From: Peng Fan <peng.fan@xxxxxxx> Add i.MX95 Logical Machine Management and CPU Protocol documentation. Signed-off-by: Peng Fan <peng.fan@xxxxxxx> --- drivers/firmware/arm_scmi/vendors/imx/imx95.rst | 801 ++++++++++++++++++++++++ 1 file changed, 801 insertions(+) diff --git a/drivers/firmware/arm_scmi/vendors/imx/imx95.rst b/drivers/firmware/arm_scmi/vendors/imx/imx95.rst index b2dfd6c46ca2f5f12f0475c24cb54c060e9fa421..74326bf2ea8586282a735713e0ab7eb90ccce8ff 100644 --- a/drivers/firmware/arm_scmi/vendors/imx/imx95.rst +++ b/drivers/firmware/arm_scmi/vendors/imx/imx95.rst @@ -32,6 +32,501 @@ port, and deploy the SM on supported processors. The SM implements an interface compliant with the Arm SCMI Specification with additional vendor specific extensions. +SCMI_LMM: System Control and Management Logical Machine Management Vendor Protocol +================================================================================== + +This protocol is intended for boot, shutdown, and reset of other logical +machines (LM). It is usually used to allow one LM(e.g. OSPM) to manage +another LM which is usually an offload or accelerator engine.. Notifications +from this protocol can also be used to manage a communication link to another +LM. The LMM protocol provides functions to: + +- Describe the protocol version. +- Discover implementation attributes. +- Discover the LMs defined in the system. +- Boot an LM. +- Shutdown an LM (gracefully or forcibly). +- Reset an LM (gracefully or forcibly). +- Wake an LM from suspend. +- Suspend an LM (gracefully). +- Read boot/shutdown/reset information for an LM. +- Get notifications when an LM boots or shuts down (e.g. LM[X] requested + notification of LM[Y] boots or shuts down, when LM[Y] boots or shuts down, + SCMI firmware will send notification to LM[X]). + +'Graceful' means asking LM itself to shutdown/reset/etc (e.g. sending +notification to Linux, Then Linux reboots or powers down itself). It is async +command that the SUCCESS of the command just means the command successfully +return, not means reboot/reset successfully finished. +'Forceful' means the SM will force shutdown/reset/etc the LM. It is sync +command that the SUCCESS of the command means the LM has been successfully +shutdown/reset/etc. +If the commands not have Graceful/Forceful flag settings, such as WAKE, SUSEND, +it is async command. + +Commands: +_________ + +PROTOCOL_VERSION +~~~~~~~~~~~~~~~~ + +message_id: 0x0 +protocol_id: 0x80 +This command is mandatory. + ++---------------+--------------------------------------------------------------+ +|Return values | ++---------------+--------------------------------------------------------------+ +|Name |Description | ++---------------+--------------------------------------------------------------+ +|int32 status | See ARM SCMI Specification for status code definitions. | ++---------------+--------------------------------------------------------------+ +|uint32 version | For this revision of the specification, this value must be | +| | 0x10000. | ++---------------+--------------------------------------------------------------+ + +PROTOCOL_ATTRIBUTES +~~~~~~~~~~~~~~~~~~~ + +message_id: 0x1 +protocol_id: 0x80 +This command is mandatory. + ++------------------+-----------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status | See ARM SCMI Specification for status code definitions. | ++------------------+-----------------------------------------------------------+ +|uint32 attributes |Protocol attributes: | +| |Bits[31:8] Reserved, must be zero. | +| |Bits[7:0] Number of Logical Machines | ++------------------+-----------------------------------------------------------+ + +PROTOCOL_MESSAGE_ATTRIBUTES +~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +message_id: 0x2 +protocol_id: 0x80 +This command is mandatory. + ++------------------+-----------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status |SUCCESS: in case the message is implemented and available | +| |to use. | +| |NOT_FOUND: if the message identified by message_id is | +| |invalid or not implemented | ++------------------+-----------------------------------------------------------+ +|uint32 attributes |Flags that are associated with a specific function in the | +| |protocol. For all functions in this protocol, this | +| |parameter has a value of 0 | ++------------------+-----------------------------------------------------------+ + +LMM_ATTRIBUTES +~~~~~~~~~~~~~~ + +message_id: 0x3 +protocol_id: 0x80 +This command is