On Wed, May 06, 2015 at 10:59:45AM -0700, Brian Norris wrote:
> These are already-documented common bindings for NAND chips. Let's
> handle them in nand_base.
>
> If NAND controller drivers need to act on this data before bringing up
> the NAND chip (e.g., fill out ECC callback functions, change HW modes,
> etc.), then they can do so between calling nand_scan_ident() and
> nand_scan_tail().
>
> Signed-off-by: Brian Norris <computersforpeace@xxxxxxxxx>
Pushed just this patch to l2-mtd.git, since it's relatively
uncontroversial and hasn't changed across the first three revisions. It
should be of benefit to a few other driver writers out there that I've
reviewed.
Brian
> ---
> drivers/mtd/nand/nand_base.c | 41 +++++++++++++++++++++++++++++++++++++++++
> include/linux/mtd/nand.h | 5 +++++
> 2 files changed, 46 insertions(+)
>
> diff --git a/drivers/mtd/nand/nand_base.c b/drivers/mtd/nand/nand_base.c
> index c2e1232cd45c..c6cf775ee431 100644
> --- a/drivers/mtd/nand/nand_base.c
> +++ b/drivers/mtd/nand/nand_base.c
> @@ -48,6 +48,7 @@
> #include <linux/leds.h>
> #include <linux/io.h>
> #include <linux/mtd/partitions.h>
> +#include <linux/of_mtd.h>
>
> /* Define default oob placement schemes for large and small page devices */
> static struct nand_ecclayout nand_oob_8 = {
> @@ -3798,6 +3799,39 @@ ident_done:
> return type;
> }
>
> +static int nand_dt_init(struct mtd_info *mtd, struct nand_chip *chip,
> + struct device_node *dn)
> +{
> + int ecc_mode, ecc_strength, ecc_step;
> +
> + if (of_get_nand_bus_width(dn) == 16)
> + chip->options |= NAND_BUSWIDTH_16;
> +
> + if (of_get_nand_on_flash_bbt(dn))
> + chip->bbt_options |= NAND_BBT_USE_FLASH;
> +
> + ecc_mode = of_get_nand_ecc_mode(dn);
> + ecc_strength = of_get_nand_ecc_strength(dn);
> + ecc_step = of_get_nand_ecc_step_size(dn);
> +
> + if ((ecc_step >= 0 && !(ecc_strength >= 0)) ||
> + (!(ecc_step >= 0) && ecc_strength >= 0)) {
> + pr_err("must set both strength and step size in DT\n");
> + return -EINVAL;
> + }
> +
> + if (ecc_mode >= 0)
> + chip->ecc.mode = ecc_mode;
> +
> + if (ecc_strength >= 0)
> + chip->ecc.strength = ecc_strength;
> +
> + if (ecc_step > 0)
> + chip->ecc.size = ecc_step;
> +
> + return 0;
> +}
> +
> /**
> * nand_scan_ident - [NAND Interface] Scan for the NAND device
> * @mtd: MTD device structure
> @@ -3815,6 +3849,13 @@ int nand_scan_ident(struct mtd_info *mtd, int maxchips,
> int i, nand_maf_id, nand_dev_id;
> struct nand_chip *chip = mtd->priv;
> struct nand_flash_dev *type;
> + int ret;
> +
> + if (chip->dn) {
> + ret = nand_dt_init(mtd, chip, chip->dn);
> + if (ret)
> + return ret;
> + }
>
> /* Set the default functions */
> nand_set_defaults(chip, chip->options & NAND_BUSWIDTH_16);
> diff --git a/include/linux/mtd/nand.h b/include/linux/mtd/nand.h
> index 3d4ea7eb2b68..e0f40e12a2c8 100644
> --- a/include/linux/mtd/nand.h
> +++ b/include/linux/mtd/nand.h
> @@ -26,6 +26,8 @@
>
> struct mtd_info;
> struct nand_flash_dev;
> +struct device_node;
> +
> /* Scan and identify a NAND device */
> extern int nand_scan(struct mtd_info *mtd, int max_chips);
> /*
> @@ -542,6 +544,7 @@ struct nand_buffers {
> * flash device
> * @IO_ADDR_W: [BOARDSPECIFIC] address to write the 8 I/O lines of the
> * flash device.
> + * @dn: [BOARDSPECIFIC] device node describing this instance
> * @read_byte: [REPLACEABLE] read one byte from the chip
> * @read_word: [REPLACEABLE] read one word from the chip
> * @write_byte: [REPLACEABLE] write a single byte to the chip on the
> @@ -644,6 +647,8 @@ struct nand_chip {
> void __iomem *IO_ADDR_R;
> void __iomem *IO_ADDR_W;
>
> + struct device_node *dn;
> +
> uint8_t (*read_byte)(struct mtd_info *mtd);
> u16 (*read_word)(struct mtd_info *mtd);
> void (*write_byte)(struct mtd_info *mtd, uint8_t byte);
> --
> 1.9.1
>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
