Re: [PATCH v4 1/2] arm64: dts: mediatek: mt8395-genio-1200-evk: add support for TCPC port

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, 20 Feb 2025 22:33:53 +0800, Macpaul Lin wrote:
> From: Fabien Parent <fparent@xxxxxxxxxxxx>
> 
> Enable USB Type-C support on MediaTek MT8395 Genio 1200 EVK by adding
> configuration for TCPC Port, USB-C connector, and related settings.
> 
> Configure dual role switch capability, set up PD (Power Delivery) profiles,
> and establish endpoints for SS (SuperSpeed) and HS (HighSpeed) USB.
> 
> Update pinctrl configurations for U3 P0 VBus default pins and set dr_mode
> to "otg" for OTG (On-The-Go) mode operation.
> 
> Signed-off-by: Fabien Parent <fparent@xxxxxxxxxxxx>
> Signed-off-by: Yow-Shin Liou <yow-shin.liou@xxxxxxxxxxxx>
> Signed-off-by: Simon Sun <simon.sun@xxxxxxxxxxxxxxx>
> Signed-off-by: Macpaul Lin <macpaul.lin@xxxxxxxxxxxx>
> ---
>  .../dts/mediatek/mt8395-genio-1200-evk.dts    | 72 +++++++++++++++++++
>  1 file changed, 72 insertions(+)
> 
> Changes for v2:
>  - Drop the no need '1/2' DT Schema update patch in the 1st version.
>  - Fix indent for 'ports' node, it should under the 'connector' node.
>  - Correct the index for 'port@0' and 'port@1' node.
> 
> Changes for v3:
>  - Correct the order between new added nodes.
> 
> Changes for v4:
>  - Reorder for property 'op-sink-microwatt'.
>  - Fix indentation for 'source-pdos' and 'sink-pdos' nodes.
>  - Correct node 'pin-cmd-dat' with 'pins-vbus'.
>  - Add both Highspeed and Superspeed ports to ssusb0 port.
>  - Set 'role-switch-default-mode' = "peripheral" for ssusb0 port.
>  - Rename endpoint of USB data port to 'mtu3_hs0_role_sw' and
>    'mtu3_ss0_role_sw'.
> 


My bot found new DTB warnings on the .dts files added or changed in this
series.

Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
are fixed by another series. Ultimately, it is up to the platform
maintainer whether these warnings are acceptable or not. No need to reply
unless the platform maintainer has comments.

If you already ran DT checks and didn't see these error(s), then
make sure dt-schema is up to date:

  pip3 install dtschema --upgrade


New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/mediatek/' for 20250220143354.2532448-1-macpaul.lin@xxxxxxxxxxxx:

arch/arm64/boot/dts/mediatek/mt8395-genio-1200-evk.dtb: usb@11201000: 'ports' does not match any of the regexes: '^usb@[0-9a-f]+$', 'pinctrl-[0-9]+'
	from schema $id: http://devicetree.org/schemas/usb/mediatek,mtu3.yaml#









[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux