This patch add support for the imx6dl based aristainetos2 board
with following configuration:
CPU: Freescale i.MX6DL rev1.1 at 792 MHz
MReset cause: POR
MBoard: aristaitenos2
DRAM: 1 GiB
NAND: 1024 MiB
MMC: FSL_SDHC: 0, FSL_SDHC: 1
SF: Detected N25Q128A with page size 256 Bytes, erase size 64 KiB, total 16 MiB
Display: lb07wv8 (800x480)
As this board can used with 2 different display types, the
differences between them are extracted into 2 DTS files, and
the common settings are collected in a common file.
Signed-off-by: Heiko Schocher <hs@xxxxxxx>
---
Changes in v4:
- add comments from Philipp Zabel:
- fix some typos
- fix license text
- fix pmic compatible name to "dlg,da9063"
- remove clocks property from i2c4 node
- use simple panel driver, so remove the fsl,data-mapping
and fsl,data-width properties and the display-timings node.
need patch: "drm/panel: Add support for LG LB070WV8 800x480 7" panel"
Changes in v3:
- add comments from Shawn Guo
- change license to GPL/X11 dual licence
- rename touch node name to "touch"
- add DTB in Makefile
- remove "status = "okay"" from backlight node
- rename "pinctrl_ipu1_1_80Ohm_clk" to "pinctrl_ipu_disp"
- remove "status = "okay"" from "display@di0" node
- remove "dma-names;" in ecspix nodes
- use macro for clock ID and gpio
- move iomuxc to the bottom of the file
- configure pinctrl_backlight in the device node, not from
the hog group
- provide a proper pad configuration value rather than 0x8000000.
- in the iomuxc node, save one level of the sub-node
needs patch:
LinusW queued patch 5fcdf6a7ed95 ("pinctrl: imx: Allow
parsing DT without function nodes")
- add comments from Philipp Zabel
- get rid of "fsl,panel" to connect a drm_panel to the parallel-display
instead switch to the common of-graph bindings.
need patch: "drm/imx: parallel-display: fix drm_panel support"
from Philipp Zabel
Changes in v2:
- add comments from Sascha Hauer:
- remove "clock-frequency" property in i2c nodes
- correct indentation in some pinctrl nodes
- move pin settings out of "gpiogrp" where it was possible
led pins not moved, as they used through sysfs
arch/arm/boot/dts/Makefile | 2 +
arch/arm/boot/dts/imx6dl-aristainetos2_4.dts | 158 +++++++
arch/arm/boot/dts/imx6dl-aristainetos2_7.dts | 97 ++++
arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi | 632 +++++++++++++++++++++++++++
4 files changed, 889 insertions(+)
create mode 100644 arch/arm/boot/dts/imx6dl-aristainetos2_4.dts
create mode 100644 arch/arm/boot/dts/imx6dl-aristainetos2_7.dts
create mode 100644 arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 86217db..583fbeb 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -256,6 +256,8 @@ dtb-$(CONFIG_SOC_IMX53) += \
dtb-$(CONFIG_SOC_IMX6Q) += \
imx6dl-aristainetos_4.dtb \
imx6dl-aristainetos_7.dtb \
+ imx6dl-aristainetos2_4.dtb \
+ imx6dl-aristainetos2_7.dtb \
imx6dl-cubox-i.dtb \
imx6dl-dfi-fs700-m60.dtb \
imx6dl-gw51xx.dtb \
diff --git a/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts b/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts
new file mode 100644
index 0000000..ae50c8b
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-aristainetos2_4.dts
@@ -0,0 +1,158 @@
+/*
+ * Copyright (C) 2014 Rabeeh Khoury (rabeeh@xxxxxxxxxxxxx)
+ * Based on dt work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-aristainetos2.dtsi"
+
+/ {
+ model = "aristainetos2 i.MX6 Dual Lite Board 4";
+ compatible = "fsl,imx6dl";