mandatory. + ++------------------+-----------------------------------------------------------+ +|Parameters | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|uint32 lmid |ID of the Logical Machine | ++------------------+-----------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status |SUCCESS: if valid attributes are returned. | +| |NOT_FOUND: if lmId not points to a valid logical machine. | +| |DENIED: if the agent does not have permission to get info | +| |for the LM specified by lmid. | ++------------------+-----------------------------------------------------------+ +|uint32 lmid |Identifier of the LM whose identification is requested. | +| |This field is: Populated with the lmId of the calling | +| |agent, when the lmId parameter passed via the function is | +| |0xFFFFFFFF. Identical to the lmId field passed via the | +| |calling parameters, in all other cases | ++------------------+-----------------------------------------------------------+ +|uint32 attributes | Bits[31:0] reserved. must be zero | ++------------------+-----------------------------------------------------------+ +|uint32 state | Current state of the LM | ++------------------+-----------------------------------------------------------+ +|uint32 errStatus | Last error status recorded | ++------------------+-----------------------------------------------------------+ +|char name[16] | A NULL terminated ASCII string with the LM name, of up | +| | to 16 bytes | ++------------------+-----------------------------------------------------------+ + +LMM_BOOT +~~~~~~~~ + +message_id: 0x4 +protocol_id: 0x80 +This command is mandatory. + ++------------------+-----------------------------------------------------------+ +|Parameters | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|uint32 lmid |ID of the Logical Machine | ++------------------+-----------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status |SUCCESS: if LM boots successfully started. | +| |NOT_FOUND: if lmId not points to a valid logical machine. | +| |INVALID_PARAMETERS: if lmId is same as the caller. | +| |DENIED: if the agent does not have permission to manage the| +| |the LM specified by lmid. | ++------------------+-----------------------------------------------------------+ + +LMM_RESET +~~~~~~~~~ + +message_id: 0x5 +protocol_id: 0x80 +This command is mandatory. + ++------------------+-----------------------------------------------------------+ +|Parameters | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|uint32 lmid |ID of the Logical Machine | ++------------------+-----------------------------------------------------------+ +|uint32 flags |Reset flags: | +| |Bits[31:1] Reserved, must be zero. | +| |Bit[0] Graceful request: | +| |Set to 1 if the request is a graceful request. | +| |Set to 0 if the request is a forceful request. | ++------------------+-----------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status |SUCCESS: The LMM RESET command finished successfully in | +| |graceful reset or LM successfully resets in forceful reset.| +| |NOT_FOUND: if lmId not points to a valid logical machine. | +| |INVALID_PARAMETERS: if lmId is same as the caller. | +| |DENIED: if the agent does not have permission to manage the| +| |the LM specified by lmid. | ++------------------+-----------------------------------------------------------+ + +LMM_SHUTDOWN +~~~~~~~~~~~~ + +message_id: 0x6 +protocol_id: 0x80 +This command is mandatory. + ++------------------+-----------------------------------------------------------+ +|Parameters | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|uint32 lmid |ID of the Logical Machine | ++------------------+-----------------------------------------------------------+ +|uint32 flags |Reset flags: | +| |Bits[31:1] Reserved, must be zero. | +| |Bit[0] Graceful request: | +| |Set to 1 if the request is a graceful request. | +| |Set to 0 if the request is a forceful request. | ++------------------+-----------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status |SUCCESS: The LMM shutdown command finished successfully in | +| |graceful request or LM successfully shutdown in forceful | +| |request. | +| |NOT_FOUND: if lmId not points to a valid logical machine. | +| |INVALID_PARAMETERS: if lmId is same as the caller. | +| |DENIED: if the agent does not have permission to manage the| +| |the LM specified by lmid. | ++------------------+-----------------------------------------------------------+ + +LMM_WAKE +~~~~~~~~ + +message_id: 0x7 +protocol_id: 0x80 +This command is mandatory. + ++------------------+-----------------------------------------------------------+ +|Parameters | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|uint32 lmid |ID of the Logical Machine | ++------------------+-----------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status |SUCCESS: if LM wake command successfully returns. | +| |NOT_FOUND: if lmId not points to a valid logical machine. | +| |INVALID_PARAMETERS: if lmId is same as the caller. | +| |DENIED: if the agent does not have permission to manage the| +| |the LM specified by lmid. | ++------------------+-----------------------------------------------------------+ + +LMM_SUSPEND +~~~~~~~~~~~ + +message_id: 0x8 +protocol_id: 0x80 +This command is mandatory. + ++------------------+-----------------------------------------------------------+ +|Parameters | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|uint32 lmid |ID of the Logical Machine | ++------------------+-----------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status |SUCCESS: if LM suspend command successfully returns. | +| |NOT_FOUND: if lmId not points to a valid logical machine. | +| |INVALID_PARAMETERS: if lmId is same as the caller. | +| |DENIED: if the agent does not have permission to manage the| +| |the LM specified by lmid. | ++------------------+-----------------------------------------------------------+ + +LMM_NOTIFY +~~~~~~~~~~ + +message_id: 0x9 +protocol_id: 0x80 +This command is mandatory. + ++------------------+-----------------------------------------------------------+ +|Parameters | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|uint32 lmid |ID of the Logical Machine | ++------------------+-----------------------------------------------------------+ +|uint32 flags |Notification flags: | +| |Bits[31:3] Reserved, must be zero. | +| |Bit[3] Wake (resume) notification: | +| |Set to 1 to send notification. | +| |Set to 0 if no notification. | +| |Bit[2] Suspend (sleep) notification: | +| |Set to 1 to send notification. | +| |Set to 0 if no notification. | +| |Bit[1] Shutdown (off) notification: | +| |Set to 1 to send notification. | +| |Set to 0 if no notification. | +| |Bit[0] Boot (on) notification: | +| |Set to 1 to send notification. | +| |Set to 0 if no notification | ++------------------+-----------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status |SUCCESS: if the notification state successfully updated. | +| |NOT_FOUND: if lmId not points to a valid logical machine. | +| |INVALID_PARAMETERS: if input attributes flag specifies | +| |unsupported or invalid configurations. | +| |DENIED: if the agent does not have permission to request | +| |the notification. | ++------------------+-----------------------------------------------------------+ + +LMM_RESET_REASON +~~~~~~~~~~~~~~~~ + +message_id: 0xA +protocol_id: 0x80 +This command is mandatory. + +This command is to return the reset reason that caused the last reset, such as +POR, WDOG, JTAG and etc. + ++---------------------+--------------------------------------------------------+ +|Parameters | ++---------------------+--------------------------------------------------------+ +|Name |Description | ++---------------------+--------------------------------------------------------+ +|uint32 lmid |ID of the Logical Machine | ++---------------------+--------------------------------------------------------+ +|Return values | ++---------------------+--------------------------------------------------------+ +|Name |Description | ++---------------------+--------------------------------------------------------+ +|int32 status |SUCCESS: if the reset reason of the LM successfully | +| |updated. | +| |NOT_FOUND: if lmId not points to a valid logical machine| +| |DENIED: if the agent does not have permission to request| +| |the reset reason. | ++---------------------+--------------------------------------------------------+ +|uint32 bootflags |Boot reason flags. This parameter has the format: | +| |Bits[31] Valid. | +| |Set to 1 if the entire reason is valid. | +| |Set to 0 if the entire reason is not valid. | +| |Bits[30:29] Reserved, must be zero. | +| |Bit[28] Valid origin: | +| |Set to 1 if the origin field is valid. | +| |Set to 0 if the origin field is not valid. | +| |Bits[27:24] Origin. | +| |Logical Machine(LM) ID that causes the BOOT of this LM | +| |Bit[23] Valid err ID: | +| |Set to 1 if the error ID field is valid. | +| |Set to 0 if the error ID field is not valid. | +| |Bits[22:8] Error ID(Agent ID of the system). | +| |Bit[7:0] Reason(WDOG, POR, FCCU