According to code in drivers/pci/controller/dwc/pci-dra7xx.c
dra7xx_pcie_cpu_addr_fixup()
{
return cpu_addr & DRA7XX_CPU_TO_BUS_ADDR; //0x0FFFFFFF
}
PCI parent bus trim high 4 bits address to 0. Correct ranges in
target-module@51000000 to algin hardware behavior, which translate PCIe
outbound address 0..0x0fff_ffff to 0x2000_0000..0x2fff_ffff.
Set 'config' and 'addr_space' reg values to 0.
Change parent bus address of downstream I/O and non-prefetchable memory to
0.
Ensure no functional impact on the final address translation result.
Prepare for the removal of the driver’s cpu_addr_fixup().
Signed-off-by: Frank Li <Frank.Li@xxxxxxx>
---
arch/arm/boot/dts/ti/omap/dra7.dtsi | 18 +++++++++---------
1 file changed, 9 insertions(+), 9 deletions(-)
diff --git a/arch/arm/boot/dts/ti/omap/dra7.dtsi b/arch/arm/boot/dts/ti/omap/dra7.dtsi
index b709703f6c0d4..9213fdd25330b 100644
--- a/arch/arm/boot/dts/ti/omap/dra7.dtsi
+++ b/arch/arm/boot/dts/ti/omap/dra7.dtsi
@@ -196,7 +196,7 @@ axi0: target-module@51000000 {
#size-cells = <1>;
#address-cells = <1>;
ranges = <0x51000000 0x51000000 0x3000>,
- <0x20000000 0x20000000 0x10000000>;
+ <0x00000000 0x20000000 0x10000000>;
dma-ranges;
/**
* To enable PCI endpoint mode, disable the pcie1_rc
@@ -205,14 +205,14 @@ axi0: target-module@51000000 {
pcie1_rc: pcie@51000000 {
reg = <0x51000000 0x2000>,
<0x51002000 0x14c>,
- <0x20001000 0x2000>;
+ <0x00001000 0x2000>;
reg-names = "rc_dbics", "ti_conf", "config";
interrupts = <0 232 0x4>, <0 233 0x4>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
- ranges = <0x81000000 0 0x00000000 0x20003000 0 0x00010000>,
- <0x82000000 0 0x20013000 0x20013000 0 0x0ffed000>;
+ ranges = <0x81000000 0 0x00000000 0x00003000 0 0x00010000>,
+ <0x82000000 0 0x20013000 0x00013000 0 0x0ffed000>;
bus-range = <0x00 0xff>;
#interrupt-cells = <1>;
num-lanes = <1>;
@@ -238,7 +238,7 @@ pcie1_ep: pcie_ep@51000000 {
reg = <0x51000000 0x28>,
<0x51002000 0x14c>,
<0x51001000 0x28>,
- <0x20001000 0x10000000>;
+ <0x00001000 0x10000000>;
reg-names = "ep_dbics", "ti_conf", "ep_dbics2", "addr_space";
interrupts = <0 232 0x4>;
num-lanes = <1>;
@@ -270,20 +270,20 @@ axi1: target-module@51800000 {
#size-cells = <1>;
#address-cells = <1>;
ranges = <0x51800000 0x51800000 0x3000>,
- <0x30000000 0x30000000 0x10000000>;
+ <0x00000000 0x30000000 0x10000000>;
dma-ranges;
status = "disabled";
pcie2_rc: pcie@51800000 {
reg = <0x51800000 0x2000>,
<0x51802000 0x14c>,
- <0x30001000 0x2000>;
+ <0x00001000 0x2000>;
reg-names = "rc_dbics", "ti_conf", "config";
interrupts = <0 355 0x4>, <0 356 0x4>;
#address-cells = <3>;
#size-cells = <2>;
device_type = "pci";
- ranges = <0x81000000 0 0x00000000 0x30003000 0 0x00010000>,
- <0x82000000 0 0x30013000 0x30013000 0 0x0ffed000>;
+ ranges = <0x81000000 0 0x00000000 0x00003000 0 0x00010000>,
+ <0x82000000 0 0x30013000 0x00013000 0 0x0ffed000>;
bus-range = <0x00 0xff>;
#interrupt-cells = <1>;
num-lanes = <1>;
--
2.34.1