+
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
+
+ display0: display@di0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx-parallel-display";
+ interface-pix-fmt = "rgb24";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ipu_disp>;
+
+ port@0 {
+ reg = <0>;
+ display0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_disp0>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ display_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&ecspi1 {
+ lcd_panel: display@0 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "lg,lg4573";
+ spi-max-frequency = <10000000>;
+ reg = <0>;
+ power-on-delay = <10>;
+
+ display-timings {
+ 480x800p57 {
+ native-mode;
+ clock-frequency = <27000027>;
+ hactive = <480>;
+ vactive = <800>;
+ hfront-porch = <10>;
+ hback-porch = <59>;
+ hsync-len = <10>;
+ vback-porch = <15>;
+ vfront-porch = <15>;
+ vsync-len = <15>;
+ hsync-active = <1>;
+ vsync-active = <1>;
+ };
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&display_out>;
+ };
+ };
+ };
+};
+
+&i2c3 {
+ touch: touch@4b {
+ compatible = "atmel,maxtouch";
+ reg = <0x4b>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <9 8>;
+ };
+};
+
+&ipu1_di0_disp0 {
+ remote-endpoint = <&display0_in>;
+};
+
+&iomuxc {
+ pinctrl_ipu_disp: ipudisp1grp {
+ fsl,pins = <
+ MX6QDL_PAD_DI0_DISP_CLK__IPU1_DI0_DISP_CLK 0x31
+ MX6QDL_PAD_DI0_PIN15__IPU1_DI0_PIN15 0xE1
+ MX6QDL_PAD_DI0_PIN2__IPU1_DI0_PIN02 0x10
+ MX6QDL_PAD_DI0_PIN3__IPU1_DI0_PIN03 0x10
+ MX6QDL_PAD_DISP0_DAT0__IPU1_DISP0_DATA00 0xE1
+ MX6QDL_PAD_DISP0_DAT1__IPU1_DISP0_DATA01 0xE1
+ MX6QDL_PAD_DISP0_DAT2__IPU1_DISP0_DATA02 0xE1
+ MX6QDL_PAD_DISP0_DAT3__IPU1_DISP0_DATA03 0xE1
+ MX6QDL_PAD_DISP0_DAT4__IPU1_DISP0_DATA04 0xE1
+ MX6QDL_PAD_DISP0_DAT5__IPU1_DISP0_DATA05 0xE1
+ MX6QDL_PAD_DISP0_DAT6__IPU1_DISP0_DATA06 0xE1
+ MX6QDL_PAD_DISP0_DAT7__IPU1_DISP0_DATA07 0xE1
+ MX6QDL_PAD_DISP0_DAT8__IPU1_DISP0_DATA08 0xE1
+ MX6QDL_PAD_DISP0_DAT9__IPU1_DISP0_DATA09 0xE1
+ MX6QDL_PAD_DISP0_DAT10__IPU1_DISP0_DATA10 0xE1
+ MX6QDL_PAD_DISP0_DAT11__IPU1_DISP0_DATA11 0xE1
+ MX6QDL_PAD_DISP0_DAT12__IPU1_DISP0_DATA12 0xE1
+ MX6QDL_PAD_DISP0_DAT13__IPU1_DISP0_DATA13 0xE1
+ MX6QDL_PAD_DISP0_DAT14__IPU1_DISP0_DATA14 0xe1
+ MX6QDL_PAD_DISP0_DAT15__IPU1_DISP0_DATA15 0xE1
+ MX6QDL_PAD_DISP0_DAT16__IPU1_DISP0_DATA16 0xE1
+ MX6QDL_PAD_DISP0_DAT17__IPU1_DISP0_DATA17 0xE1
+ MX6QDL_PAD_DISP0_DAT18__IPU1_DISP0_DATA18 0xE1
+ MX6QDL_PAD_DISP0_DAT19__IPU1_DISP0_DATA19 0xE1
+ MX6QDL_PAD_DISP0_DAT20__IPU1_DISP0_DATA20 0xE1
+ MX6QDL_PAD_DISP0_DAT21__IPU1_DISP0_DATA21 0xE1
+ MX6QDL_PAD_DISP0_DAT22__IPU1_DISP0_DATA22 0xE1
+ MX6QDL_PAD_DISP0_DAT23__IPU1_DISP0_DATA23 0xE1
+ >;
+ };
+};
diff --git a/arch/arm/boot/dts/imx6dl-aristainetos2_7.dts b/arch/arm/boot/dts/imx6dl-aristainetos2_7.dts
new file mode 100644
index 0000000..7500562
--- /dev/null
+++ b/arch/arm/boot/dts/imx6dl-aristainetos2_7.dts
@@ -0,0 +1,97 @@
+/*
+ * Copyright (C) 2014 Rabeeh Khoury (rabeeh@xxxxxxxxxxxxx)
+ * Based on dt work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "imx6dl.dtsi"
+#include "imx6qdl-aristainetos2.dtsi"
+
+/ {
+ model = "aristainetos2 i.MX6 Dual Lite Board 7";
+ compatible = "fsl,imx6dl";
+
+ memory {
+ reg = <0x10000000 0x40000000>;
+ };
+
+ panel: panel {
+ compatible = "lg,lb070wv8";
+ backlight = <&backlight>;
+ enable-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&i2c3 {
+ touch: touch@4d {
+ compatible = "atmel,maxtouch";
