The bootph-all and bootph-pre-ram tags were introduced in dt-schema
(dtschema/schemas/bootph.yaml) to define node usage across different
boot phases.
Add boot phase tags to all required nodes to ensure boot support from
all sources, including UART, Ethernet, uSD card, eMMC, and OSPI NOR Flash.
Signed-off-by: Wadim Egorov <w.egorov@xxxxxxxxx>
---
arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi | 12 ++++++++++++
.../boot/dts/ti/k3-am642-phyboard-electra-rdk.dts | 5 +++++
2 files changed, 17 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
index 99a6fdfaa7fb..52d53b690ac9 100644
--- a/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am64-phycore-som.dtsi
@@ -27,6 +27,7 @@ aliases {
memory@80000000 {
device_type = "memory";
reg = <0x00000000 0x80000000 0x00000000 0x80000000>;
+ bootph-all;
};
reserved_memory: reserved-memory {
@@ -132,6 +133,7 @@ AM64X_IOPAD(0x01f8, PIN_INPUT, 4) /* (P5) PRG0_PRU1_GPO18.MDIO0_MDIO */
AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4) /* (R2) PRG0_PRU1_GPO19.MDIO0_MDC */
AM64X_IOPAD(0x0100, PIN_OUTPUT, 7) /* (V7) PRG1_PRU0_GPO18.GPIO0_63 */
>;
+ bootph-all;
};
cpsw_rgmii1_pins_default: cpsw-rgmii1-default-pins {
@@ -150,6 +152,7 @@ AM64X_IOPAD(0x01f4, PIN_INPUT, 4) /* (V5) PRG0_PRU1_GPO17.RGMII1_RD3 */
AM64X_IOPAD(0x014c, PIN_OUTPUT, 4) /* (AA14) PRG1_PRU1_GPO17.RGMII1_TD3 */
AM64X_IOPAD(0x0154, PIN_INPUT, 7) /* (V12) PRG1_PRU1_GPO19.GPIO0_84 */
>;
+ bootph-all;
};
eeprom_wp_pins_default: eeprom-wp-default-pins {
@@ -169,6 +172,7 @@ main_i2c0_pins_default: main-i2c0-default-pins {
AM64X_IOPAD(0x0260, PIN_INPUT, 0) /* (A18) I2C0_SCL */
AM64X_IOPAD(0x0264, PIN_INPUT, 0) /* (B18) I2C0_SDA */
>;
+ bootph-all;
};
ospi0_pins_default: ospi0-default-pins {
@@ -185,6 +189,7 @@ AM64X_IOPAD(0x0024, PIN_INPUT, 0) /* (N18) OSPI0_D6 */
AM64X_IOPAD(0x0028, PIN_INPUT, 0) /* (M17) OSPI0_D7 */
AM64X_IOPAD(0x002c, PIN_OUTPUT, 0) /* (L19) OSPI0_CSn0 */
>;
+ bootph-all;
};
rtc_pins_default: rtc-defaults-pins {
@@ -197,6 +202,7 @@ AM64X_IOPAD(0x0278, PIN_INPUT, 7) /* (C19) EXTINTn.GPIO1_70 */
&cpsw3g {
pinctrl-names = "default";
pinctrl-0 = <&cpsw_rgmii1_pins_default>;
+ bootph-all;
status = "okay";
};
@@ -204,6 +210,7 @@ &cpsw3g_mdio {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&cpsw_mdio_pins_default>;
+ bootph-all;
cpsw3g_phy1: ethernet-phy@1 {
compatible = "ethernet-phy-id2000.a231", "ethernet-phy-ieee802.3-c22";
@@ -215,12 +222,14 @@ cpsw3g_phy1: ethernet-phy@1 {
reset-gpios = <&main_gpio0 63 GPIO_ACTIVE_LOW>;
reset-assert-us = <1000>;
reset-deassert-us = <1000>;
+ bootph-all;
};
};
&cpsw_port1 {
phy-mode = "rgmii-rxid";
phy-handle = <&cpsw3g_phy1>;
+ bootph-all;
status = "okay";
};
@@ -266,6 +275,7 @@ &main_i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&main_i2c0_pins_default>;
clock-frequency = <400000>;
+ bootph-all;
eeprom@50 {
compatible = "atmel,24c32";
@@ -377,6 +387,7 @@ serial_flash: flash@0 {
cdns,tchsh-ns = <60>;
cdns,tslch-ns = <60>;
cdns,read-delay = <0>;
+ bootph-all;
};
};
@@ -386,6 +397,7 @@ &sdhci0 {
ti,driver-strength-ohm = <50>;
disable-wp;
keep-power-in-suspend;
+ bootph-all;
};
&tscadc0 {
diff --git a/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts
index bc8e1ce11047..6fbd8d932396 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-phyboard-electra-rdk.dts
@@ -171,6 +171,7 @@ vcc_3v3_mmc: regulator-sd {
regulator-max-microvolt = <3300000>;
regulator-boot-on;
regulator-always-on;
+ bootph-all;
};
};
@@ -275,6 +276,7 @@ AM64X_IOPAD(0x0290, PIN_INPUT, 0) /* MMC1_CLKLB */
AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0) /* (J19) MMC1_CMD */
AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0) /* (D19) MMC1_SDCD */
>;
+ bootph-all;
};
main_spi0_pins_default: main-spi0-default-pins {
@@ -291,6 +293,7 @@ main_uart0_pins_default: main-uart0-default-pins {
AM64X_IOPAD(0x0230, PIN_INPUT, 0) /* (D15) UART0_RXD */
AM64X_IOPAD(0x0234, PIN_OUTPUT, 0) /* (C16) UART0_TXD */
>;
+ bootph-all;
};
main_uart1_pins_default: main-uart1-default-pins {
@@ -413,6 +416,7 @@ &main_uart0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&main_uart0_pins_default>;
+ bootph-all;
};
&main_uart1 {
@@ -429,6 +433,7 @@ &sdhci1 {
pinctrl-0 = <&main_mmc1_pins_default>;
disable-wp;
no-1-8-v;
+ bootph-all;
};
&serdes0 {
--
2.34.1
