Some regulators need to be configured to pull down a resistor
when the regulator is disabled. Add an op (set_pull_down) and a
DT property + constraint to support this.
Cc: <devicetree@xxxxxxxxxxxxxxx>
Signed-off-by: Stephen Boyd <sboyd@xxxxxxxxxxxxxx>
---
Documentation/devicetree/bindings/regulator/regulator.txt | 1 +
drivers/regulator/core.c | 8 ++++++++
drivers/regulator/of_regulator.c | 2 ++
include/linux/regulator/driver.h | 5 +++++
include/linux/regulator/machine.h | 2 ++
5 files changed, 18 insertions(+)
diff --git a/Documentation/devicetree/bindings/regulator/regulator.txt b/Documentation/devicetree/bindings/regulator/regulator.txt
index 553d2d0fe6d9..6c79fd70ab5a 100644
--- a/Documentation/devicetree/bindings/regulator/regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/regulator.txt
@@ -39,6 +39,7 @@ Optional properties:
documentation explains which values the regulator supports.
- regulator-system-load: Load in uA present on regulator that is not captured by
any consumer request.
+- regulator-pull-down: Enable pull down resistor when the regulator is disabled.
Deprecated properties:
- regulator-compatible: If a regulator chip contains multiple
diff --git a/drivers/regulator/core.c b/drivers/regulator/core.c
index ab383dfe5386..1d6172a9f65c 100644
--- a/drivers/regulator/core.c
+++ b/drivers/regulator/core.c
@@ -1051,6 +1051,14 @@ static int set_machine_constraints(struct regulator_dev *rdev,
}
}
+ if (rdev->constraints->pull_down && ops->set_pull_down) {
+ ret = ops->set_pull_down(rdev);
+ if (ret < 0) {
+ rdev_err(rdev, "failed to set pull down\n");
+ goto out;
+ }
+ }
+
print_constraints(rdev);
return 0;
out:
diff --git a/drivers/regulator/of_regulator.c b/drivers/regulator/of_regulator.c
index b44da860ac22..237b014666fa 100644
--- a/drivers/regulator/of_regulator.c
+++ b/drivers/regulator/of_regulator.c
@@ -67,6 +67,8 @@ static void of_get_regulation_constraints(struct device_node *np,
if (!constraints->always_on) /* status change should be possible. */
constraints->valid_ops_mask |= REGULATOR_CHANGE_STATUS;
+ constraints->pull_down = of_property_read_bool(np, "regulator-pull-down");
+
if (of_property_read_bool(np, "regulator-allow-bypass"))
constraints->valid_ops_mask |= REGULATOR_CHANGE_BYPASS;
diff --git a/include/linux/regulator/driver.h b/include/linux/regulator/driver.h
index fffa688ac3a7..5eb85e152eb7 100644
--- a/include/linux/regulator/driver.h
+++ b/include/linux/regulator/driver.h
@@ -121,6 +121,9 @@ struct regulator_linear_range {
* @set_suspend_mode: Set the operating mode for the regulator when the
* system is suspended.
*
+ * @set_pull_down: Configure the regulator to pull down when the regulator
+ * is disabled.
+ *
* This struct describes regulator operations which can be implemented by
* regulator chip drivers.
*/
@@ -187,6 +190,8 @@ struct regulator_ops {
/* set regulator suspend operating mode (defined in consumer.h) */
int (*set_suspend_mode) (struct regulator_dev *, unsigned int mode);
+
+ int (*set_pull_down) (struct regulator_dev *);
};
/*
diff --git a/include/linux/regulator/machine.h b/include/linux/regulator/machine.h
index 01526559c8c3..8ffb0619a03c 100644
--- a/include/linux/regulator/machine.h
+++ b/include/linux/regulator/machine.h
@@ -87,6 +87,7 @@ struct regulator_state {
* applied.
* @apply_uV: Apply the voltage constraint when initialising.
* @ramp_disable: Disable ramp delay when initialising or when setting voltage.
+ * @pull_down: Enable pull down when regulator is disabled.
*
* @input_uV: Input voltage for regulator when supplied by another regulator.
*
@@ -141,6 +142,7 @@ struct regulation_constraints {
unsigned boot_on:1; /* bootloader/firmware enabled regulator */
unsigned apply_uV:1; /* apply uV constraint if min == max */
unsigned ramp_disable:1; /* disable ramp delay */
+ unsigned pull_down:1; /* pull down resistor when regulator off */
};
/**
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