and etc) | ++---------------------+--------------------------------------------------------+ +|uint32 shutdownflags |Shutdown reason flags. This parameter has the format: | +| |Bits[31] Valid. | +| |Set to 1 if the entire reason is valid. | +| |Set to 0 if the entire reason is not valid. | +| |Bits[30:29] Number of valid extended info words. | +| |Bit[28] Valid origin: | +| |Set to 1 if the origin field is valid. | +| |Set to 0 if the origin field is not valid. | +| |Bits[27:24] Origin. | +| |Logical Machine(LM) ID that causes the BOOT of this LM | +| |Bit[23] Valid err ID: | +| |Set to 1 if the error ID field is valid. | +| |Set to 0 if the error ID field is not valid. | +| |Bits[22:8] Error ID(Agent ID of the System). | +| |Bit[7:0] Reason | ++---------------------+--------------------------------------------------------+ +|uint32 extinfo[3] |Array of extended info words(e.g. fault pc) | ++---------------------+--------------------------------------------------------+ + +LMM_POWER_ON +~~~~~~~~~~~~ + +message_id: 0xB +protocol_id: 0x80 +This command is mandatory. + ++------------------+-----------------------------------------------------------+ +|Parameters | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|uint32 lmid |ID of the Logical Machine | ++------------------+-----------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status |SUCCESS: if LM successfully powers on. | +| |NOT_FOUND: if lmId not points to a valid logical machine. | +| |INVALID_PARAMETERS: if lmId is same as the caller. | +| |DENIED: if the agent does not have permission to manage the| +| |the LM specified by lmid. | ++------------------+-----------------------------------------------------------+ + +LMM_RESET_VECTOR_SET +~~~~~~~~~~~~~~~~~~~~ + +message_id: 0xC +protocol_id: 0x80 +This command is mandatory. + ++-----------------------+------------------------------------------------------+ +|Parameters | ++-----------------------+------------------------------------------------------+ +|Name |Description | ++-----------------------+------------------------------------------------------+ +|uint32 lmid |ID of the Logical Machine | ++-----------------------+------------------------------------------------------+ +|uint32 cpuid |ID of the CPU inside the LM | ++-----------------------+------------------------------------------------------+ +|uint32 flags |Reset vector flags | +| |Bits[31:0] Reserved, must be zero. | ++-----------------------+------------------------------------------------------+ +|uint32 resetVectorLow |Lower vector | ++-----------------------+------------------------------------------------------+ +|uint32 resetVectorHigh |Higher vector | ++-----------------------+------------------------------------------------------+ +|Return values | ++-----------------------+------------------------------------------------------+ +|Name |Description | ++-----------------------+------------------------------------------------------+ +|int32 status |SUCCESS: If reset vector is set successfully. | +| |NOT_FOUND: if lmId not points to a valid logical | +| |machine, or cpuId is not valid. | +| |INVALID_PARAMETERS: if reset vector is invalid. | +| |DENIED: if the agent does not have permission to set | +| |the reset vector for the CPU in the LM. | ++-----------------------+------------------------------------------------------+ + +NEGOTIATE_PROTOCOL_VERSION +~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +message_id: 0x10 +protocol_id: 0x80 +This command is mandatory. + ++--------------------+---------------------------------------------------------+ +|Parameters | ++--------------------+---------------------------------------------------------+ +|Name |Description | ++--------------------+---------------------------------------------------------+ +|uint32 version |The negotiated protocol version the agent intends to use | ++--------------------+---------------------------------------------------------+ +|Return values | ++--------------------+---------------------------------------------------------+ +|Name |Description | ++--------------------+---------------------------------------------------------+ +|int32 status |SUCCESS: if the negotiated protocol version is supported | +| |by the platform. All commands, responses, and | +| |notifications post successful return of this command must| +| |comply with the negotiated version. | +| |NOT_SUPPORTED: if the protocol version is not supported. | ++--------------------+---------------------------------------------------------+ + +Notifications +_____________ + +LMM_EVENT +~~~~~~~~~ + +message_id: 0x0 +protocol_id: 0x80 + ++------------------+-----------------------------------------------------------+ +|Parameters | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|uint32 lmid |Identifier for the LM that caused the transition. | ++------------------+-----------------------------------------------------------+ +|uint32 eventlm |Identifier of the LM this event refers to. | ++------------------+-----------------------------------------------------------+ +|uint32 flags |LM events: | +| |Bits[31:3] Reserved, must be zero. | +| |Bit[3] Wake (resume) event: | +| |1 LM has awakened. | +| |0 not a wake event. | +| |Bit[2] Suspend (sleep) event: | +| |1 LM has suspended. | +| |0 not a suspend event. | +| |Bit[1] Shutdown (off) event: | +| |1 LM has shutdown. | +| |0 not a shutdown event. | +| |Bit[0] Boot (on) event: | +| |1 LM has booted. | +| |0 not a boot event. | ++------------------+-----------------------------------------------------------+ + SCMI_BBM: System Control and Management BBM Vendor Protocol ============================================================== @@ -436,6 +931,312 @@ protocol_id: 0x81 | |0 no button change detected. | +------------------+-----------------------------------------------------------+ +SCMI_CPU: System Control and Management CPU Vendor Protocol +============================================================== + +This protocol allows an agent to start or stop a CPU. It is used to manage +auxiliary CPUs in an LM (e.g. additional cores in an AP cluster or +Cortex-M cores). +Note: + - For cores in AP cluster, PSCI should be used and ATF will use CPU + protocol to handle them. For cores in non-AP cluster, Operating System(e.g. + Linux OS) could use CPU protocols to control Cortex-M7 cores. + - CPU indicates the core and its auxiliary peripherals(e.g. TCM) inside + i.MX SoC + +The CPU protocol provides functions to: + +- Describe the protocol version. +- Discover implementation attributes. +- Discover the CPUs defined in the system. +- Start a CPU. +- Stop a CPU. +- Set the boot and resume addresses for a CPU. +- Set the sleep mode of a CPU. +- Configure wake-up sources for a CPU. +- Configure power domain reactions (LPM mode and retention mask) for a CPU. +- The CPU IDs can be found in the CPU section of the SoC DEVICE: SM Device + Interface. They can also be found in the SoC RM. See the CPU Mode Control + (CMC) list in General Power Controller (GPC) section. + +CPU settings are not aggregated and setting their state is normally exclusive +to one client. + +Commands: +_________ + +PROTOCOL_VERSION +~~~~~~~~~~~~~~~~ + +message_id: 0x0 +protocol_id: 0x82 +This command is mandatory. + ++---------------+--------------------------------------------------------------+ +|Return values | ++---------------+--------------------------------------------------------------+ +|Name |Description | ++---------------+--------------------------------------------------------------+ +|int32 status | See ARM SCMI Specification for status code definitions. | ++---------------+--------------------------------------------------------------+ +|uint32 version | For this revision of the specification, this value must be | +| | 0x10000. | ++---------------+--------------------------------------------------------------+ + +PROTOCOL_ATTRIBUTES +~~~~~~~~~~~~~~~~~~~ + +message_id: 0x1 +protocol_id: 0x82 +This command is mandatory. + ++---------------+--------------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status | See ARM SCMI Specification for status code definitions. | ++------------------+-----------------------------------------------------------+ +|uint32 attributes |Protocol attributes: | +| |Bits[31:16] Reserved, must be zero. | +| |Bits[15:0] Number of CPUs | ++------------------+-----------------------------------------------------------+ + +PROTOCOL_MESSAGE_ATTRIBUTES +~~~~~~~~~~~~~~~~~~~~~~~~~~~ + +message_id: 0x2 +protocol_id: 0x82 +This command is mandatory. + ++---------------+--------------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status |SUCCESS: in case the message is implemented and available | +| |to use. | +| |NOT_FOUND: if the message identified by message_id is | +| |invalid or not implemented | ++------------------+-----------------------------------------------------------+ +|uint32 attributes |Flags that are associated with a specific function in the | +| |protocol. For all functions in this protocol, this | +| |parameter