Ethernet boot requires CPSW nodes to be present starting from R5 SPL stage. Add bootph-all property to required nodes to enable Ethernet boot on AM68-SK and J721S2-EVM. Signed-off-by: Chintan Vankar <c-vankar@xxxxxx> --- Link to v1: https://lore.kernel.org/r/20250106123122.3531845-2-c-vankar@xxxxxx/ Changes from v1 to v2: - No changes. arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts | 3 +++ arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi | 4 ++++ 2 files changed, 7 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts index 11522b36e0ce..8e9101dd2152 100644 --- a/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts +++ b/arch/arm64/boot/dts/ti/k3-am68-sk-base-board.dts @@ -333,6 +333,7 @@ J721S2_WKUP_IOPAD(0x008, PIN_OUTPUT, 0) /* (E22) MCU_RGMII1_TD3 */ J721S2_WKUP_IOPAD(0x018, PIN_OUTPUT, 0) /* (F21) MCU_RGMII1_TXC */ J721S2_WKUP_IOPAD(0x000, PIN_OUTPUT, 0) /* (F22) MCU_RGMII1_TX_CTL */ >; + bootph-all; }; mcu_mdio_pins_default: mcu-mdio-default-pins { @@ -340,6 +341,7 @@ mcu_mdio_pins_default: mcu-mdio-default-pins { J721S2_WKUP_IOPAD(0x034, PIN_OUTPUT, 0) /* (A21) MCU_MDIO0_MDC */ J721S2_WKUP_IOPAD(0x030, PIN_INPUT, 0) /* (A22) MCU_MDIO0_MDIO */ >; + bootph-all; }; mcu_mcan0_pins_default: mcu-mcan0-default-pins { @@ -615,6 +617,7 @@ &mcu_cpsw { &davinci_mdio { phy0: ethernet-phy@0 { reg = <0>; + bootph-all; ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; ti,min-output-impedance; diff --git a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi index bc31266126d0..29cd4b1ffbbf 100644 --- a/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi +++ b/arch/arm64/boot/dts/ti/k3-j721s2-mcu-wakeup.dtsi @@ -154,12 +154,14 @@ mcu_conf: bus@40f00000 { cpsw_mac_syscon: ethernet-mac-syscon@200 { compatible = "ti,am62p-cpsw-mac-efuse", "syscon"; reg = <0x200 0x8>; + bootph-all; }; phy_gmii_sel: phy@4040 { compatible = "ti,am654-phy-gmii-sel"; reg = <0x4040 0x4>; #phy-cells = <1>; + bootph-all; }; }; @@ -538,6 +540,7 @@ mcu_cpsw: ethernet@46000000 { clocks = <&k3_clks 29 28>; clock-names = "fck"; power-domains = <&k3_pds 29 TI_SCI_PD_EXCLUSIVE>; + bootph-all; dmas = <&mcu_udmap 0xf000>, <&mcu_udmap 0xf001>, @@ -562,6 +565,7 @@ cpsw_port1: port@1 { label = "port1"; ti,syscon-efuse = <&cpsw_mac_syscon 0x0>; phys = <&phy_gmii_sel 1>; + bootph-all; }; }; -- 2.34.1
