Re: [PATCH v2 3/5] usb: phy: add usb3.0 phy driver for mt65xx SoCs

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Fri, 2015-07-10 at 08:42 +0200, Sascha Hauer wrote:
> On Wed, Jul 08, 2015 at 05:41:05PM +0800, Chunfeng Yun wrote:
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@xxxxxxxxxxxx>
> > ---
> >  drivers/usb/phy/Kconfig           |  10 +
> >  drivers/usb/phy/Makefile          |   1 +
> >  drivers/usb/phy/phy-mt65xx-usb3.c | 856 ++++++++++++++++++++++++++++++++++++++
> >  3 files changed, 867 insertions(+)
> >  create mode 100644 drivers/usb/phy/phy-mt65xx-usb3.c
> > 
> > diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
> > index 869c0cfcad..66ded00 100644
> > --- a/drivers/usb/phy/Kconfig
> > +++ b/drivers/usb/phy/Kconfig
> > @@ -152,6 +152,16 @@ config USB_MSM_OTG
> >  	  This driver is not supported on boards like trout which
> >  	  has an external PHY.
> >  
> > +config USB_MT65XX_USB3_PHY
> > +	tristate "Mediatek USB3.0 PHY controller Driver"
> > +	depends on ARCH_MEDIATEK || COMPILE_TEST
> > +	select USB_PHY
> > +	help
> > +	  Say 'Y' here to add support for Mediatek USB3.0 PHY driver
> > +	  for mt65xx SoCs. it supports two usb2.0 ports and
> > +	  one usb3.0 port.
> > +	  To compile this driver as a module, choose M here
> > +
> >  config USB_MV_OTG
> >  	tristate "Marvell USB OTG support"
> >  	depends on USB_EHCI_MV && USB_MV_UDC && PM
> > diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
> > index e36ab1d..414ef57 100644
> > --- a/drivers/usb/phy/Makefile
> > +++ b/drivers/usb/phy/Makefile
> > @@ -20,6 +20,7 @@ obj-$(CONFIG_USB_EHCI_TEGRA)		+= phy-tegra-usb.o
> >  obj-$(CONFIG_USB_GPIO_VBUS)		+= phy-gpio-vbus-usb.o
> >  obj-$(CONFIG_USB_ISP1301)		+= phy-isp1301.o
> >  obj-$(CONFIG_USB_MSM_OTG)		+= phy-msm-usb.o
> > +obj-$(CONFIG_USB_MT65XX_USB3_PHY)	+= phy-mt65xx-usb3.o
> >  obj-$(CONFIG_USB_MV_OTG)		+= phy-mv-usb.o
> >  obj-$(CONFIG_USB_MXS_PHY)		+= phy-mxs-usb.o
> >  obj-$(CONFIG_USB_RCAR_PHY)		+= phy-rcar-usb.o
> > diff --git a/drivers/usb/phy/phy-mt65xx-usb3.c b/drivers/usb/phy/phy-mt65xx-usb3.c
> > new file mode 100644
> > index 0000000..38ee6f3
> > --- /dev/null
> > +++ b/drivers/usb/phy/phy-mt65xx-usb3.c
> > @@ -0,0 +1,856 @@
> > +/*
> > + * Copyright (c) 2015 MediaTek Inc.
> > + * Author: Chunfeng.Yun <chunfeng.yun@xxxxxxxxxxxx>
> > + *
> > + * This software is licensed under the terms of the GNU General Public
> > + * License version 2, as published by the Free Software Foundation, and
> > + * may be copied, distributed, and modified under those terms.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> > + * GNU General Public License for more details.
> > + *
> > + */
> > +
> > +#include <linux/clk.h>
> > +#include <linux/delay.h>
> > +#include <linux/err.h>
> > +#include <linux/export.h>
> > +#include <linux/gpio.h>
> > +#include <linux/io.h>
> > +#include <linux/iopoll.h>
> > +#include <linux/mfd/syscon.h>
> > +#include <linux/module.h>
> > +#include <linux/of_address.h>
> > +#include <linux/of_device.h>
> > +#include <linux/of_gpio.h>
> > +#include <linux/of.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/regmap.h>
> > +#include <linux/regulator/consumer.h>
> > +#include <linux/resource.h>
> > +#include <linux/slab.h>
> > +#include <linux/usb/of.h>
> > +#include <linux/usb/otg.h>
> > +#include <linux/usb/phy.h>
> > +
> > +/*
> > + * relative to MAC base address
> > + */
> > +#define SSUSB_USB3_MAC_CSR_BASE	(0x1400)
> > +#define SSUSB_USB3_SYS_CSR_BASE	(0x1400)
> > +#define SSUSB_USB2_CSR_BASE	(0x2400)
> 
> Please drop the unnecessary braces.
> 
ok
> > +
> > +/*
> > + * for sifslv1 register
> > + * relative to USB3_SIF_BASE base address
> > + */
> > +#define SSUSB_SIFSLV_IPPC_BASE	(0x700)
> > +
> > +/*
> > + * for sifslv2 register
> > + * relative to USB3_SIF_BASE base address
> > + */
> > +#define SSUSB_SIFSLV_U2PHY_COM_BASE	(0x10800)
> > +#define SSUSB_SIFSLV_U3PHYD_BASE	(0x10900)
> > +#define SSUSB_SIFSLV_U2FREQ_BASE	(0x10f00)
> > +#define SSUSB_USB30_PHYA_SIV_B_BASE	(0x10b00)
> > +#define SSUSB_SIFSLV_U3PHYA_DA_BASE	(0x10c00)
> > +#define SSUSB_SIFSLV_SPLLC	(0x10000)
> > +
> > +/*port1 refs. +0x800(refer to port0)*/
> > +#define U3P_PORT_OFFSET (0x800)	/*based on port0 */
> > +#define U3P_PHY_BASE(index) ((U3P_PORT_OFFSET) * (index))
> 
> According to my datasheet port(idx) base is at:
> 
> sif_base + 0x800 + 0x100 * idx
> 
> Am I missing something here?
Maybe, ssusb_sifslv_u2_phy_com_T28_Xp etc(X = 1,2,3,4)
and their interval is 0x800
 
> > +
> > +#define U3P_IP_PW_CTRL0	(SSUSB_SIFSLV_IPPC_BASE + 0x0000)
> > +#define CTRL0_IP_SW_RST	(0x1 << 0)
> > +
> > +#define U3P_IP_PW_CTRL1	(SSUSB_SIFSLV_IPPC_BASE + 0x0004)
> > +#define CTRL1_IP_HOST_PDN	(0x1 << 0)
> > +
> > +#define U3P_IP_PW_CTRL2	(SSUSB_SIFSLV_IPPC_BASE + 0x0008)
> > +#define CTRL2_IP_DEV_PDN	(0x1 << 0)
> > +
> > +#define U3P_IP_PW_STS1	(SSUSB_SIFSLV_IPPC_BASE + 0x0010)
> > +#define STS1_IP_SLEEP_STS	(0x1 << 30)
> > +#define STS1_U3_MAC_RST		(0x1 << 16)
> > +#define STS1_SYS125_RST		(0x1 << 10)
> > +#define STS1_REF_RST		(0x1 << 8)
> > +#define STS1_SYSPLL_STABLE	(0x1 << 0)
> > +
> > +#define U3P_IP_PW_STS2	(SSUSB_SIFSLV_IPPC_BASE + 0x0014)
> > +#define STS2_U2_MAC_RST	(0x1 << 0)
> > +
> > +#define U3P_IP_XHCI_CAP	(SSUSB_SIFSLV_IPPC_BASE + 0x0024)
> > +#define CAP_U3_PORT_NUM(p)	((p) & 0xff)
> > +#define CAP_U2_PORT_NUM(p)	(((p) >> 8) & 0xff)
> > +
> > +#define U3P_U3_CTRL_0P	(SSUSB_SIFSLV_IPPC_BASE + 0x0030)
> > +#define CTRL_U3_PORT_HOST_SEL	(0x1 << 2)
> > +#define CTRL_U3_PORT_PDN	(0x1 << 1)
> > +#define CTRL_U3_PORT_DIS	(0x1 << 0)
> > +
> > +#define U3P_U2_CTRL_0P	(SSUSB_SIFSLV_IPPC_BASE + 0x0050)
> > +#define CTRL_U2_PORT_HOST_SEL	(0x1 << 2)
> > +#define CTRL_U2_PORT_PDN	(0x1 << 1)
> > +#define CTRL_U2_PORT_DIS	(0x1 << 0)
> > +
> > +#define U3P_U3_CTRL(p)	(U3P_U3_CTRL_0P + ((p) * 0x08))
> > +#define U3P_U2_CTRL(p)	(U3P_U2_CTRL_0P + ((p) * 0x08))
> > +
> > +#define U3P_USBPHYACR0	(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0000)
> > +#define PA0_RG_U2PLL_FORCE_ON	(0x1 << 15)
> > +
> > +#define U3P_USBPHYACR2	(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0008)
> > +#define PA2_RG_SIF_U2PLL_FORCE_EN	(0x1 << 18)
> > +
> > +#define U3P_USBPHYACR5	(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0014)
> > +#define PA5_RG_U2_HSTX_SRCTRL		(0x7 << 12)
> > +#define PA5_RG_U2_HSTX_SRCTRL_VAL(x)	((0x7 & (x)) << 12)
> > +#define PA5_RG_U2_HS_100U_U3_EN		(0x1 << 11)
> > +
> > +#define U3P_USBPHYACR6	(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0018)
> > +#define PA6_RG_U2_ISO_EN		(0x1 << 31)
> > +#define PA6_RG_U2_BC11_SW_EN	(0x1 << 23)
> > +#define PA6_RG_U2_OTG_VBUSCMP_EN	(0x1 << 20)
> > +
> > +#define U3P_U2PHYACR4	(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0020)
> > +#define P2C_RG_USB20_GPIO_CTL	(0x1 << 9)
> > +#define P2C_USB20_GPIO_MODE	(0x1 << 8)
> > +#define P2C_U2_GPIO_CTR_MSK	(P2C_RG_USB20_GPIO_CTL | P2C_USB20_GPIO_MODE)
> > +
> > +#define U3D_U2PHYDCR0	(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0060)
> > +#define P2C_RG_SIF_U2PLL_FORCE_ON	(0x1 << 24)
> > +
> > +#define U3P_U2PHYDTM0	(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x0068)
> > +#define P2C_FORCE_UART_EN	(0x1 << 26)
> > +#define P2C_FORCE_DATAIN	(0x1 << 23)
> > +#define P2C_FORCE_DM_PULLDOWN	(0x1 << 21)
> > +#define P2C_FORCE_DP_PULLDOWN	(0x1 << 20)
> > +#define P2C_FORCE_XCVRSEL	(0x1 << 19)
> > +#define P2C_FORCE_SUSPENDM	(0x1 << 18)
> > +#define P2C_FORCE_TERMSEL	(0x1 << 17)
> > +#define P2C_RG_DATAIN		(0xf << 10)
> > +#define P2C_RG_DATAIN_VAL(x)	((0xf & (x)) << 10)
> > +#define P2C_RG_DMPULLDOWN	(0x1 << 7)
> > +#define P2C_RG_DPPULLDOWN	(0x1 << 6)
> > +#define P2C_RG_XCVRSEL		(0x3 << 4)
> > +#define P2C_RG_XCVRSEL_VAL(x)	((0x3 & (x)) << 4)
> > +#define P2C_RG_SUSPENDM		(0x1 << 3)
> > +#define P2C_RG_TERMSEL		(0x1 << 2)
> > +#define P2C_DTM0_PART_MASK \
> > +		(P2C_FORCE_DATAIN | P2C_FORCE_DM_PULLDOWN | \
> > +		P2C_FORCE_DP_PULLDOWN | P2C_FORCE_XCVRSEL | \
> > +		P2C_FORCE_TERMSEL | P2C_RG_DMPULLDOWN | \
> > +		P2C_RG_DPPULLDOWN | P2C_RG_TERMSEL)
> > +
> > +#define U3P_U2PHYDTM1	(SSUSB_SIFSLV_U2PHY_COM_BASE + 0x006C)
> > +#define P2C_RG_UART_EN		(0x1 << 16)
> > +#define P2C_RG_VBUSVALID	(0x1 << 5)
> > +#define P2C_RG_SESSEND		(0x1 << 4)
> > +#define P2C_RG_AVALID		(0x1 << 2)
> > +
> > +#define U3P_U3_PHYA_REG0	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0000)
> > +#define P3A_RG_U3_VUSB10_ON	(1 << 5)
> > +
> > +#define U3P_U3_PHYA_REG6	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0018)
> > +#define P3A_RG_TX_EIDLE_CM	(0xf << 28)
> > +#define P3A_RG_TX_EIDLE_CM_VAL(x)	((0xf & (x)) << 28)
> > +
> > +#define U3P_U3_PHYA_REG9	(SSUSB_USB30_PHYA_SIV_B_BASE + 0x0024)
> > +#define P3A_RG_RX_DAC_MUX	(0x1f << 1)
> > +#define P3A_RG_RX_DAC_MUX_VAL(x)	((0x1f & (x)) << 1)
> > +
> > +#define U3P_U3PHYA_DA_REG0	(SSUSB_SIFSLV_U3PHYA_DA_BASE + 0x0)
> > +#define P3A_RG_XTAL_EXT_EN_U3	(0x3 << 10)
> > +#define P3A_RG_XTAL_EXT_EN_U3_VAL(x)	((0x3 & (x)) << 10)
> > +
> > +#define U3P_PHYD_CDR1	(SSUSB_SIFSLV_U3PHYD_BASE + 0x5c)
> > +#define P3D_RG_CDR_BIR_LTD1		(0x1f << 24)
> > +#define P3D_RG_CDR_BIR_LTD1_VAL(x)	((0x1f & (x)) << 24)
> > +#define P3D_RG_CDR_BIR_LTD0		(0x1f << 8)
> > +#define P3D_RG_CDR_BIR_LTD0_VAL(x)	((0x1f & (x)) << 8)
> > +
> > +#define U3P_XTALCTL3		(SSUSB_SIFSLV_SPLLC + 0x18)
> > +#define XC3_RG_U3_XTAL_RX_PWD		(0x1 << 9)
> > +#define XC3_RG_U3_FRC_XTAL_RX_PWD	(0x1 << 8)
> > +
> > +#define U3P_UX_EXIT_LFPS_PARAM	(SSUSB_USB3_MAC_CSR_BASE + 0x00A0)
> > +#define RX_UX_EXIT_REF		(0xff << 8)
> > +#define RX_UX_EXIT_REF_VAL	(0x3 << 8)
> > +
> > +#define U3P_REF_CLK_PARAM	(SSUSB_USB3_MAC_CSR_BASE + 0x00B0)
> > +#define REF_CLK_1000NS		(0xff << 0)
> > +#define REF_CLK_VAL_DEF		(0xa << 0)
> > +
> > +#define U3P_LINK_PM_TIMER	(SSUSB_USB3_SYS_CSR_BASE + 0x0208)
> > +#define PM_LC_TIMEOUT		(0xf << 0)
> > +#define PM_LC_TIMEOUT_VAL	(0x3 << 0)
> > +
> > +#define U3P_TIMING_PULSE_CTRL	(SSUSB_USB3_SYS_CSR_BASE + 0x02B4)
> > +#define U3T_CNT_1US			(0xff << 0)
> > +#define U3T_CNT_1US_VAL		(0x3f << 0)	/* 62.5MHz: 63 */
> > +
> > +#define U3P_U2_TIMING_PARAM	(SSUSB_USB2_CSR_BASE + 0x0040)
> > +#define U2T_VAL_1US		(0xff << 0)
> > +#define U2T_VAL_1US_VAL	(0x3f << 0)	/* 62.5MHz: 63 */
> > +
> > +
> > +#define PERI_WK_CTRL0		0x400
> > +#define UWK_CTL1_1P_LS_E	(0x1 << 0)
> > +#define UWK_CTL1_1P_LS_C(x)	(((x) & 0xf) << 1)
> > +#define UWK_CTR0_0P_LS_NE	(0x1 << 7)  /* negedge for 0p linestate*/
> > +#define UWK_CTR0_0P_LS_PE	(0x1 << 8)  /* posedge */
> > +
> > +#define PERI_WK_CTRL1		0x404
> > +#define UWK_CTL1_IS_P		(0x1 << 6)  /* polarity for ip sleep */
> > +#define UWK_CTL1_0P_LS_P	(0x1 << 7)
> > +#define UWK_CTL1_IDDIG_P	(0x1 << 9)  /* polarity */
> > +#define UWK_CTL1_IDDIG_E	(0x1 << 10) /* enable debounce */
> > +#define UWK_CTL1_IDDIG_C(x)	(((x) & 0xf) << 11)  /* cycle debounce */
> > +#define UWK_CTL1_0P_LS_E	(0x1 << 20)
> > +#define UWK_CTL1_0P_LS_C(x)	(((x) & 0xf) << 21)
> > +#define UWK_CTL1_IS_E		(0x1 << 25)
> > +#define UWK_CTL1_IS_C(x)	(((x) & 0xf) << 26)
> > +
> > +enum ssusb_wakeup_src {
> > +	SSUSB_WK_IP_SLEEP = 1,
> > +	SSUSB_WK_LINE_STATE = 2,
> > +};
> > +
> > +struct mt65xx_u3phy {
> > +	struct usb_phy phy;
> > +	struct device *dev;
> > +	void __iomem *mac_base;	/* only device-mac regs, exclude xhci's */
> > +	void __iomem *sif_base;	/* include sif & sif2 */
> > +	struct regmap *pericfg;
> > +	struct clk *wk_deb_p0;	/* port0's wakeup debounce clock */
> > +	struct clk *wk_deb_p1;
> > +	struct clk *u3phya_ref;	/* reference clock of usb3 anolog phy */
> > +	int wakeup_src;
> > +	int u2port_num;
> > +};
> > +
> > +
> > +static void u3p_writel(void __iomem *base, u32 offset, u32 data)
> > +{
> > +	writel(data, base + offset);
> > +}
> 
> Never ever name a function 'writel' that has the arguments reversed to
> the original writel function.
