Add support to configure Enhanced Transient Response Enable (ETR)
and Sensitivity Selection based on maximum current i.e. expected
load on that rail.
Maxim recommended as:
- Enable ETR with high sensitivity (75mV/us) for 0 to 9A expected loads,
- Enable ETR with low sensitivity (150mV/us) for 9A to 12A expected loads.
- Disable ETR for expected load > 12A.
These recommendation will be configured for MAX77621 when maximum load
is provided through regulator constraint for maximum current from platform.
Signed-off-by: Laxman Dewangan <ldewangan@xxxxxxxxxx>
---
drivers/regulator/max8973-regulator.c | 52 +++++++++++++++++++++++++++++++++++
1 file changed, 52 insertions(+)
diff --git a/drivers/regulator/max8973-regulator.c b/drivers/regulator/max8973-regulator.c
index a8fd7f4..f673659 100644
--- a/drivers/regulator/max8973-regulator.c
+++ b/drivers/regulator/max8973-regulator.c
@@ -75,6 +75,7 @@
#define MAX8973_DISCH_ENBABLE BIT(5)
#define MAX8973_FT_ENABLE BIT(4)
+#define MAX8973_CKKADV_TRIP_MASK 0xC
#define MAX8973_CKKADV_TRIP_DISABLE 0xC
#define MAX8973_CKKADV_TRIP_75mV_PER_US 0x0
#define MAX8973_CKKADV_TRIP_150mV_PER_US 0x4
@@ -282,6 +283,55 @@ static int max8973_set_ramp_delay(struct regulator_dev *rdev,
return ret;
}
+static int max8973_set_current_limit(struct regulator_dev *rdev,
+ int min_ua, int max_ua)
+{
+ struct max8973_chip *max = rdev_get_drvdata(rdev);
+ unsigned int val;
+ int ret;
+
+ if (max_ua <= 9000000)
+ val = MAX8973_CKKADV_TRIP_75mV_PER_US;
+ else if (max_ua <= 12000000)
+ val = MAX8973_CKKADV_TRIP_150mV_PER_US;
+ else
+ val = MAX8973_CKKADV_TRIP_DISABLE;
+
+ ret = regmap_update_bits(max->regmap, MAX8973_CONTROL2,
+ MAX8973_CKKADV_TRIP_MASK, val);
+ if (ret < 0) {
+ dev_err(max->dev, "register %d update failed: %d\n",
+ MAX8973_CONTROL2, ret);
+ return ret;
+ }
+ return 0;
+}
+
+static int max8973_get_current_limit(struct regulator_dev *rdev)
+{
+ struct max8973_chip *max = rdev_get_drvdata(rdev);
+ unsigned int control2;
+ int ret;
+
+ ret = regmap_read(max->regmap, MAX8973_CONTROL2, &control2);
+ if (ret < 0) {
+ dev_err(max->dev, "register %d read failed: %d\n",
+ MAX8973_CONTROL2, ret);
+ return ret;
+ }
+ switch (control2 & MAX8973_CKKADV_TRIP_MASK) {
+ case MAX8973_CKKADV_TRIP_DISABLE:
+ return 15000000;
+ case MAX8973_CKKADV_TRIP_150mV_PER_US:
+ return 12000000;
+ case MAX8973_CKKADV_TRIP_75mV_PER_US:
+ return 9000000;
+ default:
+ break;
+ }
+ return 9000000;
+}
+
static const struct regulator_ops max8973_dcdc_ops = {
.get_voltage_sel = max8973_dcdc_get_voltage_sel,
.set_voltage_sel = max8973_dcdc_set_voltage_sel,
@@ -632,6 +682,8 @@ static int max8973_probe(struct i2c_client *client,
max->ops.enable = regulator_enable_regmap;
max->ops.disable = regulator_disable_regmap;
max->ops.is_enabled = regulator_is_enabled_regmap;
+ max->ops.set_current_limit = max8973_set_current_limit;
+ max->ops.get_current_limit = max8973_get_current_limit;
break;
default:
break;
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