+ reg = <0x4d>;
+ interrupt-parent = <&gpio2>;
+ interrupts = <9 8>;
+ };
+};
+
+&ldb {
+ status = "okay";
+
+ lvds-channel@0 {
+ status = "okay";
+
+ port@0 {
+ reg = <0>;
+ lvds0_in: endpoint {
+ remote-endpoint = <&ipu1_di0_lvds0>;
+ };
+ };
+
+ port@4 {
+ reg = <4>;
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+
+ };
+};
diff --git a/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi b/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
new file mode 100644
index 0000000..a15e77d
--- /dev/null
+++ b/arch/arm/boot/dts/imx6qdl-aristainetos2.dtsi
@@ -0,0 +1,632 @@
+/*
+ * Copyright (C) 2014 Rabeeh Khoury (rabeeh@xxxxxxxxxxxxx)
+ * Based on dt work by Russell King
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx6qdl-clock.h>
+
+/ {
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm1 0 5000000>;
+ brightness-levels = <0 4 8 16 32 64 128 255>;
+ default-brightness-level = <7>;
+ enable-gpios = <&gpio6 31 GPIO_ACTIVE_HIGH>;
+ };
+
+ regulators {
+ compatible = "simple-bus";
+
+ reg_2p5v: 2p5v {
+ compatible = "regulator-fixed";
+ regulator-name = "2P5V";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-always-on;
+ };
+
+ reg_3p3v: 3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ reg_usbh1_vbus: usb-h1-vbus {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio1 0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_aristainetos2_usbh1_vbus>;
+ regulator-name = "usb_h1_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ reg_usbotg_vbus: usb-otg-vbus {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio4 15 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_aristainetos2_usbotg_vbus>;
+ regulator-name = "usb_otg_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+ };
+};
+
+&audmux {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_audmux>;
+ status = "okay";
+};
+
+&can1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan1>;
+ status = "okay";
+};
+
+&can2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flexcan2>;
+ status = "okay";
+};
+
+&ecspi1 {
+ fsl,spi-num-chipselects = <3>;
+ cs-gpios = <&gpio4 9 GPIO_ACTIVE_HIGH
+ &gpio4 10 GPIO_ACTIVE_HIGH
+ &gpio4 11 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi1>;
+ status = "okay";
+};
+
+&ecspi2 {
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <&gpio2 26 GPIO_ACTIVE_HIGH &gpio2 27 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi2>;
+ status = "okay";
+};
+
+&ecspi4 {
+ fsl,spi-num-chipselects = <2>;
+ cs-gpios = <&gpio3 29 GPIO_ACTIVE_HIGH &gpio5 2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_ecspi4>;
+ status = "okay";
+
+ flash: m25p80@1 {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "micron,n25q128a11";
+ spi-max-frequency = <20000000>;
+ reg = <1>;
+ };
+};
+
+&i2c1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1>;
+ status = "okay";
+
+ pmic@58 {
+ compatible = "dlg,da9063";
+ reg = <0x58>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <04 0x8>;
+
+ regulators {
+ bcore1 {
+ regulator-name = "bcore1";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ bcore2 {
+ regulator-name = "bcore2";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ bpro {
+ regulator-name = "bpro";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ bperi {
+ regulator-name = "bperi";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ bmem {
+ regulator-name = "bmem";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo2 {
+ regulator-name = "ldo2";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo3 {
+ regulator-name = "ldo3";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo4 {
+ regulator-name = "ldo4";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo5 {
+ regulator-name = "ldo5";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo6 {
+ regulator-name = "ldo6";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo7 {
+ regulator-name = "ldo7";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo8 {
+ regulator-name = "ldo8";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo9 {
+ regulator-name = "ldo9";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo10 {
+ regulator-name = "ldo10";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo11 {
+ regulator-name = "ldo11";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ bio {
+ regulator-name = "bio";
+ regulator-always-on = <1>;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+ };
+ };
+
+ tmp103: tmp103@71 {
+ compatible = "ti,tmp103";
+ reg = <0x71>;
+ };
+};
+
+&i2c2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c2>;
+ status = "okay";
+};
+
+&i2c3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c3>;
+ status = "okay";
+
+ expander: tca6416@20 {
+ compatible = "ti,tca6416";
+ reg = <0x20>;
+ #gpio-cells = <2>;
+ gpio-controller;
+ };
+
+ rtc@68 {
+ compatible = "dallas,m41t00";
+ reg = <0x68>;
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c4>;
+ status = "okay";
+
+ eeprom@50{
+ compatible = "atmel,24c64";
+ reg = <0x50>;
+ };
+
+ eeprom@57{
+ compatible = "atmel,24c64";
+ reg = <0x57>;
+ };
+};
+
+&fec {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_enet>;
+ phy-mode = "rgmii";
+ phy-reset-gpios = <&gpio7 18 GPIO_ACTIVE_HIGH>;
+ txd0-skew-ps = <0>;
+ txd1-skew-ps = <0>;
+ txd2-skew-ps = <0>;
+ txd3-skew-ps = <0>;
+ status = "okay";
+};
+
+&gpmi {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpmi_nand>;
+ status = "okay";
+};
+
+&pcie {
+ reset-gpio = <&gpio2 16 GPIO_ACTIVE_HIGH>;
+ status = "okay";
+};
+
+&pwm1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm1>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1>;
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart2>;
+ status = "okay";
+};
+
+&uart3 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3>;
+ fsl,uart-has-rtscts;
+ status = "okay";
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart4>;
+ status = "okay";
+};
+
+&usbh1 {
+ vbus-supply = <®_usbh1_vbus>;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbotg {
+ vbus-supply = <®_usbotg_vbus>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usbotg>;
+ disable-over-current;
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usdhc1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc1>;
+ cd-gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&usdhc2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usdhc2>;
+ cd-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>;
+ wp-gpios = <&gpio2 10 GPIO_ACTIVE_HIGH>;
+ no-1-8-v;
+ status = "okay";
+};
+
+&iomuxc {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio>;
+
+ pinctrl_audmux: audmux {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT7__AUD3_RXD 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT4__AUD3_TXC 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT5__AUD3_TXD 0x1b0b0
+ MX6QDL_PAD_CSI0_DAT6__AUD3_TXFS 0x1b0b0
+ >;
+ };
+
