On 20/03/2025 05:55, Wenbin Yao wrote:
From: Qiang Yu <quic_qianyu@xxxxxxxxxxx>
Add perst, wake and clkreq sideband signals and required regulators in
PCIe3 controller and PHY device tree node. Describe the voltage rails of
the x8 PCI slots for PCIe3 port.
Signed-off-by: Qiang Yu <quic_qianyu@xxxxxxxxxxx>
Signed-off-by: Wenbin Yao <quic_wenbyao@xxxxxxxxxxx>
---
arch/arm64/boot/dts/qcom/x1e80100-qcp.dts | 119 ++++++++++++++++++++++
1 file changed, 119 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
index 28086a2bc..9cd313802 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
+++ b/arch/arm64/boot/dts/qcom/x1e80100-qcp.dts
@@ -318,6 +318,48 @@ vreg_wcn_3p3: regulator-wcn-3p3 {
regulator-boot-on;
};
+ vreg_pcie_12v: regulator-pcie_12v {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_PCIE_12V";
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+
+ gpio = <&pm8550ve_8_gpios 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_x8_12v>;
+ };
+
+ vreg_pcie_3v3_aux: regulator-pcie_3v3_aux {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_PCIE_3P3_AUX";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmc8380_3_gpios 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pm_sde7_aux_3p3_en>;
+ };
+
+ vreg_pcie_3v3: regulator-pcie_3v3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_PCIE_3P3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pmc8380_3_gpios 6 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pm_sde7_main_3p3_en>;
+};
+
usb-1-ss0-sbu-mux {
compatible = "onnn,fsusb42", "gpio-sbu-mux";
@@ -907,6 +949,60 @@ &mdss_dp3_phy {
status = "okay";
};
+&pm8550ve_8_gpios {
+ pcie_x8_12v: pcie-12v-default-state {
+ pins = "gpio8";
+ function = "normal";
+ output-enable;
+ output-high;
+ bias-pull-down;
+ power-source = <0>;
+ };
+};
+
+&pmc8380_3_gpios {
+ pm_sde7_aux_3p3_en: pcie-aux-3p3-default-state {
+ pins = "gpio8";
+ function = "normal";
+ output-enable;
+ output-high;
+ bias-pull-down;
+ power-source = <0>;
+ };
+
+ pm_sde7_main_3p3_en: pcie-main-3p3-default-state {
+ pins = "gpio6";
+ function = "normal";
+ output-enable;
+ output-high;
+ bias-pull-down;
+ power-source = <0>;
+ };
+};
+
+&pcie3 {
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie3_default>;
+ perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&pcie3_phy {
+ vdda-phy-supply = <&vreg_l3j_0p8>;
+ vdda-pll-supply = <&vreg_l3e_1p2>;
+ vdda-qref-supply = <&vreg_l3c_0p8>;
+
+ status = "okay";
+};
+
+&pcie3port {
+ vpcie12v-supply = <&vreg_pcie_12v>;
+ vpcie3v3-supply = <&vreg_pcie_3v3>;
+ vpcie3v3aux-supply = <&vreg_pcie_3v3_aux>;
+};
+
&pcie4 {
perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
@@ -1118,6 +1214,29 @@ nvme_reg_en: nvme-reg-en-state {
bias-disable;
};
+ pcie3_default: pcie3-default-state {
+ clkreq-n-pins {
+ pins = "gpio144";
+ function = "pcie3_clk";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ perst-n-pins {
+ pins = "gpio143";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ wake-n-pins {
+ pins = "gpio145";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
pcie4_default: pcie4-default-state {
clkreq-n-pins {
pins = "gpio147";
--
2.34.1
Recommend breaking this patch into at least two patches @ the and
-> Add power control
-> Add sideband signals
if your patch title requires an and its usually a good indicator of a
place to break that patch into different parts.
---
bod
