This patch updates macro definitions in atmel_serial.h to fit the 80 column rule. Please note that some deprecated comments such as "[AT91SAM9261 only]" are removed as the corresponding bits also exist in some later chips. The patch also fix macro definitions in atmel_serial.c to replace (port,v) by (port, v). Signed-off-by: Cyrille Pitchen <cyrille.pitchen@xxxxxxxxx> --- drivers/tty/serial/atmel_serial.c | 52 +++++----- include/linux/atmel_serial.h | 204 +++++++++++++++++++------------------- 2 files changed, 128 insertions(+), 128 deletions(-) diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c index 2a8f528..112e74b 100644 --- a/drivers/tty/serial/atmel_serial.c +++ b/drivers/tty/serial/atmel_serial.c @@ -89,35 +89,35 @@ static void atmel_stop_rx(struct uart_port *port); #define ATMEL_ISR_PASS_LIMIT 256 /* UART registers. CR is write-only, hence no GET macro */ -#define UART_PUT_CR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_CR) -#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR) -#define UART_PUT_MR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_MR) -#define UART_PUT_IER(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IER) -#define UART_PUT_IDR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_IDR) -#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR) -#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR) -#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR) -#define UART_PUT_CHAR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_THR) -#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR) -#define UART_PUT_BRGR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR) -#define UART_PUT_RTOR(port,v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR) -#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR) -#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME) -#define UART_GET_IP_VERSION(port) __raw_readl((port)->membase + ATMEL_US_VERSION) +#define UART_PUT_CR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_CR) +#define UART_GET_MR(port) __raw_readl((port)->membase + ATMEL_US_MR) +#define UART_PUT_MR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_MR) +#define UART_PUT_IER(port, v) __raw_writel(v, (port)->membase + ATMEL_US_IER) +#define UART_PUT_IDR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_IDR) +#define UART_GET_IMR(port) __raw_readl((port)->membase + ATMEL_US_IMR) +#define UART_GET_CSR(port) __raw_readl((port)->membase + ATMEL_US_CSR) +#define UART_GET_CHAR(port) __raw_readl((port)->membase + ATMEL_US_RHR) +#define UART_PUT_CHAR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_THR) +#define UART_GET_BRGR(port) __raw_readl((port)->membase + ATMEL_US_BRGR) +#define UART_PUT_BRGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_BRGR) +#define UART_PUT_RTOR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_RTOR) +#define UART_PUT_TTGR(port, v) __raw_writel(v, (port)->membase + ATMEL_US_TTGR) +#define UART_GET_IP_NAME(port) __raw_readl((port)->membase + ATMEL_US_NAME) +#define UART_GET_IP_VERS(port) __raw_readl((port)->membase + ATMEL_US_VERSION) /* PDC registers */ -#define UART_PUT_PTCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR) -#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR) +#define