+ pinctrl_ecspi1: ecspi1grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D17__ECSPI1_MISO 0x100b1
+ MX6QDL_PAD_EIM_D18__ECSPI1_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D16__ECSPI1_SCLK 0x100b1
+ MX6QDL_PAD_KEY_ROW1__GPIO4_IO09 0x100b1 /* SS0# */
+ MX6QDL_PAD_KEY_COL2__GPIO4_IO10 0x100b1 /* SS1# */
+ MX6QDL_PAD_KEY_ROW2__GPIO4_IO11 0x100b1 /* SS2# */
+ >;
+ };
+
+ pinctrl_ecspi2: ecspi2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_OE__ECSPI2_MISO 0x100b1
+ MX6QDL_PAD_EIM_CS0__ECSPI2_SCLK 0x100b1
+ MX6QDL_PAD_EIM_CS1__ECSPI2_MOSI 0x100b1
+ MX6QDL_PAD_EIM_RW__GPIO2_IO26 0x100b1 /* SS0# */
+ MX6QDL_PAD_EIM_LBA__GPIO2_IO27 0x100b1 /* SS1# */
+ >;
+ };
+
+ pinctrl_ecspi4: ecspi4grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D21__ECSPI4_SCLK 0x100b1
+ MX6QDL_PAD_EIM_D22__ECSPI4_MISO 0x100b1
+ MX6QDL_PAD_EIM_D28__ECSPI4_MOSI 0x100b1
+ MX6QDL_PAD_EIM_D29__GPIO3_IO29 0x100b1 /* SS0# */
+ MX6QDL_PAD_EIM_A25__GPIO5_IO02 0x100b1 /* SS1# */
+ MX6QDL_PAD_SD4_DAT7__GPIO2_IO15 0x1b0b0 /* WP pin */
+ >;
+ };
+
+ pinctrl_enet: enetgrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_MDIO__ENET_MDIO 0x1b0b0
+ MX6QDL_PAD_ENET_MDC__ENET_MDC 0x1b0b0
+ MX6QDL_PAD_RGMII_TXC__RGMII_TXC 0x1b0b0
+ MX6QDL_PAD_RGMII_TD0__RGMII_TD0 0x1b0b0
+ MX6QDL_PAD_RGMII_TD1__RGMII_TD1 0x1b0b0
+ MX6QDL_PAD_RGMII_TD2__RGMII_TD2 0x1b0b0
+ MX6QDL_PAD_RGMII_TD3__RGMII_TD3 0x1b0b0
+ MX6QDL_PAD_RGMII_TX_CTL__RGMII_TX_CTL 0x1b0b0
+ MX6QDL_PAD_ENET_REF_CLK__ENET_TX_CLK 0x1b0b0
+ MX6QDL_PAD_RGMII_RXC__RGMII_RXC 0x1b0b0
+ MX6QDL_PAD_RGMII_RD0__RGMII_RD0 0x1b0b0
+ MX6QDL_PAD_RGMII_RD1__RGMII_RD1 0x1b0b0
+ MX6QDL_PAD_RGMII_RD2__RGMII_RD2 0x1b0b0
+ MX6QDL_PAD_RGMII_RD3__RGMII_RD3 0x1b0b0
+ MX6QDL_PAD_RGMII_RX_CTL__RGMII_RX_CTL 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan1: flexcan1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_CLK__FLEXCAN1_RX 0x1b0b0
+ MX6QDL_PAD_SD3_CMD__FLEXCAN1_TX 0x1b0b0
+ >;
+ };
+
+ pinctrl_flexcan2: flexcan2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD3_DAT0__FLEXCAN2_TX 0x1b0b0
+ MX6QDL_PAD_SD3_DAT1__FLEXCAN2_RX 0x1b0b0
+ >;
+ };
+
+ pinctrl_gpio: gpiogrp {
+ fsl,pins = <
+ MX6QDL_PAD_ENET_CRS_DV__GPIO1_IO25 0x1b0b0 /* led enable */
+ MX6QDL_PAD_NANDF_CS2__GPIO6_IO15 0x1b0b0 /* LCD power enable */
+ MX6QDL_PAD_NANDF_CS3__GPIO6_IO16 0x1b0b0 /* led yellow */
+ MX6QDL_PAD_EIM_EB0__GPIO2_IO28 0x1b0b0 /* led red */
+ MX6QDL_PAD_EIM_A24__GPIO5_IO04 0x1b0b0 /* led green */
+ MX6QDL_PAD_EIM_EB1__GPIO2_IO29 0x1b0b0 /* led blue */
+ MX6QDL_PAD_SD3_DAT5__GPIO7_IO00 0x1b0b0 /* Profibus IRQ */
+ MX6QDL_PAD_SD3_DAT6__GPIO6_IO18 0x1b0b0 /* FPGA IRQ */
+ MX6QDL_PAD_EIM_A23__GPIO6_IO06 0x1b0b0 /* spi bus #2 SS driver enable */
+ MX6QDL_PAD_GPIO_18__GPIO7_IO13 0x1b0b0 /* RST_LOC# PHY reset input (has pull-down!)*/
+ MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID 0x1b0b0 /* USB_OTG_ID = GPIO1_24*/
+ MX6QDL_PAD_SD4_DAT1__GPIO2_IO09 0x1b0b0 /* Touchscreen IRQ */
+ MX6QDL_PAD_EIM_A22__GPIO2_IO16 0x1b0b0 /* PCIe reset */
+ >;
+ };
+
+ pinctrl_gpmi_nand: gpmi-nand {
+ fsl,pins = <
+ MX6QDL_PAD_NANDF_CLE__NAND_CLE 0xb0b1
+ MX6QDL_PAD_NANDF_ALE__NAND_ALE 0xb0b1
+ MX6QDL_PAD_NANDF_WP_B__NAND_WP_B 0xb0b1
+ MX6QDL_PAD_NANDF_RB0__NAND_READY_B 0xb000
+ MX6QDL_PAD_NANDF_CS0__NAND_CE0_B 0xb0b1
+ MX6QDL_PAD_SD4_CMD__NAND_RE_B 0xb0b1
+ MX6QDL_PAD_SD4_CLK__NAND_WE_B 0xb0b1
+ MX6QDL_PAD_NANDF_D0__NAND_DATA00 0xb0b1
+ MX6QDL_PAD_NANDF_D1__NAND_DATA01 0xb0b1