> 
Remove it later

> > +
> > +static u32 u3p_readl(void __iomem *base, u32 offset)
> > +{
> > +	return readl(base + offset);
> > +}
> > +
> > +static void u3p_setmsk(void __iomem *base, u32 offset, u32 msk)
> > +{
> > +	void __iomem *addr = base + offset;
> > +
> > +	writel((readl(addr) | msk), addr);
> > +}
> > +
> > +static void u3p_clrmsk(void __iomem *base, u32 offset, u32 msk)
> > +{
> > +	void __iomem *addr = base + offset;
> > +
> > +	writel((readl(addr) & ~msk), addr);
> > +}
> > +
> > +static void u3p_setval(void __iomem *base, u32 offset,
> > +	u32 mask, u32 value)
> > +{
> > +	void __iomem *addr = base + offset;
> > +	unsigned int new_value;
> > +
> > +	new_value = (readl(addr) & ~mask) | value;
> > +	writel(new_value, addr);
> > +}
> > +
> > +static void phy_index_power_on(struct mt65xx_u3phy *u3phy, int index)
> > +{
> > +	void __iomem *sif_base = u3phy->sif_base + U3P_PHY_BASE(index);
> > +
> > +	if (!index) {
> > +		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
> > +		u3p_setmsk(sif_base, U3P_U3_PHYA_REG0, P3A_RG_U3_VUSB10_ON);
> > +		/* power domain iso disable */
> > +		u3p_clrmsk(sif_base, U3P_USBPHYACR6, PA6_RG_U2_ISO_EN);
> > +	}
> > +
> > +	/* switch to USB function. (system register, force ip into usb mode) */
> > +	u3p_clrmsk(sif_base, U3P_U2PHYDTM0, P2C_FORCE_UART_EN);
> > +	u3p_clrmsk(sif_base, U3P_U2PHYDTM1, P2C_RG_UART_EN);
> > +	if (!index)
> > +		u3p_clrmsk(sif_base, U3P_U2PHYACR4, P2C_U2_GPIO_CTR_MSK);
> > +
> > +	/* (force_suspendm=0) (let suspendm=1, enable usb 480MHz pll) */
> > +	u3p_clrmsk(sif_base, U3P_U2PHYDTM0, P2C_FORCE_SUSPENDM);
> > +	u3p_clrmsk(sif_base, U3P_U2PHYDTM0,
> > +			P2C_RG_XCVRSEL | P2C_RG_DATAIN | P2C_DTM0_PART_MASK);
> > +
> > +	/* DP/DM BC1.1 path Disable */
> > +	u3p_clrmsk(sif_base, U3P_USBPHYACR6, PA6_RG_U2_BC11_SW_EN);
> > +	/* OTG Enable */
> > +	u3p_setmsk(sif_base, U3P_USBPHYACR6, PA6_RG_U2_OTG_VBUSCMP_EN);
> > +	u3p_setval(sif_base, U3P_U3PHYA_DA_REG0, P3A_RG_XTAL_EXT_EN_U3,
> > +			P3A_RG_XTAL_EXT_EN_U3_VAL(2));
> > +	u3p_setval(sif_base, U3P_U3_PHYA_REG9, P3A_RG_RX_DAC_MUX,
> > +			P3A_RG_RX_DAC_MUX_VAL(4));
> > +
> > +	if (!index) {
> > +		u3p_setmsk(sif_base, U3P_XTALCTL3, XC3_RG_U3_XTAL_RX_PWD);
> > +		u3p_setmsk(sif_base, U3P_XTALCTL3, XC3_RG_U3_FRC_XTAL_RX_PWD);
> > +		/* [mt8173]disable Change 100uA current from SSUSB */
> > +		u3p_clrmsk(sif_base, U3P_USBPHYACR5, PA5_RG_U2_HS_100U_U3_EN);
> > +	}
> > +	u3p_setval(sif_base, U3P_U3_PHYA_REG6, P3A_RG_TX_EIDLE_CM,
> > +			P3A_RG_TX_EIDLE_CM_VAL(0xe));
> > +	u3p_setval(sif_base, U3P_PHYD_CDR1, P3D_RG_CDR_BIR_LTD0,
> > +			P3D_RG_CDR_BIR_LTD0_VAL(0xc));
> > +	u3p_setval(sif_base, U3P_PHYD_CDR1, P3D_RG_CDR_BIR_LTD1,
> > +			P3D_RG_CDR_BIR_LTD1_VAL(0x3));
> > +
> > +	udelay(800);
> > +	u3p_setmsk(sif_base, U3P_U2PHYDTM1, P2C_RG_VBUSVALID | P2C_RG_AVALID);
> > +	u3p_clrmsk(sif_base, U3P_U2PHYDTM1, P2C_RG_SESSEND);
> > +
> > +	/* USB 2.0 slew rate calibration */
> > +	u3p_setval(sif_base, U3P_USBPHYACR5, PA5_RG_U2_HSTX_SRCTRL,
> > +			PA5_RG_U2_HSTX_SRCTRL_VAL(4));
> > +
> > +	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
> > +}
> > +
> > +static void phy_index_power_off(struct mt65xx_u3phy *u3phy, int index)
> > +{
> > +	void __iomem *sif_base = u3phy->sif_base + U3P_PHY_BASE(index);
> > +
> > +	/* switch to USB function. (system register, force ip into usb mode) */
> > +	u3p_clrmsk(sif_base, U3P_U2PHYDTM0, P2C_FORCE_UART_EN);
> > +	u3p_clrmsk(sif_base, U3P_U2PHYDTM1, P2C_RG_UART_EN);
> 
> That's the same register sequence as above in power_on. Do you really
> need to do this twice or is this more something that should be done
> during initialization once?