UART_PUT_PTCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_PTCR) +#define UART_GET_PTSR(port) __raw_readl((port)->membase + ATMEL_PDC_PTSR) -#define UART_PUT_RPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR) -#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR) -#define UART_PUT_RCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR) -#define UART_PUT_RNPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR) -#define UART_PUT_RNCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR) +#define UART_PUT_RPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RPR) +#define UART_GET_RPR(port) __raw_readl((port)->membase + ATMEL_PDC_RPR) +#define UART_PUT_RCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RCR) +#define UART_PUT_RNPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNPR) +#define UART_PUT_RNCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_RNCR) -#define UART_PUT_TPR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR) -#define UART_PUT_TCR(port,v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR) -#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR) +#define UART_PUT_TPR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_TPR) +#define UART_PUT_TCR(port, v) __raw_writel(v, (port)->membase + ATMEL_PDC_TCR) +#define UART_GET_TCR(port) __raw_readl((port)->membase + ATMEL_PDC_TCR) struct atmel_dma_buffer { unsigned char *buf; @@ -1684,7 +1684,7 @@ static void atmel_get_ip_name(struct uart_port *port) atmel_port->is_usart = false; } else { /* fallback for older SoCs: use version field */ - version = UART_GET_IP_VERSION(port); + version = UART_GET_IP_VERS(port); switch (version) { case 0x302: case 0x10213: diff --git a/include/linux/atmel_serial.h b/include/linux/atmel_serial.h index 00beddf..c384c21 100644 --- a/include/linux/atmel_serial.h +++ b/include/linux/atmel_serial.h @@ -16,115 +16,115 @@ #ifndef ATMEL_SERIAL_H #define ATMEL_SERIAL_H -#define ATMEL_US_CR 0x00 /* Control Register */ -#define ATMEL_US_RSTRX (1 << 2) /* Reset Receiver */ -#define ATMEL_US_RSTTX (1 << 3) /* Reset Transmitter */ -#define ATMEL_US_RXEN (1 << 4) /* Receiver Enable */ -#define ATMEL_US_RXDIS (1 << 5) /* Receiver Disable */ -#define ATMEL_US_TXEN (1 << 6) /* Transmitter Enable */ -#define ATMEL_US_TXDIS (1 << 7) /* Transmitter Disable */ -#define ATMEL_US_RSTSTA (1 << 8) /* Reset Status Bits */ -#define ATMEL_US_STTBRK (1 << 9) /* Start Break */ -#define ATMEL_US_STPBRK (1 << 10) /* Stop Break */ -#define ATMEL_US_STTTO (1 << 11) /* Start Time-out */ -#define ATMEL_US_SENDA (1 << 12) /* Send Address */ -#define ATMEL_US_RSTIT (1 << 13) /* Reset Iterations */ -#define ATMEL_US_RSTNACK (1 << 14) /* Reset Non Acknowledge */ -#define ATMEL_US_RETTO (1 << 15) /* Rearm Time-out */ -#define ATMEL_US_DTREN (1 << 16) /* Data Terminal Ready Enable [AT91RM9200 only] */ -#define ATMEL_US_DTRDIS (1 << 17) /* Data Terminal Ready Disable [AT91RM9200 only] */ -#define ATMEL_US_RTSEN (1 << 18) /* Request To Send Enable */ -#define ATMEL_US_RTSDIS (1 << 19) /* Request To Send Disable */ +#define ATMEL_US_CR 0x00 /* Control Register */ +#define ATMEL_US_RSTRX BIT(2) /* Reset