On 06/17/2015 05:10 PM, Rob Herring wrote:
On Fri, Jun 12, 2015 at 2:54 PM, Pantelis Antoniou
<pantelis.antoniou@xxxxxxxxxxxx> wrote:
Some applications require applying the same overlay to a different
target according to some external condition (for instance depending
on the slot a card has been inserted, the overlay target is different).
The indirect target use requires using the new
of_overlay_create_indirect() API which uses a text selector.
The format requires the use of a target-indirect node as follows:
fragment@0 {
target-indirect {
foo { target = <&foo_target>; };
bar { target = <&bar_target>; };
};
};
The problem with this is it does not scale. The overlay has to be
changed for every new target. If you had an add-on board (possibly
Not really. For our use case, at least, each target is a slot in the
chassis, so we end up with something like
target-indirect {
slot0 { target = <&sib0i2c>; };
slot1 { target = <&sib1i2c>; };
slot2 { target = <&sib2i2c>; };
slot3 { target = <&sib3i2c>; };
slot4 { target = <&sib4i2c>; };
slot5 { target = <&sib5i2c>; };
slot6 { target = <&sib6i2c>; };
slot7 { target = <&sib7i2c>; };
slot8 { target = <&sib8i2c>; };
};
where sib[0-8]i2c is defined in the master dts file.
Since the number of slots is well defined, the overlay will
always work. Sure, it may have to be updated if it is used in
a chassis with 20 slots, but that doesn't happen that often.
providing an overlay from an EEPROM), you would not want to have to
rebuild overlays with every new host board. It also only handles
translations of where to apply the overlay, but doesn't provide
translations of phandles within the overlay. Say a node that is a
clock or regulator consumer for example. Or am I missing something.
Grant and I discussed this briefly. I think we need a connector
definition in the base dtb which can provide the target for an
overlay. The connector should provide the translation between
connector local signals/buses and host signals/buses. We need to
define what this translation would look like for each binding.
At least for GPIO, we could have something similar to interrupt-map
properties. For example, to map connector gpio 0 to host gpio 66 and
connector gpio 1 to host gpio 44:
gpio-map = <0 &host-gpio 66>, <1 &host-gpio 44>;
We'd need to define how to handle I2C, SPI, regulators, and clocks
minimally. Perhaps rather than trying to apply nodes into the base
dtb, they should be under the connector and the kernel has to learn to
not just look for child nodes for various bindings. Just thinking
aloud...
Anything is fine with me, as long as it is usable (and does not require
us to create 9 overlay files for sib[0-8] from the example above).
The real tricky part is pci, where it is not just about simple target
redirection but irq numbers, memory address ranges, and bus number ranges.
It would be quite useful to have a workable solution for that as well,
but at least I don't have an idea how it could be done.
Talking about connector ...
Right now we have something like
sib0 {
compatible = "jnx,sib-connector", "simple-bus";
... (various properties)
};
Maybe we could use something like the following ?
sib0 {
compatible = "jnx,sib-connector", "simple-bus";
... (various attributes)
ref0 = <&sib0i2c>;
ref1 = <&sib0spi>;
};
and then just reference ref0 and ref1 as targets in the overlay itself ?
Guenter
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
