On Wed, Jul 01, 2015 at 01:20:18PM +0100, Lee Jones wrote: > On Fri, 26 Jun 2015, Yi Zhang wrote: > > On Thu, Jun 25, 2015 at 09:32:48AM +0100, Lee Jones wrote: > > > On Fri, 12 Jun 2015, Yi Zhang wrote: > > > > > > > 88pm886 and 88pm880 are combo PMIC chip, which integrates > > > > regulator, onkey, rtc, gpadc, charger, fuelgauge function; > > > > > > > > this patch add the basic support for them, adding related resource, such as > > > > interrupt, preparing for the client-device driver > > > > > > > > Signed-off-by: Yi Zhang <yizhang@xxxxxxxxxxx> > > > > --- > > > > drivers/mfd/88pm880-table.c | 173 ++++++++++++ > > > > drivers/mfd/88pm886-table.c | 173 ++++++++++++ > > > > drivers/mfd/88pm88x-core.c | 584 ++++++++++++++++++++++++++++++++++++++++ > > > > drivers/mfd/88pm88x-i2c.c | 167 ++++++++++++ > > > > drivers/mfd/88pm88x-irq.c | 171 ++++++++++++ > > > > drivers/mfd/88pm88x.h | 51 ++++ > > > > Thanks very much for your patience on such a long patch, it is my > > fault, I will modify according to your precious comments and split > > them in the next version, thanks very much; > > You are welcome. > > [...] /* Cut 100's of lines where you were agreeing with me */ > > In future, please cut all of the lines that you agree with me and only > leave in the useful or contentious items. Thanks, I need to pay attention to the etiquette, reading such a long mail is absolutly not a good experience, my fault, sorry; > > > > > + chip->ldo_page_addr = client->addr + 1; > > > > + chip->power_page_addr = client->addr + 1; > > > > + chip->gpadc_page_addr = client->addr + 2; > > > > + chip->battery_page_addr = client->addr + 3; > > > > + chip->buck_page_addr = client->addr + 4; > > > > + chip->test_page_addr = client->addr + 7; > > > > > > I have no idea what's going on here, but it's almost certainly not > > > correct. Instead of separating these out per device have a base > > > address and create DEFINES for each of them. > > > > it is because this PMIC has several i2c address, each has different > > function, the offset vesus the client->addr is fixed, the client->addr > > is 0x30 from device tree, then the gpadc_page_addr is 0x32, that is > > why I use client->addr + 2; > > > > you mean the DEFINES are better? > > I do mean that, yes. If you don't want supply nodes for each of the > client devices (what is the reason for that?), then just supply the > base address and use DEFINES to obtain the offsets. I got your point. > > [...] /* Lots more 'yes's removed */ > > > > > + ret = mfd_add_devices(chip->dev, 0, common_cell_devs, > > > > > > What does 0 mean? > > > > I should use -1 here, though it _seems_ works.. > > Please use the pre-allocated platform DEFINEs for them. Clear now; > > [...] > > > > > + for (;;) > > > > + cpu_relax(); > > > > > > What's the point of this? > > > > I just would like to busy loop at the end of the power_off callback; > > Is that when you're meant to do? Why can't you just return? Just return is a good idea, my intention is trying to invoke the user's attention that the power off fails.. > > [...] > > > > > +#define CELL_DEV(_name, _r, _compatible, _id) { \ > > > > + .name = _name, \ > > > > + .of_compatible = _compatible, \ > > > > + .num_resources = ARRAY_SIZE(_r), \ > > > > + .resources = _r, \ > > > > + .id = _id, \ > > > > + } > > > > > > This is not required. > > > > > > If you feel the need for an MFD Cell macro, you probably have too many > > > MFD cells and you have done something wrong.. > > > > Yes, I should use one MFD to cover regulators and one MFD to cover > > LEDs, I will remember this lesson; thanks; > > That wasn't what I was saying. Just remove the MACRO and add the > information into the cells like all the other MFD drivers do. Got your point, I will remove them and clean up the regulator part; thanks; > > [...] > > -- > Lee Jones > Linaro STMicroelectronics Landing Team Lead > Linaro.org │ Open source software for ARM SoCs > Follow Linaro: Facebook | Twitter | Blog -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html