On Fri, Jan 31, 2025 at 06:33:56PM +0200, Laurentiu Palcu wrote:
> Add new properties for configuring FSYNC functionality and operation
> mode, as the chip can support both tunneling and pixel modes.
>
> While at it, add the maxim,max96724 compatible to the bindings since it
> was already added in the driver some time back.
I don't see that change.
>
> Signed-off-by: Laurentiu Palcu <laurentiu.palcu@xxxxxxxxxxx>
> ---
> .../bindings/media/i2c/maxim,max96712.yaml | 45 +++++++++++++++++++
> 1 file changed, 45 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max96712.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max96712.yaml
> index 26f85151afbd3..410004f3a032f 100644
> --- a/Documentation/devicetree/bindings/media/i2c/maxim,max96712.yaml
> +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max96712.yaml
> @@ -36,6 +36,48 @@ properties:
>
> enable-gpios: true
>
> + '#gpio-cells':
> + const: 2
> + description: |
Don't need '|' if no formatting.
> + First cell is the GPIO pin number, second cell is the flags. The GPIO pin
> + number must be in range of [0, 11].
> +
> + gpio-controller: true
> +
> + maxim,operation-mode:
> + description: |
> + Deserializer mode of operation: 0 - tunneling mode, 1 - pixel mode
> + $ref: /schemas/types.yaml#/definitions/uint32
> + enum: [0, 1]
> + default: 0
> +
> + maxim,fsync-config:
> + description: |
> + Frame synchronization (FSYNC) is used to align images sent from multiple
> + sources in surround-view applications and is required for concatenation.
> + In FSYNC mode, the deserializer sends a sync signal to each serializer;
> + the serializers then send the signal to the connected sensor.
> + $ref: /schemas/types.yaml#/definitions/uint32-array
> + minItems: 2
> + items:
> + - description: |
> + FSYNC mode:
> + 0 - off, no FSYNC generation
> + 1 - internal, GPIO is not used as input or output
> + 2 - master, GPIO pin is used to drive a slave deserializer
> + 3 - slave, GPIO pin is used as FSYNC input driven by a master device
> + enum: [0, 1, 2, 3]
> + default: 0
> + - description: |
> + FSYNC TX ID: GPIO ID used for transmitting FSYNC signal
> + minimum: 0
> + maximum: 31
> + default: 0
> + - description: |
> + FSYNC pin: 0 - MFP0, 1 - MFP7. Not used for internal mode.
> + enum: [0, 1]
> + default: 0
> +
> ports:
> $ref: /schemas/graph.yaml#/properties/ports
>
> @@ -92,6 +134,9 @@ examples:
> #include <dt-bindings/gpio/gpio.h>
> #include <dt-bindings/media/video-interfaces.h>
>
> + maxim,operation-mode = <0>;
> + maxim,fsync-config = <1 0>;
> +
> i2c@e6508000 {
> #address-cells = <1>;
> #size-cells = <0>;
> --
> 2.44.1
>
