From: Frank Li <Frank.Li@xxxxxxxxxxxxx> This part just add necessary change to boot imx6ul. Update clock and pinctrl for imx6ul Signed-off-by: Frank Li <Frank.Li@xxxxxxxxxxxxx> Signed-off-by: Frank Li <Frank.Li@xxxxxxxxxxxxx> --- .../devicetree/bindings/clock/imx6ul-clock.txt | 13 ++++++++ .../bindings/pinctrl/fsl,imx6ul-pinctrl.txt | 36 ++++++++++++++++++++++ 2 files changed, 49 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/imx6ul-clock.txt create mode 100644 Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt diff --git a/Documentation/devicetree/bindings/clock/imx6ul-clock.txt b/Documentation/devicetree/bindings/clock/imx6ul-clock.txt new file mode 100644 index 0000000..3ff362e --- /dev/null +++ b/Documentation/devicetree/bindings/clock/imx6ul-clock.txt @@ -0,0 +1,13 @@ +* Clock bindings for Freescale i.MX6 UltraLite + +Required properties: +- compatible: Should be "fsl,imx6ul-ccm" +- reg: Address and length of the register set +- #clock-cells: Should be <1> +- clocks: list of clock specifiers, must contain an entry for each required + entry in clock-names +- clock-names: should include entries "ckil", "osc", "ipp_di0" and "ipp_di1" + +The clock consumer should specify the desired clock by having the clock +ID in its "clocks" phandle cell. See include/dt-bindings/clock/imx6ul-clock.h +for the full list of i.MX6 UltraLite clock IDs. diff --git a/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt new file mode 100644 index 0000000..a81bbf3 --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/fsl,imx6ul-pinctrl.txt @@ -0,0 +1,36 @@ +* Freescale i.MX6 UltraLite IOMUX Controller + +Please refer to fsl,imx-pinctrl.txt in this directory for common binding part +and usage. + +Required properties: +- compatible: "fsl,imx6ul-iomuxc" +- fsl,pins: each entry consists of 6 integers and represents the mux and config + setting for one pin. The first 5 integers <mux_reg conf_reg input_reg mux_val + input_val> are specified using a PIN_FUNC_ID macro, which can be found in + imx6ul-pinfunc.h under device tree source folder. The last integer CONFIG is + the pad setting value like pull-up on this pin. Please refer to i.MX6 UltraLite + Reference Manual for detailed CONFIG settings. + +CONFIG bits definition: +PAD_CTL_HYS (1 << 16) +PAD_CTL_PUS_100K_DOWN (0 << 14) +PAD_CTL_PUS_47K_UP (1 << 14) +PAD_CTL_PUS_100K_UP (2 << 14) +PAD_CTL_PUS_22K_UP (3 << 14) +PAD_CTL_PUE (1 << 13) +PAD_CTL_PKE (1 << 12) +PAD_CTL_ODE (1 << 11) +PAD_CTL_SPEED_LOW (0 << 6) +PAD_CTL_SPEED_MED (1 << 6) +PAD_CTL_SPEED_HIGH (3 << 6) +PAD_CTL_DSE_DISABLE (0 << 3) +PAD_CTL_DSE_260ohm (1 << 3) +PAD_CTL_DSE_130ohm (2 << 3) +PAD_CTL_DSE_87ohm (3 << 3) +PAD_CTL_DSE_65ohm (4 << 3) +PAD_CTL_DSE_52ohm (5 << 3) +PAD_CTL_DSE_43ohm (6 << 3) +PAD_CTL_DSE_37ohm (7 << 3) +PAD_CTL_SRE_FAST (1 << 0) +PAD_CTL_SRE_SLOW (0 << 0) -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in
