The bootph-all and bootph-pre-ram tags were introduced in dt-schema (dtschema/schemas/bootph.yaml) to define node usage across different boot phases. Add boot phase tags to all required nodes to ensure boot support from all sources, including UART, USB (DFU), Ethernet, uSD card, eMMC, and OSPI NOR Flash. Signed-off-by: Wadim Egorov <w.egorov@xxxxxxxxx> --- v1: http://lists.infradead.org/pipermail/linux-arm-kernel/2025-February/1006239.html v2: - Add bootph-all to cpsw_port1 and main_pktma - Remove bootph-all from cpsw3g --- arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi | 15 +++++++++++++++ .../arm64/boot/dts/ti/k3-am62x-phyboard-lyra.dtsi | 9 +++++++++ 2 files changed, 24 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi index 2ef4cbaec789..effab2f810c2 100644 --- a/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi +++ b/arch/arm64/boot/dts/ti/k3-am62-phycore-som.dtsi @@ -29,6 +29,7 @@ aliases { memory@80000000 { device_type = "memory"; reg = <0x00000000 0x80000000 0x00000000 0x80000000>; + bootph-all; }; reserved_memory: reserved-memory { @@ -131,6 +132,7 @@ main_i2c0_pins_default: main-i2c0-default-pins { AM62X_IOPAD(0x1e0, PIN_INPUT_PULLUP, 0) /* (B16) I2C0_SCL */ AM62X_IOPAD(0x1e4, PIN_INPUT_PULLUP, 0) /* (A16) I2C0_SDA */ >; + bootph-all; }; main_mdio1_pins_default: main-mdio1-default-pins { @@ -138,6 +140,7 @@ main_mdio1_pins_default: main-mdio1-default-pins { AM62X_IOPAD(0x160, PIN_OUTPUT, 0) /* (AD24) MDIO0_MDC */ AM62X_IOPAD(0x15c, PIN_INPUT, 0) /* (AB22) MDIO0_MDIO */ >; + bootph-all; }; main_mmc0_pins_default: main-mmc0-default-pins { @@ -153,6 +156,7 @@ AM62X_IOPAD(0x200, PIN_INPUT_PULLUP, 0) /* (AC1) MMC0_DAT5 */ AM62X_IOPAD(0x1fc, PIN_INPUT_PULLUP, 0) /* (AD2) MMC0_DAT6 */ AM62X_IOPAD(0x1f8, PIN_INPUT_PULLUP, 0) /* (AC2) MMC0_DAT7 */ >; + bootph-all; }; main_rgmii1_pins_default: main-rgmii1-default-pins { @@ -170,6 +174,7 @@ AM62X_IOPAD(0x140, PIN_OUTPUT, 0) /* (AD18) RGMII1_TD3 */ AM62X_IOPAD(0x130, PIN_OUTPUT, 0) /* (AE19) RGMII1_TXC */ AM62X_IOPAD(0x12c, PIN_OUTPUT, 0) /* (AD19) RGMII1_TX_CTL */ >; + bootph-all; }; ospi0_pins_default: ospi0-default-pins { @@ -186,6 +191,7 @@ AM62X_IOPAD(0x024, PIN_INPUT, 0) /* (H25) OSPI0_D6 */ AM62X_IOPAD(0x028, PIN_INPUT, 0) /* (J22) OSPI0_D7 */ AM62X_IOPAD(0x008, PIN_INPUT, 0) /* (J24) OSPI0_DQS */ >; + bootph-all; }; pmic_irq_pins_default: pmic-irq-default-pins { @@ -210,6 +216,7 @@ &cpsw3g { &cpsw_port1 { phy-mode = "rgmii-rxid"; phy-handle = <&cpsw3g_phy1>; + bootph-all; }; &cpsw3g_mdio { @@ -220,6 +227,7 @@ &cpsw3g_mdio { cpsw3g_phy1: ethernet-phy@1 { compatible = "ethernet-phy-id2000.a231", "ethernet-phy-ieee802.3-c22"; reg = <1>; + bootph-all; ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; }; @@ -232,10 +240,15 @@ mbox_m4_0: mbox-m4-0 { }; }; +&main_pktdma { + bootph-all; +}; + &main_i2c0 { pinctrl-names = "default"; pinctrl-0 = <&main_i2c0_pins_default>; clock-frequency = <400000>; + bootph-all; status = "okay"; pmic@30 { @@ -355,6 +368,7 @@ serial_flash: flash@0 { cdns,tchsh-ns = <60>; cdns,tslch-ns = <60>; cdns,read-delay = <0>; + bootph-all; }; }; @@ -363,5 +377,6 @@ &sdhci0 { pinctrl-0 = <&main_mmc0_pins_default>; disable-wp; non-removable; + bootph-all; status = "okay"; }; diff --git a/arch/arm64/boot/dts/ti/k3-am62x-phyboard-lyra.dtsi b/arch/arm64/boot/dts/ti/k3-am62x-phyboard-lyra.dtsi index 922cad14c9f8..aab74d6019b0 100644 --- a/arch/arm64/boot/dts/ti/k3-am62x-phyboard-lyra.dtsi +++ b/arch/arm64/boot/dts/ti/k3-am62x-phyboard-lyra.dtsi @@ -138,6 +138,7 @@ vcc_3v3_mmc: regulator-vcc-3v3-mmc { regulator-max-microvolt = <3300000>; regulator-always-on; regulator-boot-on; + bootph-all; }; vcc_3v3_sw: regulator-vcc-3v3-sw { @@ -233,6 +234,7 @@ AM62X_IOPAD(0x228, PIN_INPUT_PULLUP, 0) /* (C21) MMC1_DAT2 */ AM62X_IOPAD(0x224, PIN_INPUT_PULLUP, 0) /* (D22) MMC1_DAT3 */ AM62X_IOPAD(0x240, PIN_INPUT_PULLUP, 0) /* (D17) MMC1_SDCD */ >; + bootph-all; }; main_rgmii2_pins_default: main-rgmii2-default-pins { @@ -257,6 +259,7 @@ main_uart0_pins_default: main-uart0-default-pins { AM62X_IOPAD(0x1c8, PIN_INPUT, 0) /* (D14) UART0_RXD */ AM62X_IOPAD(0x1cc, PIN_OUTPUT, 0) /* (E14) UART0_TXD */ >; + bootph-all; }; main_uart1_pins_default: main-uart1-default-pins { @@ -266,6 +269,7 @@ AM62X_IOPAD(0x198, PIN_OUTPUT, 2) /* (A19) MCASP0_AXR2.UART1_RTSn */ AM62X_IOPAD(0x1ac, PIN_INPUT, 2) /* (E19) MCASP0_AFSR.UART1_RXD */ AM62X_IOPAD(0x1b0, PIN_OUTPUT, 2) /* (A20) MCASP0_ACLKR.UART1_TXD */ >; + bootph-pre-ram; }; main_usb1_pins_default: main-usb1-default-pins { @@ -430,12 +434,14 @@ &main_mcan0 { &main_uart0 { pinctrl-names = "default"; pinctrl-0 = <&main_uart0_pins_default>; + bootph-all; status = "okay"; }; &main_uart1 { pinctrl-names = "default"; pinctrl-0 = <&main_uart1_pins_default>; + bootph-pre-ram; /* Main UART1 may be used by TIFS firmware */ status = "okay"; }; @@ -467,11 +473,13 @@ &sdhci1 { pinctrl-0 = <&main_mmc1_pins_default>; disable-wp; no-1-8-v; + bootph-all; status = "okay"; }; &usbss0 { ti,vbus-divider; + bootph-all; status = "okay"; }; @@ -482,6 +490,7 @@ &usbss1 { &usb0 { usb-role-switch; + bootph-all; port { typec_hs: endpoint { -- 2.34.1