has a value of 0 | ++------------------+-----------------------------------------------------------+ + +CPU_ATTRIBUTES +~~~~~~~~~~~~~~ + +message_id: 0x4 +protocol_id: 0x82 +This command is mandatory. + ++------------------+-----------------------------------------------------------+ +|Parameters | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|uint32 cpuid |Identifier for the CPU | ++------------------+-----------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status |SUCCESS: if valid attributes are returned successfully. | +| |NOT_FOUND: if the cpuid is not valid. | ++------------------+-----------------------------------------------------------+ +|uint32 attributes |Bits[31:0] Reserved, must be zero | ++------------------+-----------------------------------------------------------+ +|char name[16] |NULL terminated ASCII string with CPU name up to 16 bytes | ++------------------+-----------------------------------------------------------+ + +CPU_START +~~~~~~~~~ + +message_id: 0x4 +protocol_id: 0x82 +This command is mandatory. + ++------------------+-----------------------------------------------------------+ +|Parameters | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|uint32 cpuid |Identifier for the CPU | ++------------------+-----------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status |SUCCESS: if the cpu is started successfully. | +| |NOT_FOUND: if cpuid is not valid. | +| |DENIED: the calling agent is not allowed to start this CPU.| ++------------------+-----------------------------------------------------------+ + +CPU_STOP +~~~~~~~~ + +message_id: 0x5 +protocol_id: 0x82 +This command is mandatory. + ++------------------+-----------------------------------------------------------+ +|Parameters | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|uint32 cpuid |Identifier for the CPU | ++------------------+-----------------------------------------------------------+ +|Return values | ++------------------+-----------------------------------------------------------+ +|Name |Description | ++------------------+-----------------------------------------------------------+ +|int32 status |SUCCESS: if the cpu is started successfully. | +| |NOT_FOUND: if cpuid is not valid. | +| |DENIED: the calling agent is not allowed to stop this CPU. | ++------------------+-----------------------------------------------------------+ + +CPU_RESET_VECTOR_SET +~~~~~~~~~~~~~~~~~~~~ + +message_id: 0x6 +protocol_id: 0x82 +This command is mandatory. + ++----------------------+-------------------------------------------------------+ +|Parameters | ++----------------------+-------------------------------------------------------+ +|Name |Description | ++----------------------+-------------------------------------------------------+ +|uint32 cpuid |Identifier for the CPU | ++----------------------+-------------------------------------------------------+ +|uint32 flags |Reset vector flags: | +| |Bit[31] Resume flag. | +| |Set to 1 to update the reset vector used on resume. | +| |Bit[30] Boot flag. | +| |Set to 1 to update the reset vector used for boot. | +| |Bits[29:1] Reserved, must be zero. | +| |Bit[0] Table flag. | +| |Set to 1 if vector is the vector table base address. | ++----------------------+-------------------------------------------------------+ +|uint32 resetVectorLow |Lower vector: | +| |If bit[0] of flags is 0, the lower 32 bits of the | +| |physical address where the CPU should execute from on | +| |reset. If bit[0] of flags is 1, the lower 32 bits of | +| |the vector table base address | ++----------------------+-------------------------------------------------------+ +|uint32 resetVectorhigh|Upper vector: | +| |If bit[0] of flags is 0, the upper 32 bits of the | +| |physical address where the CPU should execute from on | +| |reset. If bit[0] of flags is 1, the upper 32 bits of | +| |the vector table base address | ++----------------------+-------------------------------------------------------+ +|Return values | ++----------------------+-------------------------------------------------------+ +|Name |Description | ++----------------------+-------------------------------------------------------+ +|int32 status |SUCCESS: if the CPU reset vector is set successfully. | +| |NOT_FOUND: if cpuId does not point to a valid CPU. | +| |INVALID_PARAMETERS: the requested vector type is not | +| |supported by this CPU. | +| |DENIED: the calling agent is not allowed to set the | +| |reset vector of this CPU | ++----------------------+-------------------------------------------------------+ + +CPU_SLEEP_MODE_SET +~~~~~~~~~~~~~~~~~~ + +message_id: 0x7 +protocol_id: 0x82 +This command is mandatory. + ++----------------------+-------------------------------------------------------+ +|Parameters | ++----------------------+-------------------------------------------------------+ +|Name |Description | ++----------------------+-------------------------------------------------------+ +|uint32 cpuid |Identifier for the CPU | ++----------------------+-------------------------------------------------------+ +|uint32 flags |Sleep mode flags: | +| |Bits[31:1] Reserved, must be zero. | +| |Bit[0] IRQ mux: | +| |If set to 1 the wakeup mux source is the GIC, else if 0| +| |then the GPC | ++----------------------+-------------------------------------------------------+ +|uint32 sleepmode |target sleep mode. When CPU runs into WFI, the GPC mode| +| |will be triggered to be in below modes: | +| |RUN(0), WAIT(1), STOP(2), SUSPEND(3) | ++----------------------+-------------------------------------------------------+ +|Return values | ++----------------------+-------------------------------------------------------+ +|Name |Description | ++----------------------+-------------------------------------------------------+ +|int32 status |SUCCESS: if the CPU sleep mode is set successfully. | +| |NOT_FOUND: if cpuId does not point to a valid CPU. | +| |INVALID_PARAMETERS: the sleepmode or flags is invalid. | +| |DENIED: the calling agent is not allowed to configure | +| |the CPU | ++----------------------+-------------------------------------------------------+ + +CPU_INFO_GET +~~~~~~~~~~~~ + +message_id: 0xC +protocol_id: 0x82 +This command is mandatory. + ++----------------------+-------------------------------------------------------+ +|Parameters | ++----------------------+-------------------------------------------------------+ +|Name |Description | ++----------------------+-------------------------------------------------------+ +|uint32 cpuid |Identifier for the CPU | ++----------------------+-------------------------------------------------------+ +|Return values | ++----------------------+-------------------------------------------------------+ +|Name |Description | ++----------------------+-------------------------------------------------------+ +|int32 status |SUCCESS: if valid attributes are returned successfully.| +| |NOT_FOUND: if the cpuid is not valid. | ++----------------------+-------------------------------------------------------+ +|uint32 runmode |Run mode for the CPU | +| |RUN(0):cpu started | +| |HOLD(1):cpu powered up and reset asserted | +| |STOP(2):cpu reseted and hold cpu | +| |SUSPEND(3):in cpuidle state | ++----------------------+-------------------------------------------------------+ +|uint32 sleepmode |Sleep mode for the CPU, see CPU_SLEEP_MODE_SET | ++----------------------+-------------------------------------------------------+ +|uint32 resetvectorlow |Reset vector low 32 bits for the CPU | ++----------------------+-------------------------------------------------------+ +|uint32 resetvecothigh |Reset vector high 32 bits for the CPU | ++----------------------+-------------------------------------------------------+ + +NEGOTIATE_PROTOCOL_VERSION +~~~~~~~~~~~~~~~~~~~~~~~~~~ + +message_id: 0x10 +protocol_id: 0x82 +This command is mandatory. + ++--------------------+---------------------------------------------------------+ +|Parameters | ++--------------------+---------------------------------------------------------+ +|Name |Description | ++--------------------+---------------------------------------------------------+ +|uint32 version |The negotiated protocol version the agent intends to use | ++--------------------+---------------------------------------------------------+ +|Return values | ++--------------------+---------------------------------------------------------+ +|Name |Description | ++--------------------+---------------------------------------------------------+ +|int32 status |SUCCESS: if the negotiated protocol version is supported | +| |by the platform. All commands, responses, and | +| |notifications post successful return of this command must| +| |comply with the negotiated version. | +| |NOT_SUPPORTED: if the protocol version is not supported. | ++--------------------+---------------------------------------------------------+ + SCMI_MISC: System Control and Management MISC Vendor Protocol ================================================================ -- 2.37.1
