On Sun, Feb 23, 2025 at 02:22:26PM +0200, Ivaylo Ivanov wrote:
> The Exynos2200 SoC reuses the Synopsis eUSB2 PHY IP, alongside an
> external repeater, for USB 2.0. Add support for it to the existing
> driver.
>
> Signed-off-by: Ivaylo Ivanov <ivo.ivanov.ivanov1@xxxxxxxxx>
> ---
> drivers/phy/Kconfig | 2 +-
> drivers/phy/phy-snps-eusb2.c | 172 +++++++++++++++++++++++++++++++++++
> 2 files changed, 173 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig
> index 11c166204..58c911e1b 100644
> --- a/drivers/phy/Kconfig
> +++ b/drivers/phy/Kconfig
> @@ -45,7 +45,7 @@ config PHY_PISTACHIO_USB
>
> config PHY_SNPS_EUSB2
> tristate "SNPS eUSB2 PHY Driver"
> - depends on OF && (ARCH_QCOM || COMPILE_TEST)
> + depends on OF && (ARCH_EXYNOS || ARCH_QCOM || COMPILE_TEST)
> select GENERIC_PHY
> help
> Enable support for the USB high-speed SNPS eUSB2 phy on select
> diff --git a/drivers/phy/phy-snps-eusb2.c b/drivers/phy/phy-snps-eusb2.c
> index 7a242fe32..67a19d671 100644
> --- a/drivers/phy/phy-snps-eusb2.c
> +++ b/drivers/phy/phy-snps-eusb2.c
> @@ -13,6 +13,39 @@
> #include <linux/regulator/consumer.h>
> #include <linux/reset.h>
>
> +#define EXYNOS_USB_PHY_HS_PHY_CTRL_RST (0x0)
> +#define USB_PHY_RST_MASK GENMASK(1, 0)
> +#define UTMI_PORT_RST_MASK GENMASK(5, 4)
> +
> +#define EXYNOS_USB_PHY_HS_PHY_CTRL_COMMON (0x4)
> +#define RPTR_MODE BIT(10)
> +#define FSEL_20_MHZ_VAL (0x1)
> +#define FSEL_24_MHZ_VAL (0x2)
> +#define FSEL_26_MHZ_VAL (0x3)
> +#define FSEL_48_MHZ_VAL (0x2)
> +
> +#define EXYNOS_USB_PHY_CFG_PLLCFG0 (0x8)
> +#define PHY_CFG_PLL_FB_DIV_19_8_MASK GENMASK(19, 8)
> +#define DIV_19_8_19_2_MHZ_VAL (0x170)
> +#define DIV_19_8_20_MHZ_VAL (0x160)
> +#define DIV_19_8_24_MHZ_VAL (0x120)
> +#define DIV_19_8_26_MHZ_VAL (0x107)
> +#define DIV_19_8_48_MHZ_VAL (0x120)
> +
> +#define EXYNOS_USB_PHY_CFG_PLLCFG1 (0xc)
> +#define EXYNOS_PHY_CFG_PLL_FB_DIV_11_8_MASK GENMASK(11, 8)
> +#define EXYNOS_DIV_11_8_19_2_MHZ_VAL (0x0)
> +#define EXYNOS_DIV_11_8_20_MHZ_VAL (0x0)
> +#define EXYNOS_DIV_11_8_24_MHZ_VAL (0x0)
> +#define EXYNOS_DIV_11_8_26_MHZ_VAL (0x0)
> +#define EXYNOS_DIV_11_8_48_MHZ_VAL (0x1)
> +
> +#define EXYNOS_PHY_CFG_TX (0x14)
> +#define EXYNOS_PHY_CFG_TX_FSLS_VREF_TUNE_MASK GENMASK(2, 1)
> +
> +#define EXYNOS_USB_PHY_UTMI_TESTSE (0x20)
> +#define TEST_IDDQ BIT(6)
> +
> #define QCOM_USB_PHY_UTMI_CTRL0 (0x3c)
> #define SLEEPM BIT(0)
> #define OPMODE_MASK GENMASK(4, 3)
> @@ -196,6 +229,93 @@ static void qcom_eusb2_default_parameters(struct snps_eusb2_hsphy *phy)
> FIELD_PREP(PHY_CFG_TX_HS_XV_TUNE_MASK, 0x0));
> }
>
> +static int exynos_eusb2_ref_clk_init(struct snps_eusb2_hsphy *phy)
> +{
> + unsigned long ref_clk_freq = clk_get_rate(phy->ref_clk);
> +
> + switch (ref_clk_freq) {
> + case 19200000:
> + snps_eusb2_hsphy_write_mask(phy->base, EXYNOS_USB_PHY_HS_PHY_CTRL_COMMON,
> + FSEL_MASK,
> + FIELD_PREP(FSEL_MASK, FSEL_19_2_MHZ_VAL));
> +
Could you please unify the switchcase? assign the values to temp
variables, then program them from a single code stream. Or maybe even
replace switch-case with a table-based lookup.
(we probably should implement the similar change for qcom part. Maybe
you can refactor it too?)
Other than that LGTM.
> + snps_eusb2_hsphy_write_mask(phy->base, EXYNOS_USB_PHY_CFG_PLLCFG0,
> + PHY_CFG_PLL_FB_DIV_19_8_MASK,
> + FIELD_PREP(PHY_CFG_PLL_FB_DIV_19_8_MASK,
> + DIV_19_8_19_2_MHZ_VAL));
> +
> + snps_eusb2_hsphy_write_mask(phy->base, EXYNOS_USB_PHY_CFG_PLLCFG1,
> + EXYNOS_PHY_CFG_PLL_FB_DIV_11_8_MASK,
> + EXYNOS_DIV_11_8_19_2_MHZ_VAL);
> + break;
> +
> + case 20000000:
> + snps_eusb2_hsphy_write_mask(phy->base, EXYNOS_USB_PHY_HS_PHY_CTRL_COMMON,
> + FSEL_MASK,
> + FIELD_PREP(FSEL_MASK, FSEL_20_MHZ_VAL));
> +
> + snps_eusb2_hsphy_write_mask(phy->base, EXYNOS_USB_PHY_CFG_PLLCFG0,
> + PHY_CFG_PLL_FB_DIV_19_8_MASK,
> + FIELD_PREP(PHY_CFG_PLL_FB_DIV_19_8_MASK,
> + DIV_19_8_20_MHZ_VAL));
> +
> + snps_eusb2_hsphy_write_mask(phy->base, EXYNOS_USB_PHY_CFG_PLLCFG1,
> + EXYNOS_PHY_CFG_PLL_FB_DIV_11_8_MASK,
> + EXYNOS_DIV_11_8_20_MHZ_VAL);
> + break;
> +
--
With best wishes
Dmitry
