This patch adds documentation for a pinctrl-names property.
The property, when present, is used for switching the source
of the strobe signal for the device.
Signed-off-by: Jacek Anaszewski <j.anaszewski@xxxxxxxxxxx>
Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
Cc: Bryan Wu <cooloney@xxxxxxxxx>
Cc: Richard Purdie <rpurdie@xxxxxxxxx>
Cc: Sakari Ailus <sakari.ailus@xxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx
---
.../devicetree/bindings/leds/leds-aat1290.txt | 36 ++++++++++++++++++--
1 file changed, 34 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/leds/leds-aat1290.txt b/Documentation/devicetree/bindings/leds/leds-aat1290.txt
index ef88b9c..c05ed91 100644
--- a/Documentation/devicetree/bindings/leds/leds-aat1290.txt
+++ b/Documentation/devicetree/bindings/leds/leds-aat1290.txt
@@ -2,7 +2,9 @@
The device is controlled through two pins: FL_EN and EN_SET. The pins when,
asserted high, enable flash strobe and movie mode (max 1/2 of flash current)
-respectively.
+respectively. In order to add a capability of selecting the strobe signal source
+(e.g. CPU or camera sensor) there is an additional switch required, independent
+of the flash chip. The switch is controlled with pin control.
Required properties:
@@ -10,6 +12,13 @@ Required properties:
- flen-gpios : Must be device tree identifier of the flash device FL_EN pin.
- enset-gpios : Must be device tree identifier of the flash device EN_SET pin.
+Optional properties:
+- pinctrl-names : Must contain entries: "default", "host", "isp". Entries
+ "default" and "host" must refer to the same pin configuration
+ node, which sets the host as a strobe signal provider. Entry
+ "isp" must refer to the pin configuration node, which sets the
+ ISP as a strobe signal provider.
+
A discrete LED element connected to the device must be represented by a child
node - see Documentation/devicetree/bindings/leds/common.txt.
@@ -25,13 +34,22 @@ Required properties of the LED child node:
Optional properties of the LED child node:
- label : see Documentation/devicetree/bindings/leds/common.txt
-Example (by Ct = 220nF, Rset = 160kohm):
+Example (by Ct = 220nF, Rset = 160kohm and exynos4412-trats2 board with
+a switch that allows for routing strobe signal either from the host or from
+the camera sensor):
+
+#include "exynos4412.dtsi"
aat1290 {
compatible = "skyworks,aat1290";
flen-gpios = <&gpj1 1 GPIO_ACTIVE_HIGH>;
enset-gpios = <&gpj1 2 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default", "host", "isp";
+ pinctrl-0 = <&camera_flash_host>;
+ pinctrl-1 = <&camera_flash_host>;
+ pinctrl-2 = <&camera_flash_isp>;
+
camera_flash: flash-led {
label = "aat1290-flash";
led-max-microamp = <520833>;
@@ -39,3 +57,17 @@ aat1290 {
flash-timeout-us = <1940000>;
};
};
+
+&pinctrl_0 {
+ camera_flash_host: camera-flash-host {
+ samsung,pins = "gpj1-0";
+ samsung,pin-function = <1>;
+ samsung,pin-val = <0>;
+ };
+
+ camera_flash_isp: camera-flash-isp {
+ samsung,pins = "gpj1-0";
+ samsung,pin-function = <1>;
+ samsung,pin-val = <1>;
+ };
+};
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
