Re: [PATCH v4 1/1] ARM: mvebu: dts: Add dts file for DLink DNS-327L

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 20.05.2015 12:20, Andrew wrote:
Sebastian Hesselbarth писал 20.05.2015 12:05:
On 19.05.2015 23:10, Andrew Andrianov wrote:
DNS-327L is a 2-bay NAS with the following specs:
[...]
Signed-off-by: Andrew Andrianov <andrew@xxxxxxxxxx>
---
  arch/arm/boot/dts/Makefile                     |   1 +
  arch/arm/boot/dts/armada-370-dlink-dns327l.dts | 356
+++++++++++++++++++++++++
  2 files changed, 357 insertions(+)
  create mode 100644 arch/arm/boot/dts/armada-370-dlink-dns327l.dts
[...]
diff --git a/arch/arm/boot/dts/armada-370-dlink-dns327l.dts
b/arch/arm/boot/dts/armada-370-dlink-dns327l.dts
new file mode 100644
index 0000000..0f4555c4
--- /dev/null
+++ b/arch/arm/boot/dts/armada-370-dlink-dns327l.dts
@@ -0,0 +1,356 @@
[...]
+    regulators {
+        compatible = "simple-bus";
+        #address-cells = <1>;
+        #size-cells = <0>;
+        pinctrl-0 = <&xhci_pwr_pin
+            &sata_l_pwr_pin
+            &sata_r_pwr_pin>;
+
+        pinctrl-names = "default";

I doubt pinctrl will not work as you expected. For regulators, unlike
gpio-keys/leds above, this node just describes the "bus" of regulators.

Are you sure about this moment? FYI: I've taken
armada-370-synology-ds213j.dts
as the reference which happens to list regulator pinctrl (As of 4.1-rc1)
just the same way:

     compatible = "simple-bus";
         #address-cells = <1>;
         #size-cells = <0>;
         pinctrl-0 = <&sata1_pwr_pin &sata2_pwr_pin>;
         pinctrl-names = "default";
                 ...

Well, even if it works the pinctrl should be claimed by the device that
actually depends on it, i.e. the regulator itself.

If that's erroneous we should fix armada-370-synology-ds213j.dts as well.

Most likely nobody ever noticed if that didn't work because (a) usually
gpio functions are setup by the bootloader or (b) gpio is default reset
value of the pinctrl registers anyway.

I'd say move the pinctrl properties to regulator nodes for dns-327l now
and we move the properties for ds213j in a separate patch.

Sebastian

+
+        usb_power: regulator@1 {
+            compatible = "regulator-fixed";
+            reg = <1>;
+            regulator-name = "USB3.0 Port Power";
+            regulator-min-microvolt = <5000000>;
+            regulator-max-microvolt = <5000000>;
+            enable-active-high;
+            regulator-boot-on;
+            regulator-always-on;
+            gpio = <&gpio0 13 GPIO_ACTIVE_HIGH>;

Instead you'll have to put the corresponding pinctrl-0/names properties
in each of the regulator nodes, i.e.

        pinctrl-0 = <&xhci_pwr_pin>
        pinctrl-names = "default";

here and similar for the other regulator nodes.

+        };
+
+        sata_r_power: regulator@2 {
+            compatible = "regulator-fixed";
+            reg = <2>;
+            regulator-name = "SATA-R Power";
+            regulator-min-microvolt = <5000000>;
+            regulator-max-microvolt = <5000000>;
+            startup-delay-us = <2000000>;
+            enable-active-high;
+            regulator-always-on;
+            regulator-boot-on;
+            gpio = <&gpio1 22 GPIO_ACTIVE_HIGH>;
+        };
+
+        sata_l_power: regulator@3 {
+            compatible = "regulator-fixed";
+            reg = <3>;
+            regulator-name = "SATA-L Power";
+            regulator-min-microvolt = <5000000>;
+            regulator-max-microvolt = <5000000>;
+            startup-delay-us = <4000000>;
+            enable-active-high;
+            regulator-always-on;
+            regulator-boot-on;
+            gpio = <&gpio1 24 GPIO_ACTIVE_HIGH>;
+        };
+    };
+};


--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux