The BM (Buffer Management) config controls the pause frame generated
on the PPE port. There are maximum 15 BM ports and 4 groups supported,
all BM ports are assigned to group 0 by default. The number of hardware
buffers configured for the port influence the threshold of the flow
control for that port.
Signed-off-by: Luo Jie <quic_luoj@xxxxxxxxxxx>
---
drivers/net/ethernet/qualcomm/ppe/Makefile | 2 +-
drivers/net/ethernet/qualcomm/ppe/ppe.c | 5 +
drivers/net/ethernet/qualcomm/ppe/ppe_config.c | 193 +++++++++++++++++++++++++
drivers/net/ethernet/qualcomm/ppe/ppe_config.h | 12 ++
drivers/net/ethernet/qualcomm/ppe/ppe_regs.h | 59 ++++++++
5 files changed, 270 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/qualcomm/ppe/Makefile b/drivers/net/ethernet/qualcomm/ppe/Makefile
index 63d50d3b4f2e..410a7bb54cfe 100644
--- a/drivers/net/ethernet/qualcomm/ppe/Makefile
+++ b/drivers/net/ethernet/qualcomm/ppe/Makefile
@@ -4,4 +4,4 @@
#
obj-$(CONFIG_QCOM_PPE) += qcom-ppe.o
-qcom-ppe-objs := ppe.o
+qcom-ppe-objs := ppe.o ppe_config.o
diff --git a/drivers/net/ethernet/qualcomm/ppe/ppe.c b/drivers/net/ethernet/qualcomm/ppe/ppe.c
index 4d90fcb8fa43..e8aa4eabaa7f 100644
--- a/drivers/net/ethernet/qualcomm/ppe/ppe.c
+++ b/drivers/net/ethernet/qualcomm/ppe/ppe.c
@@ -15,6 +15,7 @@
#include <linux/reset.h>
#include "ppe.h"
+#include "ppe_config.h"
#define PPE_PORT_MAX 8
#define PPE_CLK_RATE 353000000
@@ -194,6 +195,10 @@ static int qcom_ppe_probe(struct platform_device *pdev)
if (ret)
return dev_err_probe(dev, ret, "PPE clock config failed\n");
+ ret = ppe_hw_config(ppe_dev);
+ if (ret)
+ return dev_err_probe(dev, ret, "PPE HW config failed\n");
+
platform_set_drvdata(pdev, ppe_dev);
return 0;
diff --git a/drivers/net/ethernet/qualcomm/ppe/ppe_config.c b/drivers/net/ethernet/qualcomm/ppe/ppe_config.c
new file mode 100644
index 000000000000..848f65ef32ea
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/ppe/ppe_config.c
@@ -0,0 +1,193 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/* PPE HW initialization configs such as BM(buffer management),
+ * QM(queue management) and scheduler configs.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/regmap.h>
+
+#include "ppe.h"
+#include "ppe_config.h"
+#include "ppe_regs.h"
+
+/**
+ * struct ppe_bm_port_config - PPE BM port configuration.
+ * @port_id_start: The fist BM port ID to configure.
+ * @port_id_end: The last BM port ID to configure.
+ * @pre_alloc: BM port dedicated buffer number.
+ * @in_fly_buf: Buffer number for receiving the packet after pause frame sent.
+ * @ceil: Ceil to generate the back pressure.
+ * @weight: Weight value.
+ * @resume_offset: Resume offset from the threshold value.
+ * @resume_ceil: Ceil to resume from the back pressure state.
+ * @dynamic: Dynamic threshold used or not.
+ *
+ * The is for configuring the threshold that impacts the port
+ * flow control.
+ */
+struct ppe_bm_port_config {
+ unsigned int port_id_start;
+ unsigned int port_id_end;
+ unsigned int pre_alloc;
+ unsigned int in_fly_buf;
+ unsigned int ceil;
+ unsigned int weight;
+ unsigned int resume_offset;
+ unsigned int resume_ceil;
+ bool dynamic;
+};
+
+/* Assign the share buffer number 1550 to group 0 by default. */
+static int ipq9574_ppe_bm_group_config = 1550;
+
+/* The buffer configurations per PPE port. There are 15 BM ports and
+ * 4 BM groups supported by PPE. BM port (0-7) is for EDMA port 0,
+ * BM port (8-13) is for PPE physical port 1-6 and BM port 14 is for
+ * EIP port.
