Le 11/06/2015 18:20, Cyrille Pitchen a écrit :
> This patch updates macro definitions in atmel_serial.h to fit the
> 80 column rule.
>
> Please note that some deprecated comments such as "[AT91SAM9261 only]"
> are removed as the corresponding bits also exist in some later chips.
>
> The patch also fix macro definitions in atmel_serial.c to replace
> (port,v) by (port, v).
>
> Signed-off-by: Cyrille Pitchen <cyrille.pitchen@xxxxxxxxx>
Acked-by: Nicolas Ferre <nicolas.ferre@xxxxxxxxx>
> ---
> drivers/tty/serial/atmel_serial.c | 52 +++++-----
> include/linux/atmel_serial.h | 204 +++++++++++++++++++-------------------
> 2 files changed, 128 insertions(+), 128 deletions(-)
>
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index 2a8f528..112e74b 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -89,35 +89,35 @@ static void atmel_stop_rx(struct uart_port *port);
> #define ATMEL_ISR_PASS_LIMIT 256
>
> /* UART registers. CR is write-only, hence no GET macro */
> -#define UART_PUT_CR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_CR)
> -#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR)
> -#define UART_PUT_MR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_MR)
> -#define UART_PUT_IER(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IER)
> -#define UART_PUT_IDR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IDR)
> -#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR)
> -#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR)
> -#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR)
> -#define UART_PUT_CHAR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_THR)
> -#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR)
> -#define UART_PUT_BRGR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR)
> -#define UART_PUT_RTOR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR)
> -#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR)
> -#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME)
> -#define UART_GET_IP_VERSION(port) __raw_readl((port)->membase + ATMEL_US_VERSION)
> +#define UART_PUT_CR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_CR)
> +#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR)
> +#define UART_PUT_MR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_MR)
> +#define UART_PUT_IER(port, v) __raw_writel(v, (port)->membase + ATMEL_US_IER)
> +#define UART_PUT_IDR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_IDR)
> +#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR)
> +#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR)
> +#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR)
> +#define UART_PUT_CHAR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_THR)
> +#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR)
> +#define UART_PUT_BRGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR)
> +#define UART_PUT_RTOR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR)
> +#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR)
> +#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME)
> +#define UART_GET_IP_VERS(port) __raw_readl((port)->membase + ATMEL_US_VERSION)
>
> /* PDC registers */
> -#define UART_PUT_PTCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR)
> -#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR)
> +#define UART_PUT_PTCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR)
> +#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR)
>
> -#define UART_PUT_RPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR)
> -#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR)
> -#define UART_PUT_RCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR)
> -#define UART_PUT_RNPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR)
> -#define UART_PUT_RNCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR)
> +#define UART_PUT_RPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR)
> +#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR)
> +#define UART_PUT_RCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR)
> +#define UART_PUT_RNPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR)
> +#define UART_PUT_RNCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR)
>
> -#define UART_PUT_TPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR)
> -#define UART_PUT_TCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR)
> -#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR)
> +#define UART_PUT_TPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR)
> +#define UART_PUT_TCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR)
> +#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR)
>
> struct atmel_dma_buffer {
> unsigned char *buf;
> @@ -1684,7 +1684,7 @@ static void atmel_get_ip_name(struct uart_port *port)
> atmel_port->is_usart = false;
> } else {
> /* fallback for older SoCs: use version field */
> - version = UART_GET_IP_VERSION(port);
> + version = UART_GET_IP_VERS(port);
> switch (version) {
> case 0x302:
> case 0x10213:
> diff --git a/include/linux/atmel_serial.h b/include/linux/atmel_serial.h
> index 00beddf..c384c21 100644
> --- a/include/linux/atmel_serial.h
> +++ b/include/linux/atmel_serial.h
> @@ -16,115 +16,115 @@
> #ifndef ATMEL_SERIAL_H
> #define ATMEL_SERIAL_H
>
> -#define ATMEL_US_CR 0x00 /* Control Register */
> -#define ATMEL_US_RSTRX (1 << 2) /* Reset Receiver */
> -#define ATMEL_US_RSTTX (1 << 3) /* Reset Transmitter */
> -#define ATMEL_US_RXEN (1 << 4) /* Receiver Enable */
> -#define ATMEL_US_RXDIS (1 << 5) /* Receiver Disable */
> -#define ATMEL_US_TXEN (1 << 6) /* Transmitter Enable */
> -#define ATMEL_US_TXDIS (1 << 7) /* Transmitter Disable */
> -#define ATMEL_US_RSTSTA (1 << 8) /* Reset Status Bits */
> -#define ATMEL_US_STTBRK (1 << 9) /* Start Break */
> -#define ATMEL_US_STPBRK (1 << 10) /* Stop Break */
> -#define ATMEL_US_STTTO (1 << 11) /* Start Time-out */
> -#define ATMEL_US_SENDA (1 << 12) /* Send Address */
> -#define ATMEL_US_RSTIT (1 << 13) /* Reset Iterations */
> -#define ATMEL_US_RSTNACK (1 << 14) /* Reset Non Acknowledge */
> -#define ATMEL_US_RETTO (1 << 15) /* Rearm Time-out */
> -#define ATMEL_US_DTREN (1 << 16) /* Data Terminal Ready Enable [AT91RM9200 only] */
> -#define ATMEL_US_DTRDIS (1 << 17) /* Data Terminal Ready Disable [AT91RM9200 only] */
> -#define ATMEL_US_RTSEN (1 << 18) /* Request To Send Enable */
> -#define ATMEL_US_RTSDIS (1 << 19) /* Request To Send Disable */
> +#define ATMEL_US_CR 0x00 /* Control Register */
> +#define ATMEL_US_RSTRX BIT(2) /* Reset Receiver */
> +#define ATMEL_US_RSTTX BIT(3) /* Reset Transmitter */
> +#define ATMEL_US_RXEN BIT(4) /* Receiver Enable */
> +#define ATMEL_US_RXDIS BIT(5) /* Receiver Disable */
> +#define ATMEL_US_TXEN BIT(6) /* Transmitter Enable */
> +#define ATMEL_US_TXDIS BIT(7) /* Transmitter Disable */
> +#define ATMEL_US_RSTSTA BIT(8) /* Reset Status Bits */
> +#define ATMEL_US_STTBRK BIT(9) /* Start Break */
> +#define ATMEL_US_STPBRK BIT(10) /* Stop Break */
> +#define ATMEL_US_STTTO BIT(11) /* Start Time-out */
> +#define ATMEL_US_SENDA BIT(12) /* Send Address */
> +#define ATMEL_US_RSTIT BIT(13) /* Reset Iterations */
> +#define ATMEL_US_RSTNACK BIT(14) /* Reset Non Acknowledge */
> +#define ATMEL_US_RETTO BIT(15) /* Rearm Time-out */
> +#define ATMEL_US_DTREN BIT(16) /* Data Terminal Ready Enable */
> +#define ATMEL_US_DTRDIS BIT(17) /* Data Terminal Ready Disable */
> +#define ATMEL_US_RTSEN BIT(18) /* Request To Send Enable */
> +#define ATMEL_US_RTSDIS BIT(19) /* Request To Send Disable */
>
> -#define ATMEL_US_MR 0x04 /* Mode Register */
> -#define ATMEL_US_USMODE (0xf << 0) /* Mode of the USART */
> -#define ATMEL_US_USMODE_NORMAL 0
> -#define ATMEL_US_USMODE_RS485 1
> -#define ATMEL_US_USMODE_HWHS 2
> -#define ATMEL_US_USMODE_MODEM 3
> -#define ATMEL_US_USMODE_ISO7816_T0 4
> -#define ATMEL_US_USMODE_ISO7816_T1 6
> -#define ATMEL_US_USMODE_IRDA 8
> -#define ATMEL_US_USCLKS (3 << 4) /* Clock Selection */
> -#define ATMEL_US_USCLKS_MCK (0 << 4)
> -#define ATMEL_US_USCLKS_MCK_DIV8 (1 << 4)
> -#define ATMEL_US_USCLKS_SCK (3 << 4)
> -#define ATMEL_US_CHRL (3 << 6) /* Character Length */
> -#define ATMEL_US_CHRL_5 (0 << 6)
> -#define ATMEL_US_CHRL_6 (1 << 6)
> -#define ATMEL_US_CHRL_7 (2 << 6)
> -#define ATMEL_US_CHRL_8 (3 << 6)
> -#define ATMEL_US_SYNC (1 << 8) /* Synchronous Mode Select */
> -#define ATMEL_US_PAR (7 << 9) /* Parity Type */
> -#define ATMEL_US_PAR_EVEN (0 << 9)
> -#define ATMEL_US_PAR_ODD (1 << 9)
> -#define ATMEL_US_PAR_SPACE (2 << 9)
> -#define ATMEL_US_PAR_MARK (3 << 9)
> -#define ATMEL_US_PAR_NONE (4 << 9)
> -#define ATMEL_US_PAR_MULTI_DROP (6 << 9)
> -#define ATMEL_US_NBSTOP (3 << 12) /* Number of Stop Bits */
> -#define ATMEL_US_NBSTOP_1 (0 << 12)
> -#define ATMEL_US_NBSTOP_1_5 (1 << 12)
> -#define ATMEL_US_NBSTOP_2 (2 << 12)
> -#define ATMEL_US_CHMODE (3 << 14) /* Channel Mode */
> -#define ATMEL_US_CHMODE_NORMAL (0 << 14)
> -#define ATMEL_US_CHMODE_ECHO (1 << 14)
> -#define ATMEL_US_CHMODE_LOC_LOOP (2 << 14)
> -#define ATMEL_US_CHMODE_REM_LOOP (3 << 14)
> -#define ATMEL_US_MSBF (1 << 16) /* Bit Order */
> -#define ATMEL_US_MODE9 (1 << 17) /* 9-bit Character Length */
> -#define ATMEL_US_CLKO (1 << 18) /* Clock Output Select */
> -#define ATMEL_US_OVER (1 << 19) /* Oversampling Mode */
> -#define ATMEL_US_INACK (1 << 20) /* Inhibit Non Acknowledge */
> -#define ATMEL_US_DSNACK (1 << 21) /* Disable Successive NACK */
> -#define ATMEL_US_MAX_ITER (7 << 24) /* Max Iterations */
> -#define ATMEL_US_FILTER (1 << 28) /* Infrared Receive Line Filter */
> +#define ATMEL_US_MR 0x04 /* Mode Register */
> +#define ATMEL_US_USMODE GENMASK(3, 0) /* Mode of the USART */
> +#define ATMEL_US_USMODE_NORMAL 0
> +#define ATMEL_US_USMODE_RS485 1
> +#define ATMEL_US_USMODE_HWHS 2
> +#define ATMEL_US_USMODE_MODEM 3
> +#define ATMEL_US_USMODE_ISO7816_T0 4
> +#define ATMEL_US_USMODE_ISO7816_T1 6
> +#define ATMEL_US_USMODE_IRDA 8
> +#define ATMEL_US_USCLKS GENMASK(5, 4) /* Clock Selection */
> +#define ATMEL_US_USCLKS_MCK (0 << 4)
> +#define ATMEL_US_USCLKS_MCK_DIV8 (1 << 4)
> +#define ATMEL_US_USCLKS_SCK (3 << 4)
> +#define ATMEL_US_CHRL GENMASK(7, 6) /* Character Length */
> +#define ATMEL_US_CHRL_5 (0 << 6)
> +#define ATMEL_US_CHRL_6 (1 << 6)
> +#define ATMEL_US_CHRL_7 (2 << 6)
> +#define ATMEL_US_CHRL_8 (3 << 6)
> +#define ATMEL_US_SYNC BIT(8) /* Synchronous Mode Select */
> +#define ATMEL_US_PAR GENMASK(11, 9) /* Parity Type */
> +#define ATMEL_US_PAR_EVEN (0 << 9)
> +#define ATMEL_US_PAR_ODD (1 << 9)
> +#define ATMEL_US_PAR_SPACE (2 << 9)
> +#define ATMEL_US_PAR_MARK (3 << 9)
> +#define ATMEL_US_PAR_NONE (4 << 9)
> +#define ATMEL_US_PAR_MULTI_DROP (6 << 9)
> +#define ATMEL_US_NBSTOP GENMASK(13, 12) /* Number of Stop Bits */
> +#define ATMEL_US_NBSTOP_1 (0 << 12)
> +#define ATMEL_US_NBSTOP_1_5 (1 << 12)
> +#define ATMEL_US_NBSTOP_2 (2 << 12)
> +#define ATMEL_US_CHMODE GENMASK(15, 14) /* Channel Mode */
> +#define ATMEL_US_CHMODE_NORMAL (0 << 14)
> +#define ATMEL_US_CHMODE_ECHO (1 << 14)
> +#define ATMEL_US_CHMODE_LOC_LOOP (2 << 14)
> +#define ATMEL_US_CHMODE_REM_LOOP (3 << 14)
> +#define ATMEL_US_MSBF BIT(16) /* Bit Order */
> +#define ATMEL_US_MODE9 BIT(17) /* 9-bit Character Length */
> +#define ATMEL_US_CLKO BIT(18) /* Clock Output Select */
> +#define ATMEL_US_OVER BIT(19) /* Oversampling Mode */
> +#define ATMEL_US_INACK BIT(20) /* Inhibit Non Acknowledge */
> +#define ATMEL_US_DSNACK BIT(21) /* Disable Successive NACK */
> +#define ATMEL_US_MAX_ITER GENMASK(26, 24) /* Max Iterations */
> +#define ATMEL_US_FILTER BIT(28) /* Infrared Receive Line Filter */
>
> -#define ATMEL_US_IER 0x08 /* Interrupt Enable Register */
> -#define ATMEL_US_RXRDY (1 << 0) /* Receiver Ready */
> -#define ATMEL_US_TXRDY (1 << 1) /* Transmitter Ready */
> -#define ATMEL_US_RXBRK (1 << 2) /* Break Received / End of Break */
> -#define ATMEL_US_ENDRX (1 << 3) /* End of Receiver Transfer */
> -#define ATMEL_US_ENDTX (1 << 4) /* End of Transmitter Transfer */
> -#define ATMEL_US_OVRE (1 << 5) /* Overrun Error */
> -#define ATMEL_US_FRAME (1 << 6) /* Framing Error */
> -#define ATMEL_US_PARE (1 << 7) /* Parity Error */
> -#define ATMEL_US_TIMEOUT (1 << 8) /* Receiver Time-out */
> -#define ATMEL_US_TXEMPTY (1 << 9) /* Transmitter Empty */
> -#define ATMEL_US_ITERATION (1 << 10) /* Max number of Repetitions Reached */
> -#define ATMEL_US_TXBUFE (1 << 11) /* Transmission Buffer Empty */
> -#define ATMEL_US_RXBUFF (1 << 12) /* Reception Buffer Full */
> -#define ATMEL_US_NACK (1 << 13) /* Non Acknowledge */
> -#define ATMEL_US_RIIC (1 << 16) /* Ring Indicator Input Change [AT91RM9200 only] */
> -#define ATMEL_US_DSRIC (1 << 17) /* Data Set Ready Input Change [AT91RM9200 only] */
> -#define ATMEL_US_DCDIC (1 << 18) /* Data Carrier Detect Input Change [AT91RM9200 only] */
> -#define ATMEL_US_CTSIC (1 << 19) /* Clear to Send Input Change */
> -#define ATMEL_US_RI (1 << 20) /* RI */
> -#define ATMEL_US_DSR (1 << 21) /* DSR */
> -#define ATMEL_US_DCD (1 << 22) /* DCD */
> -#define ATMEL_US_CTS (1 << 23) /* CTS */
> +#define ATMEL_US_IER 0x08 /* Interrupt Enable Register */
> +#define ATMEL_US_RXRDY BIT(0) /* Receiver Ready */
> +#define ATMEL_US_TXRDY BIT(1) /* Transmitter Ready */
> +#define ATMEL_US_RXBRK BIT(2) /* Break Received / End of Break */
> +#define ATMEL_US_ENDRX BIT(3) /* End of Receiver Transfer */
> +#define ATMEL_US_ENDTX BIT(4) /* End of Transmitter Transfer */
> +#define ATMEL_US_OVRE BIT(5) /* Overrun Error */
> +#define ATMEL_US_FRAME BIT(6) /* Framing Error */
> +#define ATMEL_US_PARE BIT(7) /* Parity Error */
> +#define ATMEL_US_TIMEOUT BIT(8) /* Receiver Time-out */
> +#define ATMEL_US_TXEMPTY BIT(9) /* Transmitter Empty */
> +#define ATMEL_US_ITERATION BIT(10) /* Max number of Repetitions Reached */
> +#define ATMEL_US_TXBUFE BIT(11) /* Transmission Buffer Empty */
> +#define ATMEL_US_RXBUFF BIT(12) /* Reception Buffer Full */
> +#define ATMEL_US_NACK BIT(13) /* Non Acknowledge */
> +#define ATMEL_US_RIIC BIT(16) /* Ring Indicator Input Change */
> +#define ATMEL_US_DSRIC BIT(17) /* Data Set Ready Input Change */
> +#define ATMEL_US_DCDIC BIT(18) /* Data Carrier Detect Input Change */
> +#define ATMEL_US_CTSIC BIT(19) /* Clear to Send Input Change */
> +#define ATMEL_US_RI BIT(20) /* RI */
> +#define ATMEL_US_DSR BIT(21) /* DSR */
> +#define ATMEL_US_DCD BIT(22) /* DCD */
> +#define ATMEL_US_CTS BIT(23) /* CTS */
>
> -#define ATMEL_US_IDR 0x0c /* Interrupt Disable Register */
> -#define ATMEL_US_IMR 0x10 /* Interrupt Mask Register */
> -#define ATMEL_US_CSR 0x14 /* Channel Status Register */
> -#define ATMEL_US_RHR 0x18 /* Receiver Holding Register */
> -#define ATMEL_US_THR 0x1c /* Transmitter Holding Register */
> -#define ATMEL_US_SYNH (1 << 15) /* Transmit/Receive Sync [AT91SAM9261 only] */
> +#define ATMEL_US_IDR 0x0c /* Interrupt Disable Register */
> +#define ATMEL_US_IMR 0x10 /* Interrupt Mask Register */
> +#define ATMEL_US_CSR 0x14 /* Channel Status Register */
> +#define ATMEL_US_RHR 0x18 /* Receiver Holding Register */
> +#define ATMEL_US_THR 0x1c /* Transmitter Holding Register */
> +#define ATMEL_US_SYNH BIT(15) /* Transmit/Receive Sync */
>
> -#define ATMEL_US_BRGR 0x20 /* Baud Rate Generator Register */
> -#define ATMEL_US_CD (0xffff << 0) /* Clock Divider */
> +#define ATMEL_US_BRGR 0x20 /* Baud Rate Generator Register */
> +#define ATMEL_US_CD GENMASK(15, 0) /* Clock Divider */
>
> -#define ATMEL_US_RTOR 0x24 /* Receiver Time-out Register */
> -#define ATMEL_US_TO (0xffff << 0) /* Time-out Value */
> +#define ATMEL_US_RTOR 0x24 /* Receiver Time-out Register */
> +#define ATMEL_US_TO GENMASK(15, 0) /* Time-out Value */
>
> -#define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */
> -#define ATMEL_US_TG (0xff << 0) /* Timeguard Value */
> +#define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */
> +#define ATMEL_US_TG GENMASK(7, 0) /* Timeguard Value */
>
> -#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */
> -#define ATMEL_US_NER 0x44 /* Number of Errors Register */
> -#define ATMEL_US_IF 0x4c /* IrDA Filter Register */
> +#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */
> +#define ATMEL_US_NER 0x44 /* Number of Errors Register */
> +#define ATMEL_US_IF 0x4c /* IrDA Filter Register */
>
> -#define ATMEL_US_NAME 0xf0 /* Ip Name */
> -#define ATMEL_US_VERSION 0xfc /* Ip Version */
> +#define ATMEL_US_NAME 0xf0 /* Ip Name */
> +#define ATMEL_US_VERSION 0xfc /* Ip Version */
>
> #endif
>
--
Nicolas Ferre
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
