Add the link for atmel-isi and ov2640 sensor node.
Signed-off-by: Josh Wu <josh.wu@xxxxxxxxx>
---
arch/arm/boot/dts/at91sam9g45.dtsi | 4 +++
arch/arm/boot/dts/at91sam9m10g45ek.dts | 45 ++++++++++++++++++++++++++++++++++
2 files changed, 49 insertions(+)
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index d260ba7..e707613 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -1070,6 +1070,10 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_isi>;
status = "disabled";
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
};
pwm0: pwm@fffb8000 {
diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts
index 1375d33..5062e18 100644
--- a/arch/arm/boot/dts/at91sam9m10g45ek.dts
+++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts
@@ -63,6 +63,25 @@
i2c0: i2c@fff84000 {
status = "okay";
+ ov2640: camera@30 {
+ compatible = "ovti,ov2640";
+ reg = <0x30>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pck1_as_isi_mck &pinctrl_sensor_power &pinctrl_sensor_reset>;
+ resetb-gpios = <&pioD 12 GPIO_ACTIVE_LOW>;
+ pwdn-gpios = <&pioD 13 GPIO_ACTIVE_HIGH>;
+ clocks = <&pck1>;
+ clock-names = "xvclk";
+ assigned-clocks = <&pck1>;
+ assigned-clock-rates = <25000000>;
+
+ port {
+ ov2640_0: endpoint {
+ remote-endpoint = <&isi_0>;
+ bus-width = <8>;
+ };
+ };
+ };
};
i2c1: i2c@fff88000 {
@@ -101,6 +120,22 @@
};
pinctrl@fffff200 {
+ camera_sensor {
+ pinctrl_pck1_as_isi_mck: pck1_as_isi_mck-0 {
+ atmel,pins =
+ <AT91_PIOB 31 AT91_PERIPH_B AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_sensor_reset: sensor_reset-0 {
+ atmel,pins =
+ <AT91_PIOD 12 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+
+ pinctrl_sensor_power: sensor_power-0 {
+ atmel,pins =
+ <AT91_PIOD 13 AT91_PERIPH_GPIO AT91_PINCTRL_NONE>;
+ };
+ };
mmc0 {
pinctrl_board_mmc0: mmc0-board {
atmel,pins =
@@ -155,6 +190,16 @@
status = "okay";
};
+ isi@fffb4000 {
+ status = "okay";
+ port {
+ isi_0: endpoint {
+ remote-endpoint = <&ov2640_0>;
+ bus-width = <8>;
+ };
+ };
+ };
+
pwm0: pwm@fffb8000 {
status = "okay";
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