Receiver */ +#define ATMEL_US_RSTTX BIT(3) /* Reset Transmitter */ +#define ATMEL_US_RXEN BIT(4) /* Receiver Enable */ +#define ATMEL_US_RXDIS BIT(5) /* Receiver Disable */ +#define ATMEL_US_TXEN BIT(6) /* Transmitter Enable */ +#define ATMEL_US_TXDIS BIT(7) /* Transmitter Disable */ +#define ATMEL_US_RSTSTA BIT(8) /* Reset Status Bits */ +#define ATMEL_US_STTBRK BIT(9) /* Start Break */ +#define ATMEL_US_STPBRK BIT(10) /* Stop Break */ +#define ATMEL_US_STTTO BIT(11) /* Start Time-out */ +#define ATMEL_US_SENDA BIT(12) /* Send Address */ +#define ATMEL_US_RSTIT BIT(13) /* Reset Iterations */ +#define ATMEL_US_RSTNACK BIT(14) /* Reset Non Acknowledge */ +#define ATMEL_US_RETTO BIT(15) /* Rearm Time-out */ +#define ATMEL_US_DTREN BIT(16) /* Data Terminal Ready Enable */ +#define ATMEL_US_DTRDIS BIT(17) /* Data Terminal Ready Disable */ +#define ATMEL_US_RTSEN BIT(18) /* Request To Send Enable */ +#define ATMEL_US_RTSDIS BIT(19) /* Request To Send Disable */ -#define ATMEL_US_MR 0x04 /* Mode Register */ -#define ATMEL_US_USMODE (0xf << 0) /* Mode of the USART */ -#define ATMEL_US_USMODE_NORMAL 0 -#define ATMEL_US_USMODE_RS485 1 -#define ATMEL_US_USMODE_HWHS 2 -#define ATMEL_US_USMODE_MODEM 3 -#define ATMEL_US_USMODE_ISO7816_T0 4 -#define ATMEL_US_USMODE_ISO7816_T1 6 -#define ATMEL_US_USMODE_IRDA 8 -#define ATMEL_US_USCLKS (3 << 4) /* Clock Selection */ -#define ATMEL_US_USCLKS_MCK (0 << 4) -#define ATMEL_US_USCLKS_MCK_DIV8 (1 << 4) -#define ATMEL_US_USCLKS_SCK (3 << 4) -#define ATMEL_US_CHRL (3 << 6) /* Character Length */ -#define ATMEL_US_CHRL_5 (0 << 6) -#define ATMEL_US_CHRL_6 (1 << 6) -#define ATMEL_US_CHRL_7 (2 << 6) -#define ATMEL_US_CHRL_8 (3 << 6) -#define ATMEL_US_SYNC (1 << 8) /* Synchronous Mode Select */ -#define ATMEL_US_PAR (7 << 9) /* Parity Type */ -#define ATMEL_US_PAR_EVEN (0 << 9) -#define ATMEL_US_PAR_ODD (1 << 9) -#define ATMEL_US_PAR_SPACE (2 << 9) -#define ATMEL_US_PAR_MARK (3 << 9) -#define ATMEL_US_PAR_NONE (4 << 9) -#define ATMEL_US_PAR_MULTI_DROP (6 << 9) -#define ATMEL_US_NBSTOP (3 << 12) /* Number of Stop Bits */ -#define ATMEL_US_NBSTOP_1 (0 << 12) -#define ATMEL_US_NBSTOP_1_5 (1 << 12) -#define ATMEL_US_NBSTOP_2 (2 << 12) -#define ATMEL_US_CHMODE (3 << 14) /* Channel Mode */ -#define ATMEL_US_CHMODE_NORMAL (0 << 14) -#define ATMEL_US_CHMODE_ECHO (1 << 14) -#define ATMEL_US_CHMODE_LOC_LOOP (2 << 14) -#define ATMEL_US_CHMODE_REM_LOOP (3 << 14) -#define ATMEL_US_MSBF (1 << 16) /* Bit Order */ -#define ATMEL_US_MODE9 (1 << 17) /* 9-bit Character Length */ -#define ATMEL_US_CLKO (1 << 18) /* Clock Output Select */ -#define ATMEL_US_OVER (1 << 19) /* Oversampling Mode */ -#define ATMEL_US_INACK (1 << 20) /* Inhibit Non Acknowledge */ -#define ATMEL_US_DSNACK (1 << 21) /* Disable Successive NACK */ -#define ATMEL_US_MAX_ITER (7 << 24) /* Max Iterations */ -#define ATMEL_US_FILTER (1 << 28) /* Infrared Receive Line Filter */ +#define ATMEL_US_MR 0x04 /* Mode Register */ +#define ATMEL_US_USMODE GENMASK(3, 0) /* Mode of the USART */ +#define ATMEL_US_USMODE_NORMAL 0 +#define ATMEL_US_USMODE_RS485 1 +#define ATMEL_US_USMODE_HWHS 2 +#define ATMEL_US_USMODE_MODEM 3 +#define ATMEL_US_USMODE_ISO7816_T0 4 +#define ATMEL_US_USMODE_ISO7816_T1 6 +#define ATMEL_US_USMODE_IRDA 8 +#define ATMEL_US_USCLKS GENMASK(5, 4) /* Clock Selection */ +#define ATMEL_US_USCLKS_MCK (0 << 4) +#define ATMEL_US_USCLKS_MCK_DIV8 (1 << 4) +#define ATMEL_US_USCLKS_SCK (3 << 4) +#define ATMEL_US_CHRL GENMASK(7, 6) /* Character Length */ +#define ATMEL_US_CHRL_5 (0 << 6) +#define ATMEL_US_CHRL_6 (1 << 6) +#define ATMEL_US_CHRL_7 (2 << 6) +#define ATMEL_US_CHRL_8 (3 << 6) +#define ATMEL_US_SYNC BIT(8) /* Synchronous Mode Select */ +#define ATMEL_US_PAR GENMASK(11, 9) /* Parity Type */ +#define ATMEL_US_PAR_EVEN (0 << 9) +#define ATMEL_US_PAR_ODD (1 << 9) +#define ATMEL_US_PAR_SPACE (2 << 9) +#define ATMEL_US_PAR_MARK (3 << 9) +#define ATMEL_US_PAR_NONE (4 << 9) +#define ATMEL_US_PAR_MULTI_DROP (6 << 9) +#define ATMEL_US_NBSTOP GENMASK(13, 12) /* Number of Stop Bits */ +#define ATMEL_US_NBSTOP_1 (0 << 12) +#define ATMEL_US_NBSTOP_1_5 (1 << 12) +#define ATMEL_US_NBSTOP_2 (2 << 12) +#define ATMEL_US_CHMODE GENMASK(15, 14) /* Channel Mode */ +#define ATMEL_US_CHMODE_NORMAL (0 << 14) +#define ATMEL_US_CHMODE_ECHO (1 << 14) +#define ATMEL_US_CHMODE_LOC_LOOP (2 << 14) +#define ATMEL_US_CHMODE_REM_LOOP (3 << 14) +#define ATMEL_US_MSBF BIT(16) /* Bit Order */ +#define ATMEL_US_MODE9 BIT(17) /* 9-bit Character Length */ +#define ATMEL_US_CLKO BIT(18) /* Clock Output Select */ +#define ATMEL_US_OVER BIT(19) /* Oversampling Mode */ +#define ATMEL_US_INACK BIT(20) /* Inhibit Non Acknowledge */ +#define ATMEL_US_DSNACK BIT(21) /* Disable Successive NACK */ +#define ATMEL_US_MAX_ITER GENMASK(26, 24) /* Max Iterations */ +#define ATMEL_US_FILTER BIT(28) /* Infrared Receive Line Filter */ -#define ATMEL_US_IER 0x08 /* Interrupt Enable Register */ -#define ATMEL_US_RXRDY (1 << 0) /* Receiver Ready */ -#define ATMEL_US_TXRDY (1 << 1) /* Transmitter Ready */ -#define ATMEL_US_RXBRK (1 << 2) /* Break Received / End of Break */ -#define ATMEL_US_ENDRX (1 << 3) /* End of Receiver Transfer */ -#define ATMEL_US_ENDTX (1 << 4) /* End of Transmitter Transfer */ -#define ATMEL_US_OVRE (1 << 5) /* Overrun Error */ -#define ATMEL_US_FRAME (1 << 6) /* Framing Error */ -#define ATMEL_US_PARE (1 << 7) /* Parity Error */ -#define ATMEL_US_TIMEOUT (1 << 8) /* Receiver Time-out */ -#define ATMEL_US_TXEMPTY (1 << 9) /* Transmitter Empty */ -#define ATMEL_US_ITERATION (1 << 10) /* Max number of Repetitions Reached */ -#define ATMEL_US_TXBUFE (1 << 11) /* Transmission Buffer Empty */ -#define ATMEL_US_RXBUFF (1 << 12) /* Reception Buffer Full */ -#define ATMEL_US_NACK (1 << 13) /* Non Acknowledge */ -#define ATMEL_US_RIIC (1 << 16) /* Ring Indicator Input Change [AT91RM9200 only] */ -#define ATMEL_US_DSRIC (1 << 17) /* Data Set Ready Input Change [AT91RM9200 only] */ -#define ATMEL_US_DCDIC (1 << 18) /* Data Carrier Detect Input Change [AT91RM9200 only] */ -#define ATMEL_US_CTSIC (1 << 19) /* Clear to Send Input Change */ -#define ATMEL_US_RI (1 << 20) /* RI */ -#define ATMEL_US_DSR (1 << 21) /* DSR */ -#define ATMEL_US_DCD (1 << 22) /* DCD */ -#define ATMEL_US_CTS (1 << 23) /* CTS */ +#define ATMEL_US_IER 0x08 /* Interrupt Enable Register */ +#define ATMEL_US_RXRDY BIT(0) /* Receiver Ready */ +#define ATMEL_US_TXRDY BIT(1) /* Transmitter Ready */ +#define ATMEL_US_RXBRK BIT(2) /* Break Received / End of Break */ +#define ATMEL_US_ENDRX BIT(3) /* End of Receiver Transfer */ +#define ATMEL_US_ENDTX BIT(4) /* End of Transmitter Transfer */ +#define ATMEL_US_OVRE BIT(5) /* Overrun Error */ +#define ATMEL_US_FRAME BIT(6) /* Framing Error */ +#define ATMEL_US_PARE BIT(7) /* Parity Error */ +#define ATMEL_US_TIMEOUT BIT(8) /* Receiver Time-out */ +#define ATMEL_US_TXEMPTY BIT(9) /* Transmitter Empty */ +#define ATMEL_US_ITERATION BIT(10) /* Max number of Repetitions Reached */ +#define ATMEL_US_TXBUFE BIT(11) /* Transmission Buffer Empty */ +#define ATMEL_US_RXBUFF BIT(12) /* Reception Buffer Full */ +#define ATMEL_US_NACK BIT(13) /* Non Acknowledge */ +#define ATMEL_US_RIIC BIT(16) /* Ring Indicator Input Change */ +#define ATMEL_US_DSRIC BIT(17) /* Data Set Ready Input Change */ +#define ATMEL_US_DCDIC BIT(18) /* Data Carrier Detect Input Change */ +#define ATMEL_US_CTSIC BIT(19) /* Clear to Send Input Change */ +#define ATMEL_US_RI BIT(20) /* RI */ +#define ATMEL_US_DSR BIT(21) /* DSR */ +#define ATMEL_US_DCD BIT(22) /* DCD */ +#define ATMEL_US_CTS BIT(23) /* CTS */ -#define ATMEL_US_IDR 0x0c /* Interrupt Disable Register */ -#define ATMEL_US_IMR 0x10 /* Interrupt Mask Register */ -#define ATMEL_US_CSR 0x14 /* Channel Status Register */ -#define ATMEL_US_RHR 0x18 /* Receiver Holding Register */ -#define ATMEL_US_THR 0x1c /* Transmitter Holding Register */ -#define ATMEL_US_SYNH (1 << 15) /* Transmit/Receive Sync [AT91SAM9261 only] */ +#define ATMEL_US_IDR 0x0c /* Interrupt Disable Register */ +#define ATMEL_US_IMR 0x10 /* Interrupt Mask Register */ +#define ATMEL_US_CSR 0x14 /* Channel Status Register */ +#define ATMEL_US_RHR 0x18 /* Receiver Holding Register */ +#define ATMEL_US_THR 0x1c /* Transmitter Holding Register */ +#define ATMEL_US_SYNH BIT(15) /* Transmit/Receive Sync */ -#define ATMEL_US_BRGR 0x20 /* Baud Rate Generator Register */ -#define ATMEL_US_CD (0xffff << 0) /* Clock Divider */ +#define ATMEL_US_BRGR 0x20 /* Baud Rate Generator Register */ +#define ATMEL_US_CD GENMASK(15, 0) /* Clock Divider */ -#define ATMEL_US_RTOR 0x24 /* Receiver Time-out Register */ -#define ATMEL_US_TO (0xffff << 0) /* Time-out Value */ +#define ATMEL_US_RTOR 0x24 /* Receiver Time-out Register */ +#define ATMEL_US_TO GENMASK(15, 0) /* Time-out Value */ -#define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */ -#define ATMEL_US_TG (0xff << 0) /* Timeguard Value */ +#define ATMEL_US_TTGR 0x28 /* Transmitter Timeguard Register */ +#define ATMEL_US_TG GENMASK(7, 0) /* Timeguard Value */ -#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */ -#define ATMEL_US_NER 0x44 /* Number of Errors Register */ -#define ATMEL_US_IF 0x4c /* IrDA Filter Register */ +#define ATMEL_US_FIDI 0x40 /* FI DI Ratio Register */ +#define ATMEL_US_NER 0x44 /* Number of Errors Register */ +#define ATMEL_US_IF 0x4c /* IrDA Filter Register */ -#define ATMEL_US_NAME 0xf0 /* Ip Name */ -#define ATMEL_US_VERSION 0xfc /* Ip Version */ +#define ATMEL_US_NAME 0xf0 /* Ip Name */ +#define ATMEL_US_VERSION 0xfc /* Ip Version */ #endif -- 1.8.2.2 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html