Main PLL controller has post divider bits in a separate register in pll controller. Use the value from this register instead of fixed divider when available. Signed-off-by: Murali Karicheri <m-karicheri2@xxxxxx> --- .../devicetree/bindings/clock/keystone-pll.txt | 8 ++++---- drivers/clk/keystone/pll.c | 20 ++++++++++++++++++-- 2 files changed, 22 insertions(+), 6 deletions(-) diff --git a/Documentation/devicetree/bindings/clock/keystone-pll.txt b/Documentation/devicetree/bindings/clock/keystone-pll.txt index 225990f..47570d2 100644 --- a/Documentation/devicetree/bindings/clock/keystone-pll.txt +++ b/Documentation/devicetree/bindings/clock/keystone-pll.txt @@ -15,8 +15,8 @@ Required properties: - compatible : shall be "ti,keystone,main-pll-clock" or "ti,keystone,pll-clock" - clocks : parent clock phandle - reg - pll control0 and pll multipler registers -- reg-names : control and multiplier. The multiplier is applicable only for - main pll clock +- reg-names : control, multiplier and post-divider. The multiplier and + post-divider registers are applicable only for main pll clock - fixed-postdiv : fixed post divider value. If absent, use clkod register bits for postdiv @@ -25,8 +25,8 @@ Example: #clock-cells = <0>; compatible = "ti,keystone,main-pll-clock"; clocks = <&refclksys>; - reg = <0x02620350 4>, <0x02310110 4>; - reg-names = "control", "multiplier"; + reg = <0x02620350 4>, <0x02310110 4>, <0x02310108 4>; + reg-names = "control", "multiplier", "post-divider"; fixed-postdiv = <2>; }; diff --git a/drivers/clk/keystone/pll.c b/drivers/clk/keystone/pll.c index 0dd8a4b..4a375ea 100644 --- a/drivers/clk/keystone/pll.c +++ b/drivers/clk/keystone/pll.c @@ -37,7 +37,8 @@ * Main PLL or any other PLLs in the device such as ARM PLL, DDR PLL * or PA PLL available on keystone2. These PLLs are controlled by * this register. Main PLL is controlled by a PLL controller. - * @pllm: PLL register map address + * @pllm: PLL register map address for multiplier bits + * @pllod: PLL register map address for post divider bits * @pll_ctl0: PLL controller map address * @pllm_lower_mask: multiplier lower mask * @pllm_upper_mask: multiplier upper mask @@ -53,6 +54,7 @@ struct clk_pll_data { u32 phy_pllm; u32 phy_pll_ctl0; void __iomem *pllm; + void __iomem *pllod; void __iomem *pll_ctl0; u32 pllm_lower_mask; u32 pllm_upper_mask; @@ -102,7 +104,11 @@ static unsigned long clk_pllclk_recalc(struct clk_hw *hw, /* read post divider from od bits*/ postdiv = ((val & pll_data->clkod_mask) >> pll_data->clkod_shift) + 1; - else + else if (pll_data->pllod) { + postdiv = readl(pll_data->pllod); + postdiv = ((postdiv & pll_data->clkod_mask) >> + pll_data->clkod_shift) + 1; + } else postdiv = pll_data->postdiv; rate /= (prediv + 1); @@ -172,12 +178,21 @@ static void __init _of_pll_clk_init(struct device_node *node, bool pllctrl) /* assume the PLL has output divider register bits */ pll_data->clkod_mask = CLKOD_MASK; pll_data->clkod_shift = CLKOD_SHIFT; + + /* + * Check if there is an post-divider register. If not + * assume od bits are part of control register. + */ + i = of_property_match_string(node, "reg-names", + "post-divider"); + pll_data->pllod = of_iomap(node, i); } i = of_property_match_string(node, "reg-names", "control"); pll_data->pll_ctl0 = of_iomap(node, i); if (!pll_data->pll_ctl0) { pr_err("%s: ioremap failed\n", __func__); + iounmap(pll_data->pllod); goto out; } @@ -193,6 +208,7 @@ static void __init _of_pll_clk_init(struct device_node *node, bool pllctrl) pll_data->pllm = of_iomap(node, i); if (!pll_data->pllm) { iounmap(pll_data->pll_ctl0); + iounmap(pll_data->pllod); goto out; } } -- 1.9.1 -- To unsubscribe from this list: send the line "unsubscribe devicetree" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html