+ */
+static struct ppe_bm_port_config ipq9574_ppe_bm_port_config[] = {
+ {
+ /* Buffer configuration for the BM port ID 0 of EDMA. */
+ .port_id_start = 0,
+ .port_id_end = 0,
+ .pre_alloc = 0,
+ .in_fly_buf = 100,
+ .ceil = 1146,
+ .weight = 7,
+ .resume_offset = 8,
+ .resume_ceil = 0,
+ .dynamic = true,
+ },
+ {
+ /* Buffer configuration for the BM port ID 1-7 of EDMA. */
+ .port_id_start = 1,
+ .port_id_end = 7,
+ .pre_alloc = 0,
+ .in_fly_buf = 100,
+ .ceil = 250,
+ .weight = 4,
+ .resume_offset = 36,
+ .resume_ceil = 0,
+ .dynamic = true,
+ },
+ {
+ /* Buffer configuration for the BM port ID 8-13 of PPE ports. */
+ .port_id_start = 8,
+ .port_id_end = 13,
+ .pre_alloc = 0,
+ .in_fly_buf = 128,
+ .ceil = 250,
+ .weight = 4,
+ .resume_offset = 36,
+ .resume_ceil = 0,
+ .dynamic = true,
+ },
+ {
+ /* Buffer configuration for the BM port ID 14 of EIP. */
+ .port_id_start = 14,
+ .port_id_end = 14,
+ .pre_alloc = 0,
+ .in_fly_buf = 40,
+ .ceil = 250,
+ .weight = 4,
+ .resume_offset = 36,
+ .resume_ceil = 0,
+ .dynamic = true,
+ },
+};
+
+static int ppe_config_bm_threshold(struct ppe_device *ppe_dev, int bm_port_id,
+ struct ppe_bm_port_config port_cfg)
+{
+ u32 reg, val, bm_fc_val[2];
+ int ret;
+
+ /* Configure BM flow control related threshold. */
+ PPE_BM_PORT_FC_SET_WEIGHT(bm_fc_val, port_cfg.weight);
+ PPE_BM_PORT_FC_SET_RESUME_OFFSET(bm_fc_val, port_cfg.resume_offset);
+ PPE_BM_PORT_FC_SET_RESUME_THRESHOLD(bm_fc_val, port_cfg.resume_ceil);
+ PPE_BM_PORT_FC_SET_DYNAMIC(bm_fc_val, port_cfg.dynamic);
+ PPE_BM_PORT_FC_SET_REACT_LIMIT(bm_fc_val, port_cfg.in_fly_buf);
+ PPE_BM_PORT_FC_SET_PRE_ALLOC(bm_fc_val, port_cfg.pre_alloc);
+
+ /* Configure low/high bits of the ceiling for the BM port. */
+ val = FIELD_PREP(GENMASK(2, 0), port_cfg.ceil);
+ PPE_BM_PORT_FC_SET_CEILING_LOW(bm_fc_val, val);
+ val = FIELD_PREP(GENMASK(10, 3), port_cfg.ceil);
+ PPE_BM_PORT_FC_SET_CEILING_HIGH(bm_fc_val, val);
+
+ reg = PPE_BM_PORT_FC_CFG_TBL_ADDR + PPE_BM_PORT_FC_CFG_TBL_INC * bm_port_id;
+ ret = regmap_bulk_write(ppe_dev->regmap, reg,
+ bm_fc_val, ARRAY_SIZE(bm_fc_val));
+ if (ret)
+ return ret;
+
+ /* Assign the default group ID 0 to the BM port. */
+ val = FIELD_PREP(PPE_BM_PORT_GROUP_ID_SHARED_GROUP_ID, 0);
+ reg = PPE_BM_PORT_GROUP_ID_ADDR + PPE_BM_PORT_GROUP_ID_INC * bm_port_id;
+ ret = regmap_update_bits(ppe_dev->regmap, reg,
+ PPE_BM_PORT_GROUP_ID_SHARED_GROUP_ID,
+ val);
+ if (ret)
+ return ret;
+
+ /* Enable BM port flow control. */
+ val = FIELD_PREP(PPE_BM_PORT_FC_MODE_EN, true);
+ reg = PPE_BM_PORT_FC_MODE_ADDR + PPE_BM_PORT_FC_MODE_INC * bm_port_id;
+
+ return regmap_update_bits(ppe_dev->regmap, reg,
+ PPE_BM_PORT_FC_MODE_EN,
+ val);
+}
+
+/* Configure the buffer threshold for the port flow control function. */
+static int ppe_config_bm(struct ppe_device *ppe_dev)
+{
+ unsigned int i, bm_port_id, port_cfg_cnt;
+ struct ppe_bm_port_config *port_cfg;
+ u32 reg, val;
+ int ret;
+
+ /* Configure the allocated buffer number only for group 0.
+ * The buffer number of group 1-3 is already cleared to 0
+ * after PPE reset during the probe of PPE driver.
+ */
+ reg = PPE_BM_SHARED_GROUP_CFG_ADDR;
+ val = FIELD_PREP(PPE_BM_SHARED_GROUP_CFG_SHARED_LIMIT,
+ ipq9574_ppe_bm_group_config);
+ ret = regmap_update_bits(ppe_dev->regmap, reg,
+ PPE_BM_SHARED_GROUP_CFG_SHARED_LIMIT,
+ val);
+ if (ret)
+ goto bm_config_fail;
+
+ /* Configure buffer thresholds for the BM ports. */
+ port_cfg = ipq9574_ppe_bm_port_config;
+ port_cfg_cnt = ARRAY_SIZE(ipq9574_ppe_bm_port_config);
+ for (i = 0; i < port_cfg_cnt; i++) {
+ for (bm_port_id = port_cfg[i].port_id_start;
+ bm_port_id <= port_cfg[i].port_id_end; bm_port_id++) {
+ ret = ppe_config_bm_threshold(ppe_dev, bm_port_id,
+ port_cfg[i]);
+ if (ret)
+ goto bm_config_fail;
+ }
+ }
+
+ return 0;
+
+bm_config_fail:
+ dev_err(ppe_dev->dev, "PPE BM config error %d\n", ret);
+ return ret;
+}
+
+int ppe_hw_config(struct ppe_device *ppe_dev)
+{
+ return ppe_config_bm(ppe_dev);
+}
diff --git a/drivers/net/ethernet/qualcomm/ppe/ppe_config.h b/drivers/net/ethernet/qualcomm/ppe/ppe_config.h
new file mode 100644
index 000000000000..7b2f6a71cd4c
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/ppe/ppe_config.h
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0-only
+ *
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+#ifndef __PPE_CONFIG_H__
+#define __PPE_CONFIG_H__
+
+#include "ppe.h"
+
+int ppe_hw_config(struct ppe_device *ppe_dev);
+#endif
diff --git a/drivers/net/ethernet/qualcomm/ppe/ppe_regs.h b/drivers/net/ethernet/qualcomm/ppe/ppe_regs.h
new file mode 100644
index 000000000000..b00f77ec45fe
--- /dev/null
+++ b/drivers/net/ethernet/qualcomm/ppe/ppe_regs.h
@@ -0,0 +1,59 @@
+/* SPDX-License-Identifier: GPL-2.0-only
+ *
+ * Copyright (c) 2025 Qualcomm Innovation Center, Inc. All rights reserved.
+ */
+
+/* PPE hardware register and table declarations. */
+#ifndef __PPE_REGS_H__
+#define __PPE_REGS_H__
+
+#include <linux/bitfield.h>
+
+/* There are 15 BM ports and 4 BM groups supported by PPE.
+ * BM port (0-7) is for EDMA port 0, BM port (8-13) is for
+ * PPE physical port 1-6 and BM port 14 is for EIP port.
+ */
+#define PPE_BM_PORT_FC_MODE_ADDR 0x600100
+#define PPE_BM_PORT_FC_MODE_ENTRIES 15
+#define PPE_BM_PORT_FC_MODE_INC 0x4
+#define PPE_BM_PORT_FC_MODE_EN BIT(0)
+
+#define PPE_BM_PORT_GROUP_ID_ADDR 0x600180
+#define PPE_BM_PORT_GROUP_ID_ENTRIES 15
+#define PPE_BM_PORT_GROUP_ID_INC 0x4
+#define PPE_BM_PORT_GROUP_ID_SHARED_GROUP_ID GENMASK(1, 0)
+
+#define PPE_BM_SHARED_GROUP_CFG_ADDR 0x600290
+#define PPE_BM_SHARED_GROUP_CFG_ENTRIES 4
+#define PPE_BM_SHARED_GROUP_CFG_INC 0x4
+#define PPE_BM_SHARED_GROUP_CFG_SHARED_LIMIT GENMASK(10, 0)
+
+#define PPE_BM_PORT_FC_CFG_TBL_ADDR 0x601000
+#define PPE_BM_PORT_FC_CFG_TBL_ENTRIES 15
+#define PPE_BM_PORT_FC_CFG_TBL_INC 0x10
+#define PPE_BM_PORT_FC_W0_REACT_LIMIT GENMASK(8, 0)
+#define PPE_BM_PORT_FC_W0_RESUME_THRESHOLD GENMASK(17, 9)
+#define PPE_BM_PORT_FC_W0_RESUME_OFFSET GENMASK(28, 18)
+#define PPE_BM_PORT_FC_W0_CEILING_LOW GENMASK(31, 29)
+#define PPE_BM_PORT_FC_W1_CEILING_HIGH GENMASK(7, 0)
+#define PPE_BM_PORT_FC_W1_WEIGHT GENMASK(10, 8)
+#define PPE_BM_PORT_FC_W1_DYNAMIC BIT(11)
+#define PPE_BM_PORT_FC_W1_PRE_ALLOC GENMASK(22, 12)
+
+#define PPE_BM_PORT_FC_SET_REACT_LIMIT(tbl_cfg, value) \
+ u32p_replace_bits((u32 *)tbl_cfg, value, PPE_BM_PORT_FC_W0_REACT_LIMIT)
+#define PPE_BM_PORT_FC_SET_RESUME_THRESHOLD(tbl_cfg, value) \
+ u32p_replace_bits((u32 *)tbl_cfg, value, PPE_BM_PORT_FC_W0_RESUME_THRESHOLD)
+#define PPE_BM_PORT_FC_SET_RESUME_OFFSET(tbl_cfg, value) \
+ u32p_replace_bits((u32 *)tbl_cfg, value, PPE_BM_PORT_FC_W0_RESUME_OFFSET)
+#define PPE_BM_PORT_FC_SET_CEILING_LOW(tbl_cfg, value) \
+ u32p_replace_bits((u32 *)tbl_cfg, value, PPE_BM_PORT_FC_W0_CEILING_LOW)
+#define PPE_BM_PORT_FC_SET_CEILING_HIGH(tbl_cfg, value) \
+ u32p_replace_bits((u32 *)(tbl_cfg) + 0x1, value, PPE_BM_PORT_FC_W1_CEILING_HIGH)
+#define PPE_BM_PORT_FC_SET_WEIGHT(tbl_cfg, value) \
+ u32p_replace_bits((u32 *)(tbl_cfg) + 0x1, value, PPE_BM_PORT_FC_W1_WEIGHT)
+#define PPE_BM_PORT_FC_SET_DYNAMIC(tbl_cfg, value) \
+ u32p_replace_bits((u32 *)(tbl_cfg) + 0x1, value, PPE_BM_PORT_FC_W1_DYNAMIC)
+#define PPE_BM_PORT_FC_SET_PRE_ALLOC(tbl_cfg, value) \
+ u32p_replace_bits((u32 *)(tbl_cfg) + 0x1, value, PPE_BM_PORT_FC_W1_PRE_ALLOC)
+#endif
--
2.34.1
