Re: [PATCH v2 2/2] arm64: dts: rockchip: Add Radxa ROCK 4D device tree

[Detlev Casanova <detlev.casanova@xxxxxxxxxxxxx>]

Hi Jonas,

On Thursday, 13 February 2025 10:48:10 EST Jonas Karlman wrote:
> Hi Detlev,
> 
> On 2025-02-13 15:57, Detlev Casanova wrote:
> > From: Stephen Chen <stephen@xxxxxxxxx>
> > 
> > The Radxa ROCK 4D board is based on the Rockchip rk3576 SoC.
> > 
> > The device tree adds support for basic devices:
> >  - UART
> >  - SD Card
> >  - Ethernet
> >  - USB
> >  - RTC
> > 
> > It has 4 USB ports but only 3 are usable as the top left one is used
> > for maskrom.
> > 
> > It has a USB-C port that is only used for powering the board.
> > 
> > Signed-off-by: Stephen Chen <stephen@xxxxxxxxx>
> > Signed-off-by: Detlev Casanova <detlev.casanova@xxxxxxxxxxxxx>
> > ---
> > 
> >  arch/arm64/boot/dts/rockchip/Makefile         |   1 +
> >  .../boot/dts/rockchip/rk3576-rock-4d.dts      | 651 ++++++++++++++++++
> >  2 files changed, 652 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-rock-4d.dts
> > 
> > diff --git a/arch/arm64/boot/dts/rockchip/Makefile
> > b/arch/arm64/boot/dts/rockchip/Makefile index
> > def1222c1907e..a112aeb37948a 100644
> > --- a/arch/arm64/boot/dts/rockchip/Makefile
> > +++ b/arch/arm64/boot/dts/rockchip/Makefile
> > @@ -132,6 +132,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) +=
> > rk3568-wolfvision-pf5-display-vz.dtbo> 
> >  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-io-expander.dtbo
> >  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-armsom-sige5.dtb
> >  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-evb1-v10.dtb
> > 
> > +dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-rock-4d.dtb
> > 
> >  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3582-radxa-e52c.dtb
> >  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-armsom-sige7.dtb
> >  dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588-armsom-w3.dtb
> > 
> > diff --git a/arch/arm64/boot/dts/rockchip/rk3576-rock-4d.dts
> > b/arch/arm64/boot/dts/rockchip/rk3576-rock-4d.dts new file mode 100644
> > index 0000000000000..f356742f9d643
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/rockchip/rk3576-rock-4d.dts
> > @@ -0,0 +1,651 @@
> 
> [snip]
> 
> > +&gmac0 {
> > +	phy-mode = "rgmii-id";
> > +	clock_in_out = "output";
> > +
> > +	snps,reset-gpio = <&gpio2 RK_PB5 GPIO_ACTIVE_LOW>;
> > +	snps,reset-active-low;
> > +	snps,reset-delays-us = <0 20000 100000>;
> 
> The snps,reset- props are deprecated and should be changed to reset-
> props in the phy node.

Arg, second time I use deprectated props on new things. Are there plans or 
ways to make dtbs_check warn about those ?

> > +
> > +	pinctrl-names = "default";
> > +	pinctrl-0 = <&eth0m0_miim
> > +		     &eth0m0_tx_bus2
> > +		     &eth0m0_rx_bus2
> > +		     &eth0m0_rgmii_clk
> > +		     &eth0m0_rgmii_bus
> > +		     &ethm0_clk0_25m_out>;
> > +
> > +	phy-handle = <&rgmii_phy0>;
> > +	status = "okay";
> > +};
> 
> [snip]
> 
> > +&mdio0 {
> > +	rgmii_phy0: phy@1 {
> 
> Maybe ethernet-phy@1 ?

Indeed.

> > +		compatible = "ethernet-phy-ieee802.3-c22";
> > +		reg = <0x1>;
> > +		clocks = <&cru REFCLKO25M_GMAC0_OUT>;
> 
> Please add reset- props here.
> 
> Changing to use reset- props may cause issue if a RTL8211F PHY is used
> on the board. Use a ethernet-phy-id compatible or mainline U-Boot to
> ensure the Ethernet PHY can be discovered during probe.

Using downstream u-boot, with the RTL8211F PHY, linux can still detect the PHY 
and use it correctly, even with reset-* props at the PHY level.

I guess I can keep those there then, unless the issues you mention are more 
subtle than that ?


Detlev.