey_status; > + int onkey_pwr_signalling; > + int onkey_fault_log; > + int onkey_shutdown; > + /* MASKS */ > + int onkey_nonkey_mask; > + int onkey_nonkey_lock_mask; > + int onkey_key_reset_mask; > + int onkey_shutdown_mask; > + /* NAMES */ > + const char *name; > +}; > > struct da9063_onkey { > - struct da9063 *hw; > struct delayed_work work; > struct input_dev *input; > struct device *dev; > + struct regmap *regmap; > + const struct da906x_chip_config *config; > + char phys[32]; > bool key_power; > }; > > +static const struct da906x_chip_config da9063_regs = { > + /* REGS */ > + .onkey_status = DA9063_REG_STATUS_A, > + .onkey_pwr_signalling = DA9063_REG_CONTROL_B, > + .onkey_fault_log = DA9063_REG_FAULT_LOG, > + .onkey_shutdown = DA9063_REG_CONTROL_F, > + /* MASKS */ > + .onkey_nonkey_mask = DA9063_NONKEY, > + .onkey_nonkey_lock_mask = DA9063_NONKEY_LOCK, > + .onkey_key_reset_mask = DA9063_KEY_RESET, > + .onkey_shutdown_mask = DA9063_SHUTDOWN, > + /* NAMES */ > + .name = DA9063_DRVNAME_ONKEY, > +}; > + > +static const struct da906x_chip_config da9062_regs = { > + /* REGS */ > + .onkey_status = DA9062AA_STATUS_A, > + .onkey_pwr_signalling = DA9062AA_CONTROL_B, > + .onkey_fault_log = DA9062AA_FAULT_LOG, > + .onkey_shutdown = DA9062AA_CONTROL_F, > + /* MASKS */ > + .onkey_nonkey_mask = DA9062AA_NONKEY_MASK, > + .onkey_nonkey_lock_mask = DA9062AA_NONKEY_LOCK_MASK, > + .onkey_key_reset_mask = DA9062AA_KEY_RESET_MASK, > + .onkey_shutdown_mask = DA9062AA_SHUTDOWN_MASK, > + /* NAMES */ > + .name = "da9062-onkey", > +}; > + > +static const struct of_device_id da9063_compatible_reg_id_table[] = { > + { .compatible = "dlg,da9063-onkey", .data = &da9063_regs }, > + { .compatible = "dlg,da9062-onkey", .data = &da9062_regs }, > + { }, > +}; > + > static void da9063_poll_on(struct work_struct *work) > { > - struct da9063_onkey *onkey = container_of(work, struct > da9063_onkey, > - work.work); > + struct da9063_onkey *onkey = container_of(work, > + struct da9063_onkey, > + work.work); > + const struct da906x_chip_config *config = onkey->config; > unsigned int val; > int fault_log = 0; > bool poll = true; > int error; > > /* Poll to see when the pin is released */ > - error = regmap_read(onkey->hw->regmap, > DA9063_REG_STATUS_A, &val); > + error = regmap_read(onkey->regmap, > + config->onkey_status, > + &val); > if (error) { > dev_err(onkey->dev, > "Failed to read ON status: %d\n", error); > goto err_poll; > } > > - if (!(val & DA9063_NONKEY)) { > - error = regmap_update_bits(onkey->hw->regmap, > - DA9063_REG_CONTROL_B, > - DA9063_NONKEY_LOCK, 0); > + if (!(val & config->onkey_nonkey_mask)) { > + error = regmap_update_bits(onkey->regmap, > + config->onkey_pwr_signalling, > + config->onkey_nonkey_lock_mask, > + 0); > if (error) { > dev_err(onkey->dev, > "Failed to reset the Key Delay %d\n", error); > @@ -70,15 +130,16 @@ static void da9063_poll_on(struct work_struct > *work) > * If the fault log KEY_RESET is detected, then clear it > * and shut down the system. > */ > - error = regmap_read(onkey->hw->regmap, > - DA9063_REG_FAULT_LOG, &fault_log); > + error = regmap_read(onkey->regmap, > + config->onkey_fault_log, > + &fault_log); > if (error) { > dev_warn(&onkey->input->dev, > "Cannot read FAULT_LOG: %d\n", error); > - } else if (fault_log & DA9063_KEY_RESET) { > - error = regmap_write(onkey->hw->regmap, > - DA9063_REG_FAULT_LOG, > - DA9063_KEY_RESET); > + } else if (fault_log & config->onkey_key_reset_mask) { > + error = regmap_write(onkey->regmap, > + config->onkey_fault_log, > + config->onkey_key_reset_mask); > if (error) { > dev_warn(&onkey->input->dev, > "Cannot reset KEY_RESET fault log: %d\n", > @@ -88,10 +149,10 @@ static void da9063_poll_on(struct work_struct > *work) > * and then send shutdown command > */ > dev_dbg(&onkey->input->dev, > - "Sending SHUTDOWN to DA9063 ...