Copy tsens node from ap8064 and adjust some values
Co-developed-by: wctrl <wctrl@xxxxxxxxx>
Signed-off-by: wctrl <wctrl@xxxxxxxxx>
Signed-off-by: Rudraksha Gupta <guptarud@xxxxxxxxx>
---
arch/arm/boot/dts/qcom/qcom-msm8960.dtsi | 59 +++++++++++++++++++++++++++++++-
1 file changed, 58 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
index 865fe7cc39511d7cb9ec5c4b12100404f77e2989..155d6aba61e390dabca6b72160543b5aa134b219 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8960.dtsi
@@ -52,6 +52,36 @@ memory@80000000 {
reg = <0x80000000 0>;
};
+ thermal-zones {
+ cpu0-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&tsens 0>;
+
+ trips {
+ cpu_alert0: trip0 {
+ temperature = <60000>;
+ hysteresis = <10000>;
+ type = "passive";
+ };
+ };
+ };
+
+ cpu1-thermal {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+ thermal-sensors = <&tsens 1>;
+
+ trips {
+ cpu_alert1: trip0 {
+ temperature = <60000>;
+ hysteresis = <10000>;
+ type = "passive";
+ };
+ };
+ };
+ };
+
cpu-pmu {
compatible = "qcom,krait-pmu";
interrupts = <GIC_PPI 10 0x304>;
@@ -115,6 +145,21 @@ timer@200a000 {
cpu-offset = <0x80000>;
};
+ qfprom: efuse@700000 {
+ compatible = "qcom,msm8960-qfprom", "qcom,qfprom";
+ reg = <0x00700000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ tsens_calib: calib@404 {
+ reg = <0x404 0x10>;
+ };
+
+ tsens_backup: backup-calib@414 {
+ reg = <0x414 0x10>;
+ };
+ };
+
msmgpio: pinctrl@800000 {
compatible = "qcom,msm8960-pinctrl";
gpio-controller;
@@ -127,7 +172,7 @@ msmgpio: pinctrl@800000 {
};
gcc: clock-controller@900000 {
- compatible = "qcom,gcc-msm8960";
+ compatible = "qcom,gcc-msm8960", "syscon";
#clock-cells = <1>;
#reset-cells = <1>;
reg = <0x900000 0x4000>;
@@ -135,6 +180,18 @@ gcc: clock-controller@900000 {
<&pxo_board>,
<&lcc PLL4>;
clock-names = "cxo", "pxo", "pll4";
+
+ tsens: thermal-sensor {
+ compatible = "qcom,msm8960-tsens";
+
+ nvmem-cells = <&tsens_calib>, <&tsens_backup>;
+ nvmem-cell-names = "calib", "calib_backup";
+ interrupts = <GIC_SPI 178 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "uplow";
+
+ #qcom,sensors = <5>;
+ #thermal-sensor-cells = <1>;
+ };
};
lcc: clock-controller@28000000 {
--
2.45.2