+ MX6QDL_PAD_NANDF_D2__NAND_DATA02 0xb0b1
+ MX6QDL_PAD_NANDF_D3__NAND_DATA03 0xb0b1
+ MX6QDL_PAD_NANDF_D4__NAND_DATA04 0xb0b1
+ MX6QDL_PAD_NANDF_D5__NAND_DATA05 0xb0b1
+ MX6QDL_PAD_NANDF_D6__NAND_DATA06 0xb0b1
+ MX6QDL_PAD_NANDF_D7__NAND_DATA07 0xb0b1
+ >;
+ };
+
+ pinctrl_i2c1: i2c1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT8__I2C1_SDA 0x4001b8b1
+ MX6QDL_PAD_CSI0_DAT9__I2C1_SCL 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c2: i2c2grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL3__I2C2_SCL 0x4001b8b1
+ MX6QDL_PAD_KEY_ROW3__I2C2_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c3: i2c3grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_5__I2C3_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_6__I2C3_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_i2c4: i2c4grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_7__I2C4_SCL 0x4001b8b1
+ MX6QDL_PAD_GPIO_8__I2C4_SDA 0x4001b8b1
+ >;
+ };
+
+ pinctrl_pwm1: pwm1grp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__PWM1_OUT 0x1b0b0
+ MX6QDL_PAD_EIM_BCLK__GPIO6_IO31 0x1b0b0 /* backlight enable */
+ >;
+ };
+
+ pinctrl_uart1: uart1grp {
+ fsl,pins = <
+ MX6QDL_PAD_CSI0_DAT10__UART1_TX_DATA 0x1b0b1
+ MX6QDL_PAD_CSI0_DAT11__UART1_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D20__UART1_RTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D19__UART1_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart2: uart2grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D26__UART2_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D27__UART2_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart3: uart3grp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_D24__UART3_TX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D25__UART3_RX_DATA 0x1b0b1
+ MX6QDL_PAD_EIM_D31__UART3_RTS_B 0x1b0b1
+ MX6QDL_PAD_EIM_D23__UART3_CTS_B 0x1b0b1
+ >;
+ };
+
+ pinctrl_uart4: uart4grp {
+ fsl,pins = <
+ MX6QDL_PAD_KEY_COL0__UART4_TX_DATA 0x1b0b1
+ MX6QDL_PAD_KEY_ROW0__UART4_RX_DATA 0x1b0b1
+ >;
+ };
+
+ pinctrl_usbotg: usbotggrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_1__USB_OTG_ID 0x17059
+ >;
+ };
+
+ pinctrl_aristainetos2_usbh1_vbus: aristainetos-usbh1-vbus {
+ fsl,pins = <MX6QDL_PAD_GPIO_0__USB_H1_PWR 0x130b0>;
+ };
+
+ pinctrl_aristainetos2_usbotg_vbus: aristainetos-usbotg-vbus {
+ fsl,pins = <MX6QDL_PAD_KEY_ROW4__USB_OTG_PWR 0x130b0>;
+ };
+
+ pinctrl_usdhc1: usdhc1grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD1_CMD__SD1_CMD 0x17059
+ MX6QDL_PAD_SD1_CLK__SD1_CLK 0x10059
+ MX6QDL_PAD_SD1_DAT0__SD1_DATA0 0x17059
+ MX6QDL_PAD_SD1_DAT1__SD1_DATA1 0x17059
+ MX6QDL_PAD_SD1_DAT2__SD1_DATA2 0x17059
+ MX6QDL_PAD_SD1_DAT3__SD1_DATA3 0x17059
+ MX6QDL_PAD_ENET_RXD0__GPIO1_IO27 0x1b0b0 /* SD1 card detect input */
+ MX6QDL_PAD_DI0_PIN4__GPIO4_IO20 0x1b0b0 /* SD1 write protect input */
+ >;
+ };
+
+ pinctrl_usdhc2: usdhc2grp {
+ fsl,pins = <
+ MX6QDL_PAD_SD2_CMD__SD2_CMD 0x71
+ MX6QDL_PAD_SD2_CLK__SD2_CLK 0x71
+ MX6QDL_PAD_SD2_DAT0__SD2_DATA0 0x71
+ MX6QDL_PAD_SD2_DAT1__SD2_DATA1 0x71
+ MX6QDL_PAD_SD2_DAT2__SD2_DATA2 0x71
+ MX6QDL_PAD_SD2_DAT3__SD2_DATA3 0x71
+ MX6QDL_PAD_SD3_RST__GPIO7_IO08 0x1b0b0 /* SD2 level shifter output enable */
+ MX6QDL_PAD_GPIO_19__GPIO4_IO05 0x1b0b0 /* SD2 card detect input */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* SD2 write protect input */
+ >;
+ };
+};
--
2.1.0
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