> 
I will put them into init function

> > +	if (!index)
> > +		u3p_clrmsk(sif_base, U3P_U2PHYACR4, P2C_U2_GPIO_CTR_MSK);
> > +
> > +	u3p_setmsk(sif_base, U3P_U2PHYDTM0, P2C_FORCE_SUSPENDM);
> > +	u3p_setval(sif_base, U3P_U2PHYDTM0,
> > +			P2C_RG_XCVRSEL, P2C_RG_XCVRSEL_VAL(1));
> > +	u3p_setval(sif_base, U3P_U2PHYDTM0,
> > +			P2C_RG_DATAIN, P2C_RG_DATAIN_VAL(0));
> > +	u3p_setmsk(sif_base, U3P_U2PHYDTM0, P2C_DTM0_PART_MASK);
> 
> That's four read/write accesses in a row which is really hard to read.
> This should really be something like:
> 
> 	val = readl(sif_base + U3P_U2PHYDTM0);
> 	val &= ~(P2C_RG_XCVRSEL | P2C_RG_DATAIN)
> 	val |= P2C_FORCE_SUSPENDM | P2C_RG_XCVRSEL_VAL(1);
> 	writel(val, sif_base + U3P_U2PHYDTM0);
> 
> Those read/modify/write access functions often have the tendency to lead
> to inefficient code.
> 
Sometimes the bits should be set by sequence, check it later.

> Generally review your register accesses. There are several bits that are
> cleared multiple times but never set, like:
> 
> U3P_U2PHYDTM0, P2C_FORCE_UART_EN -> cleared multiple times, never set
> U3P_USBPHYACR6, PA6_RG_U2_BC11_SW_EN -> cleared mutliple times, never set
> U3P_U2PHYDTM1, P2C_RG_UART_EN -> cleared mutliple times, never set
> 
> This probably belongs to some init code executed once.
> 
OK,

> > +	/* DP/DM BC1.1 path Disable */
> > +	u3p_clrmsk(sif_base, U3P_USBPHYACR6, PA6_RG_U2_BC11_SW_EN);
> > +	/* OTG Disable */
> > +	u3p_clrmsk(sif_base, U3P_USBPHYACR6, PA6_RG_U2_OTG_VBUSCMP_EN);
> > +	if (!index) {
> > +		/* Change 100uA current switch to USB2.0 */
> > +		u3p_clrmsk(sif_base, U3P_USBPHYACR5, PA5_RG_U2_HS_100U_U3_EN);
> > +	}
> > +	udelay(800);
> > +
> > +	/* let suspendm=0, set utmi into analog power down */
> > +	u3p_clrmsk(sif_base, U3P_U2PHYDTM0, P2C_RG_SUSPENDM);
> > +	udelay(1);
> > +
> > +	u3p_clrmsk(sif_base, U3P_U2PHYDTM1, P2C_RG_VBUSVALID | P2C_RG_AVALID);
> > +	u3p_setmsk(sif_base, U3P_U2PHYDTM1, P2C_RG_SESSEND);
> > +	if (!index) {
> > +		/* Set RG_SSUSB_VUSB10_ON as 1 after VUSB10 ready */
> > +		u3p_clrmsk(sif_base, U3P_U3_PHYA_REG0, P3A_RG_U3_VUSB10_ON);
> > +	}
> > +	dev_dbg(u3phy->dev, "%s(%d)\n", __func__, index);
> > +}
> > +
> > +static void u3phy_power_on(struct mt65xx_u3phy *u3phy)
> > +{
> > +	phy_index_power_on(u3phy, 0);
> > +	if (u3phy->u2port_num > 1)
> > +		phy_index_power_on(u3phy, 1);
> > +}
> > +
> > +static void u3phy_power_off(struct mt65xx_u3phy *u3phy)
> > +{
> > +	phy_index_power_off(u3phy, 0);
> > +	if (u3phy->u2port_num > 1)
> > +		phy_index_power_off(u3phy, 1);
> > +}
> > +
> > +static int check_ip_clk_status(struct mt65xx_u3phy *u3phy)
> > +{
> > +	int ret;
> > +	int u3_port_num;
> > +	int u2_port_num;
> > +	u32 xhci_cap;
> > +	u32 val;
> > +	void __iomem *sif_base = u3phy->sif_base;
> > +
> > +	xhci_cap = u3p_readl(sif_base, U3P_IP_XHCI_CAP);
> > +	u3_port_num = CAP_U3_PORT_NUM(xhci_cap);
> > +	u2_port_num = CAP_U2_PORT_NUM(xhci_cap);
> > +
> > +	ret = readl_poll_timeout(sif_base + U3P_IP_PW_STS1, val,
> > +			  (val & STS1_SYSPLL_STABLE), 100, 10000);
> > +	if (ret) {
> > +		dev_err(u3phy->dev, "sypll is not stable!!!\n");
> > +		return ret;
> > +	}
> > +
> > +	ret = eadl_poll_timeout(sif_base + U3P_IP_PW_STS1, val,
> > +			  (val & STS1_REF_RST), 100, 10000);
> > +	if (ret) {
> > +		dev_err(u3phy->dev, "ref_clk is still active!!!\n");
> > +		return ret;
> > +	}
> > +
> > +	ret = readl_poll_timeout(sif_base + U3P_IP_PW_STS1, val,
> > +			   (val & STS1_SYS125_RST), 100, 10000);
> > +	if (ret) {
> > +		dev_err(u3phy->dev, "sys125_ck is still active!!!\n");
> > +		return ret;
> > +	}
> > +
> > +	if (u3_port_num) {
> > +		ret = readl_poll_timeout(sif_base + U3P_IP_PW_STS1, val,
> > +				   (val & STS1_U3_MAC_RST), 100, 10000);
> > +		if (ret) {
> > +			dev_err(u3phy->dev, "mac3_mac_ck is still active!!!\n");
> > +			return ret;
> > +		}
> > +	}
> > +
> > +	if (u2_port_num) {
> > +		ret = readl_poll_timeout(sif_base + U3P_IP_PW_STS2, val,
> > +				   (val & STS2_U2_MAC_RST), 100, 10000);
> > +		if (ret) {
> > +			dev_err(u3phy->dev, "mac2_sys_ck is still active!!!\n");
> > +			return ret;
> > +		}
> > +	}
> > +
> > +	return 0;
> > +}
> > +
> > +static int u3phy_ports_enable(struct mt65xx_u3phy *u3phy)
> > +{
> > +	int i;
> > +	u32 temp;
> > +	int u3_port_num;
> > +	int u2_port_num;
> > +	void __iomem *sif_base = u3phy->sif_base;
> > +
> > +	temp = u3p_readl(sif_base, U3P_IP_XHCI_CAP);
> > +	u3_port_num = CAP_U3_PORT_NUM(temp);
> > +	u2_port_num = CAP_U2_PORT_NUM(temp);
> > +	dev_dbg(u3phy->dev, "%s u2p:%d, u3p:%d\n",
> > +		__func__, u2_port_num, u3_port_num);
> > +
> > +	/* power on host ip */
> > +	u3p_clrmsk(sif_base, U3P_IP_PW_CTRL1, CTRL1_IP_HOST_PDN);
> > +
> > +	/* power on and enable all u3 ports */
> > +	for (i = 0; i < u3_port_num; i++) {
> > +		temp = u3p_readl(sif_base, U3P_U3_CTRL(i));
> > +		temp &= ~(CTRL_U3_PORT_PDN | CTRL_U3_PORT_DIS);
> > +		temp |= CTRL_U3_PORT_HOST_SEL;
> > +		u3p_writel(sif_base, U3P_U3_CTRL(i), temp);
> > +	}
> > +
> > +	/* power on and enable all u2 ports */
> > +	for (i = 0; i < u2_port_num; i++) {
> > +		temp = u3p_readl(sif_base, U3P_U2_CTRL(i));
> > +		temp &= ~(CTRL_U2_PORT_PDN | CTRL_U2_PORT_DIS);
> > +		temp |= CTRL_U2_PORT_HOST_SEL;
> > +		u3p_writel(sif_base, U3P_U2_CTRL(i), temp);
> > +	}
> > +	return check_ip_clk_status(u3phy);
> > +}
> > +
> > +static int u3phy_ports_disable(struct mt65xx_u3phy *u3phy)
> > +{
> > +	int i;
> > +	u32 temp;
> > +	int ret;
> > +	int u3_port_num;
> > +	int u2_port_num;
> > +	void __iomem *sif_base = u3phy->sif_base;
> > +
> > +	temp = u3p_readl(sif_base, U3P_IP_XHCI_CAP);
> > +	u3_port_num = CAP_U3_PORT_NUM(temp);
> > +	u2_port_num = CAP_U2_PORT_NUM(temp);
> > +	dev_dbg(u3phy->dev, "%s u2p:%d, u3p:%d\n",
> > +		__func__, u2_port_num, u3_port_num);
> > +
> > +	/* power on and enable all u3 ports */
> 
> This comment seems wrong.
> 
Yes, It is my mistake 

> > +	for (i = 0; i < u3_port_num; i++) {
> > +		temp = u3p_readl(sif_base, U3P_U3_CTRL(i));
> > +		temp |= CTRL_U3_PORT_PDN;
> > +		u3p_writel(sif_base, U3P_U3_CTRL(i), temp);
> > +	}
> > +
> > +	/* power on and enable all u2 ports */
> 
> ditto
> 
> > +	for (i = 0; i < u2_port_num; i++) {
> > +		temp = u3p_readl(sif_base, U3P_U2_CTRL(i));
> > +		temp |= CTRL_U2_PORT_PDN;
> > +		u3p_writel(sif_base, U3P_U2_CTRL(i), temp);
> > +	}
> > +
> > +	/* power off host ip */
> > +	u3p_setmsk(sif_base, U3P_IP_PW_CTRL1, CTRL1_IP_HOST_PDN);
> > +	u3p_setmsk(sif_base, U3P_IP_PW_CTRL2, CTRL2_IP_DEV_PDN);
> > +
> > +	ret = readl_poll_timeout(sif_base + U3P_IP_PW_STS1, temp,
> > +			  (temp & STS1_IP_SLEEP_STS), 100, 100000);
> > +	if (ret) {
> > +		dev_err(u3phy->dev, "ip sleep failed!!!\n");
> > +		return ret;
> > +	}
> > +	return 0;
> > +}
> > +
> > +static void u3phy_timing_init(struct mt65xx_u3phy *u3phy)
> > +{
> > +	void __iomem *mbase = u3phy->mac_base;
> > +	int u3_port_num;
> > +	u32 temp;
> > +
> > +	temp = u3p_readl(u3phy->sif_base, U3P_IP_XHCI_CAP);
> > +	u3_port_num = CAP_U3_PORT_NUM(temp);
> > +
> > +	if (u3_port_num) {
> > +		/* set MAC reference clock speed */
> > +		u3p_setval(mbase, U3P_UX_EXIT_LFPS_PARAM,
> > +				RX_UX_EXIT_REF, RX_UX_EXIT_REF_VAL);
> > +		/* set REF_CLK */
> > +		u3p_setval(mbase, U3P_REF_CLK_PARAM,
> > +				REF_CLK_1000NS, REF_CLK_VAL_DEF);
> > +		/* set SYS_CLK */
> > +		u3p_setval(mbase, U3P_TIMING_PULSE_CTRL,
> > +				U3T_CNT_1US, U3T_CNT_1US_VAL);
> > +		/* set LINK_PM_TIMER=3 */
> > +		u3p_setval(mbase, U3P_LINK_PM_TIMER,
> > +				PM_LC_TIMEOUT, PM_LC_TIMEOUT_VAL);
> 
> This fiddles in the register space of the xhci controller. Should be
> done in the xhci driver, not here in the phy driver.
> 
done

> > +	}
> > +	u3p_setval(mbase, U3P_U2_TIMING_PARAM, U2T_VAL_1US, U2T_VAL_1US_VAL);
> > +}
> > +
> > +static int u3phy_clks_enable(struct mt65xx_u3phy *u3phy)
> > +{
> > +	int ret;
> > +
> > +	ret = clk_prepare_enable(u3phy->u3phya_ref);
> > +	if (ret) {
> > +		dev_err(u3phy->dev, "failed to enable u3phya_ref\n");
> > +		goto u3phya_ref_err;
> > +	}
> > +	ret = clk_prepare_enable(u3phy->wk_deb_p0);
> > +	if (ret) {
> > +		dev_err(u3phy->dev, "failed to enable wk_deb_p0\n");
> > +		goto usb_p0_err;
> > +	}
> > +	if (u3phy->u2port_num > 1) {
> > +		ret = clk_prepare_enable(u3phy->wk_deb_p1);
> > +		if (ret) {
> > +			dev_err(u3phy->dev, "failed to enable wk_deb_p1\n");
> > +			goto usb_p1_err;
> > +		}
> > +	}
> > +	udelay(50);
> > +
> > +	return 0;
> > +
> > +usb_p1_err:
> > +	clk_disable_unprepare(u3phy->wk_deb_p0);
> > +usb_p0_err:
> > +	clk_disable_unprepare(u3phy->u3phya_ref);
> > +u3phya_ref_err:
> > +	return -EINVAL;
> > +}
> > +
> > +static void u3phy_clks_disable(struct mt65xx_u3phy *u3phy)
> > +{
> > +	if (u3phy->u2port_num > 1)
> > +		clk_disable_unprepare(u3phy->wk_deb_p1);
> > +	clk_disable_unprepare(u3phy->wk_deb_p0);
> > +	clk_disable_unprepare(u3phy->u3phya_ref);
> > +}
> > +
> > +/* only clocks can be turn off for ip-sleep wakeup mode */
> > +static void usb_wakeup_ip_sleep_en(struct mt65xx_u3phy *u3phy)
> > +{
> > +	u32 tmp;
> > +	struct regmap *pericfg = u3phy->pericfg;
> > +
> > +	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
> > +	tmp &= ~UWK_CTL1_IS_P;
> > +	tmp &= ~(UWK_CTL1_IS_C(0xf));
> > +	tmp |= UWK_CTL1_IS_C(0x8);
> > +	regmap_write(pericfg, PERI_WK_CTRL1, tmp);
> > +	regmap_write(pericfg, PERI_WK_CTRL1, tmp | UWK_CTL1_IS_E);
> > +
> > +	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
> > +	dev_dbg(u3phy->dev, "%s(): WK_CTRL1[P6,E25,C26:29]=%#x\n", __func__,
> > +		tmp);
> > +}
> > +
> > +static void usb_wakeup_ip_sleep_dis(struct mt65xx_u3phy *u3phy)
> > +{
> > +	u32 tmp;
> > +
> > +	regmap_read(u3phy->pericfg, PERI_WK_CTRL1, &tmp);
> > +	tmp &= ~UWK_CTL1_IS_E;
> > +	regmap_write(u3phy->pericfg, PERI_WK_CTRL1, tmp);
> > +}
> > +
> > +/*
> > +* for line-state wakeup mode, phy's power should not power-down
> > +* and only support cable plug in/out
> > +*/
> > +static void usb_wakeup_line_state_en(struct mt65xx_u3phy *u3phy)
> > +{
> > +	u32 tmp;
> > +	struct regmap *pericfg = u3phy->pericfg;
> > +
> > +	/* line-state of u2-port0 */
> > +	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
> > +	tmp &= ~UWK_CTL1_0P_LS_P;
> > +	tmp &= ~(UWK_CTL1_0P_LS_C(0xf));
> > +	tmp |= UWK_CTL1_0P_LS_C(0x8);
> > +	regmap_write(pericfg, PERI_WK_CTRL1, tmp);
> > +	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
> > +	regmap_write(pericfg, PERI_WK_CTRL1, tmp | UWK_CTL1_0P_LS_E);
> > +
> > +	/* line-state of u2-port1 if support */
> > +	if (u3phy->u2port_num > 1) {
> > +		regmap_read(pericfg, PERI_WK_CTRL0, &tmp);
> > +		tmp &= ~(UWK_CTL1_1P_LS_C(0xf));
> > +		tmp |= UWK_CTL1_1P_LS_C(0x8);
> > +		regmap_write(pericfg, PERI_WK_CTRL0, tmp);
> > +		regmap_write(pericfg, PERI_WK_CTRL0, tmp | UWK_CTL1_1P_LS_E);
> > +	}
> > +}
> > +
> > +static void usb_wakeup_line_state_dis(struct mt65xx_u3phy *u3phy)
> > +{
> > +	u32 tmp;
> > +	struct regmap *pericfg = u3phy->pericfg;
> > +
> > +	regmap_read(pericfg, PERI_WK_CTRL1, &tmp);
> > +	tmp &= ~UWK_CTL1_0P_LS_E;
> > +	regmap_write(pericfg, PERI_WK_CTRL1, tmp);
> > +
> > +	if (u3phy->u2port_num > 1) {
> > +		regmap_read(pericfg, PERI_WK_CTRL0, &tmp);
> > +		tmp &= ~UWK_CTL1_1P_LS_E;
> > +		regmap_write(pericfg, PERI_WK_CTRL0, tmp);
> > +	}
> > +}
> > +
> > +static void usb_wakeup_enable(struct mt65xx_u3phy *u3phy)
> > +{
> > +	if (u3phy->wakeup_src == SSUSB_WK_IP_SLEEP)
> > +		usb_wakeup_ip_sleep_en(u3phy);
> > +	else if (u3phy->wakeup_src == SSUSB_WK_LINE_STATE)
> > +		usb_wakeup_line_state_en(u3phy);
> > +}
> > +
> > +static void usb_wakeup_disable(struct mt65xx_u3phy *u3phy)
> > +{
> > +	if (u3phy->wakeup_src == SSUSB_WK_IP_SLEEP)
> > +		usb_wakeup_ip_sleep_dis(u3phy);
> > +	else if (u3phy->wakeup_src == SSUSB_WK_LINE_STATE)
> > +		usb_wakeup_line_state_dis(u3phy);
> > +}
> > +
> > +static int mt65xx_u3phy_init(struct usb_phy *phy)
> > +{
> > +	struct mt65xx_u3phy *u3phy;
> > +	int ret;
> > +
> > +	u3phy = container_of(phy, struct mt65xx_u3phy, phy);
> > +	dev_dbg(u3phy->dev, "%s+\n", __func__);
> > +
> > +	ret = pm_runtime_get_sync(u3phy->dev);
> > +	if (ret < 0)
> > +		goto pm_err;
> > +
> > +	ret = u3phy_clks_enable(u3phy);
> > +	if (ret) {
> > +		dev_err(u3phy->dev, "failed to enable clks\n");
> > +		goto clks_err;
> > +	}
> > +
> > +	/* reset whole ip */
> > +	u3p_setmsk(u3phy->sif_base, U3P_IP_PW_CTRL0, CTRL0_IP_SW_RST);
> > +	u3p_clrmsk(u3phy->sif_base, U3P_IP_PW_CTRL0, CTRL0_IP_SW_RST);
> > +
> > +	ret = u3phy_ports_enable(u3phy);
> > +	if (ret) {
> > +		dev_err(u3phy->dev, "failed to enable ports\n");
> > +		goto port_err;
> > +	}
> > +	u3phy_timing_init(u3phy);
> > +	u3phy_power_on(u3phy);
> > +	msleep(40);
> > +
> > +	return 0;
> > +
> > +port_err:
> > +	u3phy_clks_disable(u3phy);
> > +clks_err:
> > +	pm_runtime_put_sync(u3phy->dev);
> > +pm_err:
> > +	return ret;
> > +}
> > +
> > +
> > +static void mt65xx_u3phy_shutdown(struct usb_phy *phy)
> > +{
> > +	struct mt65xx_u3phy *u3phy;
> > +
> > +	u3phy = container_of(phy, struct mt65xx_u3phy, phy);
> > +	u3phy_power_off(u3phy);
> > +	u3phy_clks_disable(u3phy);
> > +	pm_runtime_put_sync(u3phy->dev);
> > +}
> > +
> > +
> > +static int mt65xx_u3phy_suspend(struct usb_phy *x, int suspend)
> > +{
> > +	struct mt65xx_u3phy *u3phy = container_of(x, struct mt65xx_u3phy, phy);
> > +
> > +	if (suspend) {
> > +		u3phy_ports_disable(u3phy);
> > +		u3phy_power_off(u3phy);
> > +		u3phy_clks_disable(u3phy);
> > +		usb_wakeup_enable(u3phy);
> > +	} else {
> > +		usb_wakeup_disable(u3phy);
> > +		u3phy_clks_enable(u3phy);
> > +		u3phy_power_on(u3phy);
> > +		u3phy_ports_enable(u3phy);
> > +	}
> > +	return 0;
> > +}
> > +
> > +
> > +static const struct of_device_id mt65xx_u3phy_id_table[] = {
> > +	{ .compatible = "mediatek,mt8173-u3phy",},
> > +	{ },
> > +};
> > +MODULE_DEVICE_TABLE(of, mt65xx_u3phy_id_table);
> > +
> > +
> > +static int mt65xx_u3phy_probe(struct platform_device *pdev)
> > +{
> > +	struct device *dev = &pdev->dev;
> > +	struct device_node *np = dev->of_node;
> > +	struct resource *mac_res;
> > +	struct resource *sif_res;
> > +	struct mt65xx_u3phy *u3phy;
> > +	int retval = -ENOMEM;
> > +
> > +	u3phy = devm_kzalloc(&pdev->dev, sizeof(*u3phy), GFP_KERNEL);
> > +	if (!u3phy)
> > +		goto err;
> 
> No need for goto if all you do there is to return. return here.

Ok, I will revise it 

Thank you very much.
> 
> Sascha
> 
> 


--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux