+ Samsung SoC mailing list. On 2015년 06월 12일 21:59, Hyungwon Hwang wrote: > This patch renames pll_clk to sclk_clk. The clock referenced by pll_clk > is actually not the pll input clock for dsi. The pll input clock comes > from the board's oscillator directly. But for the backward > compatibility, the old clock name "pll_clk" is also OK. > > Signed-off-by: Hyungwon Hwang <human.hwang@xxxxxxxxxxx> > --- > Changes before: > - Refer https://patchwork.kernel.org/patch/6191721 > Changes for v6: > - Merged 2 patches > drm/exynos: dsi: add the backward compatibility for the renamed clock > drm/exynos: dsi: rename pll_clk to sclk_clk > > .../devicetree/bindings/video/exynos_dsim.txt | 7 +++-- > drivers/gpu/drm/exynos/exynos_drm_dsi.c | 36 ++++++++++------------ > 2 files changed, 20 insertions(+), 23 deletions(-) > > diff --git a/Documentation/devicetree/bindings/video/exynos_dsim.txt b/Documentation/devicetree/bindings/video/exynos_dsim.txt > index 802aa7e..44659dd 100644 > --- a/Documentation/devicetree/bindings/video/exynos_dsim.txt > +++ b/Documentation/devicetree/bindings/video/exynos_dsim.txt > @@ -10,13 +10,14 @@ Required properties: > - interrupts: should contain DSI interrupt > - clocks: list of clock specifiers, must contain an entry for each required > entry in clock-names > - - clock-names: should include "bus_clk"and "pll_clk" entries > + - clock-names: should include "bus_clk"and "sclk_mipi" entries > + the use of "pll_clk" is deprecated > - phys: list of phy specifiers, must contain an entry for each required > entry in phy-names > - phy-names: should include "dsim" entry > - vddcore-supply: MIPI DSIM Core voltage supply (e.g. 1.1V) > - vddio-supply: MIPI DSIM I/O and PLL voltage supply (e.g. 1.8V) > - - samsung,pll-clock-frequency: specifies frequency of the "pll_clk" clock > + - samsung,pll-clock-frequency: specifies frequency of the oscillator clock > - #address-cells, #size-cells: should be set respectively to <1> and <0> > according to DSI host bindings (see MIPI DSI bindings [1]) > > @@ -48,7 +49,7 @@ Example: > reg = <0x11C80000 0x10000>; > interrupts = <0 79 0>; > clocks = <&clock 286>, <&clock 143>; > - clock-names = "bus_clk", "pll_clk"; > + clock-names = "bus_clk", "sclk_mipi"; > phys = <&mipi_phy 1>; > phy-names = "dsim"; > vddcore-supply = <&vusb_reg>; > diff --git a/drivers/gpu/drm/exynos/exynos_drm_dsi.c b/drivers/gpu/drm/exynos/exynos_drm_dsi.c > index c1999ad..a3bfac2 100644 > --- a/drivers/gpu/drm/exynos/exynos_drm_dsi.c > +++ b/drivers/gpu/drm/exynos/exynos_drm_dsi.c > @@ -235,6 +235,8 @@ > #define DSI_XFER_TIMEOUT_MS 100 > #define DSI_RX_FIFO_EMPTY 0x30800002 > > +#define OLD_SCLK_MIPI_CLK_NAME "pll_clk" > + > enum exynos_dsi_transfer_type { > EXYNOS_DSI_TX, > EXYNOS_DSI_RX, > @@ -279,7 +281,7 @@ struct exynos_dsi { > > void __iomem *reg_base; > struct phy *phy; > - struct clk *pll_clk; > + struct clk *sclk_clk; > struct clk *bus_clk; > struct regulator_bulk_data supplies[2]; > int irq; > @@ -433,16 +435,7 @@ static unsigned long exynos_dsi_set_pll(struct exynos_dsi *dsi, > u16 m; > u32 reg; > > - clk_set_rate(dsi->pll_clk, dsi->pll_clk_rate); > - > - fin = clk_get_rate(dsi->pll_clk); > - if (!fin) { > - dev_err(dsi->dev, "failed to get PLL clock frequency\n"); > - return 0; > - } > - > - dev_dbg(dsi->dev, "PLL input frequency: %lu\n", fin); > - > + fin = dsi->pll_clk_rate; > fout = exynos_dsi_pll_find_pms(dsi, fin, freq, &p, &m, &s); > if (!fout) { > dev_err(dsi->dev, > @@ -1313,10 +1306,10 @@ static int exynos_dsi_poweron(struct exynos_dsi *dsi) > goto err_bus_clk; > } > > - ret = clk_prepare_enable(dsi->pll_clk); > + ret = clk_prepare_enable(dsi->sclk_clk); > if (ret < 0) { > dev_err(dsi->dev, "cannot enable pll clock %d\n", ret); > - goto err_pll_clk; > + goto err_sclk_clk; > } > > ret = phy_power_on(dsi->phy); > @@ -1328,8 +1321,8 @@ static int exynos_dsi_poweron(struct exynos_dsi *dsi) > return 0; > > err_phy: > - clk_disable_unprepare(dsi->pll_clk); > -err_pll_clk: > + clk_disable_unprepare(dsi->sclk_clk); > +err_sclk_clk: > clk_disable_unprepare(dsi->bus_clk); > err_bus_clk: > regulator_bulk_disable(ARRAY_SIZE(dsi->supplies), dsi->supplies); > @@ -1355,7 +1348,7 @@ static void exynos_dsi_poweroff(struct exynos_dsi *dsi) > > phy_power_off(dsi->phy); > > - clk_disable_unprepare(dsi->pll_clk); > + clk_disable_unprepare(dsi->sclk_clk); > clk_disable_unprepare(dsi->bus_clk); > > ret = regulator_bulk_disable(ARRAY_SIZE(dsi->supplies), dsi->supplies); > @@ -1722,10 +1715,13 @@ static int exynos_dsi_probe(struct platform_device *pdev) > return -EPROBE_DEFER; > } > > - dsi->pll_clk = devm_clk_get(dev, "pll_clk"); > - if (IS_ERR(dsi->pll_clk)) { > - dev_info(dev, "failed to get dsi pll input clock\n"); > - return PTR_ERR(dsi->pll_clk); > + dsi->sclk_clk = devm_clk_get(dev, "sclk_mipi"); > + if (IS_ERR(dsi->sclk_clk)) { > + dsi->sclk_clk = devm_clk_get(dev, OLD_SCLK_MIPI_CLK_NAME); > + if (IS_ERR(dsi->sclk_clk)) { > + dev_info(dev, "failed to get dsi sclk clock\n"); > + eturn PTR_ERR(dsi->sclk_clk); > + } > } > > dsi->bus_clk = devm_clk_get(dev, "bus_clk"); > -- > 1.9.1 > > -- > To unsubscribe from this list: send the line "unsubscribe devicetree" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html > -- To unsubscribe from this list: send the line "unsubscribe devicetree" in
