Le 23/07/2015 21:48, Boris Brezillon a écrit :
> On Thu, 23 Jul 2015 18:42:55 +0200
> Cyrille Pitchen <cyrille.pitchen@xxxxxxxxx> wrote:
>
>> This patch documents the DT bindings for the Atmel Flexcom which will be
>> introduced by sama5d2x SoCs. These bindings will be used by the actual
>> Flexcom driver to be sent in another patch.
>>
>> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@xxxxxxxxx>
>> ---
>> .../devicetree/bindings/mfd/atmel-flexcom.txt | 68 ++++++++++++++++++++++
>> 1 file changed, 68 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
>> new file mode 100644
>> index 000000000000..a63226b7a9cb
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mfd/atmel-flexcom.txt
>> @@ -0,0 +1,68 @@
>> +* Device tree bindings for Atmel Flexcom (Flexible Serial Communication Unit)
>> +
>> +The Atmel Flexcom is just a wrapper which embeds a SPI controller, an I2C
>> +controller and an USART. Only one function can be used at a time and is chosen
>> +at boot time according to the device tree.
>> +
>> +Required properties:
>> +- compatible: Should be "atmel,sama5d2-flexcom"
>> +- reg: Should be the pair (offset, size) for the Flexcom
>> + dedicated I/O registers (without USART, TWI or SPI
>> + registers).
>> +- clocks: Should be the Flexcom peripheral clock from PMC.
>> +- #address-cells: Should be <2>
>> +- #size-cells: Should be <1>
>> +- ranges: Should be a list of ranges.
>> + One range per peripheral wrapped by the Flexcom. So each
>> + range is a triplet (child_addr, parent_addr, size). The
>> + first u32 of "child_addr" is the value to be set in the
>> + Operating Mode bitfield of the Flexcom Mode Register.
>> + Then "parent_addr" stores the base address of the
>> + corresponding peripheral in the system memory. Finally,
>> + "size" if the size of the memory region of this
>> + peripheral.
>> +
>> +Required child:
>> +A single available child for the serial controller to enable.
>> +
>> +Required properties of this child:
>> +- reg: Should be a pair (child_addr, size) with child_addr
>> + matching one of the parent ranges.
>> +- clocks: Should be the very same phandle as for the parent's one.
>> +
>> +Other properties remain unchanged. See documentation of the respective device:
>> +- ../serial/atmel-usart.txt
>> +- ../spi/spi_atmel.txt
>> +- ../i2c/i2c-at91.txt
>> +
>> +Example:
>> +
>> +flexcom@f8034000 {
>> + compatible = "atmel,sama5d2-flexcom";
>> + reg = <0xf8034000 0x200>;
>> + clocks = <&flx0_clk>;
>> + #address-cells = <2>;
>> + #size-cells = <1>;
>> + ranges = <1 0 0xf8034200 0x200 /* opmode 1: USART */
>> + 2 0 0xf8034400 0x200 /* opmode 2: SPI */
>> + 3 0 0xf8034600 0x200>; /* opmode 3: I2C */
Yes, the opmode(s) are exactly the values described in the product
datasheet.
>> +
>> + spi@f8034400 {
>
> Should be:
>
> spi@2,0 {
Yep!
I was silently following the discussion in the background and I admit
that this approach is pretty elegant.
So, if this approach is validated you can also add my:
Acked-by: Nicolas Ferre <nicolas.ferre@xxxxxxxxx>
>> + compatible = "atmel,at91rm9200-spi";
>> + reg = <2 0 0x200>;
>> + interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
>> + pinctrl-names = "default";
>> + pinctrl-0 = <&pinctrl_flx0_default>;
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + clocks = <&flx0_clk>;
>> + clock-names = "spi_clk";
>> + atmel,fifo-size = <32>;
>> +
>> + mtd_dataflash@0 {
>> + compatible = "atmel,at25f512b";
>> + reg = <0>;
>> + spi-max-frequency = <20000000>;
>> + };
>> + };
>> +};
>
>
>
--
Nicolas Ferre
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
