> -----Original Message----- > From: Bastien Nocera [mailto:hadess@xxxxxxxxxx] > Sent: 04 June, 2015 15:58 > To: Tirdea, Irina > Cc: Mark Rutland; Dmitry Torokhov; linux-input@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx > Subject: Re: [PATCH 8/9] input: goodix: add support for ESD > > On Thu, 2015-05-28 at 14:26 +0000, Tirdea, Irina wrote: > > > > > -----Original Message----- > > > From: linux-input-owner@xxxxxxxxxxxxxxx [mailto: > > > linux-input-owner@xxxxxxxxxxxxxxx] On Behalf Of Mark Rutland > > > Sent: 28 May, 2015 16:24 > > > To: Tirdea, Irina > > > Cc: Dmitry Torokhov; Bastien Nocera; linux-input@xxxxxxxxxxxxxxx; > > > devicetree@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx > > > Subject: Re: [PATCH 8/9] input: goodix: add support for ESD > > > > > > On Thu, May 28, 2015 at 01:47:44PM +0100, Irina Tirdea wrote: > > > > Add ESD (Electrostatic Discharge) protection mechanism. > > > > > > > > The driver enables ESD protection in HW and checks a register > > > > to determine if ESD occurred. If ESD is signalled by the HW, > > > > the driver will reset the device. > > > > > > > > The ESD poll time (in ms) can be set through > > > > esd-recovery-timeout-ms ACPI/DT property. If it is set to 0, > > > > ESD protection is disabled. > > > > > > > > Signed-off-by: Irina Tirdea <irina.tirdea@xxxxxxxxx> > > > > --- > > > > .../bindings/input/touchscreen/goodix.txt | 4 + > > > > drivers/input/touchscreen/goodix.c | 106 > > > > ++++++++++++++++++++- > > > > 2 files changed, 106 insertions(+), 4 deletions(-) > > > > > > > > diff --git > > > > a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt > > > b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt > > > > index 9e4ff69..9132ee0 100644 > > > > --- > > > > a/Documentation/devicetree/bindings/input/touchscreen/goodix.txt > > > > +++ > > > > b/Documentation/devicetree/bindings/input/touchscreen/goodix.txt > > > > @@ -19,6 +19,10 @@ Optional properties: > > > > > > > > - device-config : device configuration information > > > > (specified as byte > > > > array). Maximum size is 240 bytes. > > > > + - esd-recovery-timeout-ms : ESD poll time (in milli seconds) > > > > for the driver to > > > > + check if ESD occurred and in that > > > > case reset the > > > > + device. ESD is disabled if this > > > > property is not set > > > > + or is set to 0. > > > > > > This sounds like software configuration rather than HW description. > > > Is > > > there any reason this needs to be a DT property? > > > > > > > Although this enables a software feature, it depends on the platform > > if electrostatic discharge > > protection should be enabled or not. Some platform designs handle ESD > > better and do not need > > the SW mechanism, so the property can be used to disable it. > > > > I also saw an example in > > Documentation/devicetree/bindings/input/touchscreen/tsc2005.txt > > and I though this is the standard way to use it. > > As for the configuration data, is this useful/used on ACPI? This can be used with ACPI 5.1 by specifying the timeout as a _DSD property. I will add an excerpt from an ACPI DSDT file in the commit message. > > > > Can we not just choose a sensible default and allow this to be > > > overridden dynamically? > > > > I could separate the enabling part from the actual poll timeout by > > using a DT property to enable/disable > > ESD and a sysfs property to set the timeout. I can also move this > > over to sysfs entirely if you prefer. > > If this needs to be in the DT for some devices, and isn't available > from ACPI, maybe we should have a list of DMI matches for ACPI instead, > with a module option to override it? ��.n��������+%������w��{.n����z�{��ܨ}���Ơz�j:+v�����w����ޙ��&�)ߡ�a����z�ޗ���ݢj��w�f