\n"); > - error = regmap_write(onkey->hw->regmap, > - DA9063_REG_CONTROL_F, > - DA9063_SHUTDOWN); > + "Sending SHUTDOWN to DA9063 ...\n"); > + error = regmap_write(onkey->regmap, > + config->onkey_shutdown, > + config->onkey_shutdown_mask); > if (error) > dev_err(&onkey->input->dev, > "Cannot SHUTDOWN DA9063: %d\n", > @@ -107,11 +168,14 @@ err_poll: > static irqreturn_t da9063_onkey_irq_handler(int irq, void *data) > { > struct da9063_onkey *onkey = data; > + const struct da906x_chip_config *config = onkey->config; > unsigned int val; > int error; > > - error = regmap_read(onkey->hw->regmap, > DA9063_REG_STATUS_A, &val); > - if (onkey->key_power && !error && (val & DA9063_NONKEY)) { > + error = regmap_read(onkey->regmap, > + config->onkey_status, > + &val); > + if (onkey->key_power && !error && (val & config- > >onkey_nonkey_mask)) { > input_report_key(onkey->input, KEY_POWER, 1); > input_sync(onkey->input); > schedule_delayed_work(&onkey->work, 0); > @@ -139,9 +203,15 @@ static int da9063_onkey_probe(struct > platform_device *pdev) > struct da9063 *da9063 = dev_get_drvdata(pdev->dev.parent); > struct da9063_pdata *pdata = dev_get_platdata(da9063->dev); > struct da9063_onkey *onkey; > + const struct of_device_id *match; > int irq; > int error; > > + match = of_match_node(da9063_compatible_reg_id_table, > + pdev->dev.of_node); > + if (!match) > + return -ENXIO; > + > onkey = devm_kzalloc(&pdev->dev, sizeof(struct da9063_onkey), > GFP_KERNEL); > if (!onkey) { > @@ -149,8 +219,14 @@ static int da9063_onkey_probe(struct > platform_device *pdev) > return -ENOMEM; > } > > + onkey->config = match->data; > onkey->dev = &pdev->dev; > - onkey->hw = da9063; > + > + onkey->regmap = dev_get_regmap(pdev->dev.parent, NULL); > + if (!onkey->regmap) { > + dev_err(&pdev->dev, "Parent regmap unavailable.\n"); > + return -ENXIO; > + } > > if (pdata) > onkey->key_power = pdata->key_power; > @@ -165,8 +241,10 @@ static int da9063_onkey_probe(struct > platform_device *pdev) > return -ENOMEM; > } > > - onkey->input->name = DA9063_DRVNAME_ONKEY; > - onkey->input->phys = DA9063_DRVNAME_ONKEY "/input0"; > + onkey->input->name = onkey->config->name; > + snprintf(onkey->phys, sizeof(onkey->phys), "%s/input0", > + onkey->config->name); > + onkey->input->phys = onkey->phys; > onkey->input->dev.parent = &pdev->dev; > > if (onkey->key_power) > @@ -216,11 +294,12 @@ static struct platform_driver da9063_onkey_driver > = { > .probe = da9063_onkey_probe, > .driver = { > .name = DA9063_DRVNAME_ONKEY, > + .of_match_table = da9063_compatible_reg_id_table, > }, > }; > module_platform_driver(da9063_onkey_driver); > > MODULE_AUTHOR("S Twiss <stwiss.opensource@xxxxxxxxxxx>"); > -MODULE_DESCRIPTION("Onkey device driver for Dialog DA9063"); > +MODULE_DESCRIPTION("Onkey device driver for Dialog DA9063 and > DA9062"); > MODULE_LICENSE("GPL"); > MODULE_ALIAS("platform:" DA9063_DRVNAME_ONKEY); -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html