On Tue, Jan 07, 2025 at 04:38:28PM +0200, Abel Vesa wrote: > On 25-01-07 15:35:07, Abel Vesa wrote: > > On Lenovo ThinkPad T14s, the fingerprint reader placed in the power > > button is connected via the usb_2 controller. The controller has only > > a USB 2.0 PHY which is then connected via a NXP PTN3222 eUSB2 repeater, > > which in turn is connected to the Goodix fingerprint reader. > > > > So enable all the usb_2 controller and PHY nodes, set dual-role mode to > > host and describe the eUSB2 repeater in order to get the fingerprint > > reader discovered. > > > > Signed-off-by: Abel Vesa <abel.vesa@xxxxxxxxxx> > > Turns out that on resume a couple of things are broken w.r.t. to the usb_2 controller: > > [ 41.104913] arm-smmu 15000000.iommu: Unhandled context fault: fsr=0x402, iova=0xe2010600, fsynr=0x110001, cbfrsynra=0x14e0, cb > [ 41.104936] arm-smmu 15000000.iommu: FSR = 00000402 [Format=2 TF], SID=0x14e0 > [ 41.104950] arm-smmu 15000000.iommu: FSYNR0 = 00110001 [S1CBNDX=17 PLVL=1] > [ 51.420689] xhci-hcd xhci-hcd.6.auto: xHCI host not responding to stop endpoint command > [ 51.420702] xhci-hcd xhci-hcd.6.auto: xHCI host controller not responding, assume dead > [ 51.420720] xhci-hcd xhci-hcd.6.auto: HC died; cleaning up > [ 51.420836] usb 5-1: PM: dpm_run_callback(): usb_dev_resume returns -22 > [ 51.420864] usb 5-1: PM: failed to resume async: error -22 > > So do not apply this yet. > > Sorry for not testing this properly before sending. Heh, thanks for the heads up. I was just about to reply with my: Reviewed-by: Johan Hovold <johan+linaro@xxxxxxxxxx> Tested-by: Johan Hovold <johan+linaro@xxxxxxxxxx> after comparing with the schematics and verifying that the fingerprint reader enumerates. But I do indeed see something similar here on resume: [ 1891.737726] arm-smmu 15000000.iommu: Unhandled context fault: fsr=0x402, iova=0xe3f6ddbec0, fsynr=0x510000, cbfrsynra=0x14e0, cb=3 [ 1891.737738] arm-smmu 15000000.iommu: FSR = 00000402 [Format=2 TF], SID=0x14e0 [ 1891.737746] arm-smmu 15000000.iommu: FSYNR0 = 00510000 [S1CBNDX=81 PLVL=0] [ 1891.804342] r8152 7-1:1.0 eth0: carrier on [ 1902.039158] xhci-hcd xhci-hcd.1.auto: xHCI host not responding to stop endpoint command [ 1902.039191] xhci-hcd xhci-hcd.1.auto: xHCI host controller not responding, assume dead [ 1902.039795] xhci-hcd xhci-hcd.1.auto: HC died; cleaning up [ 1902.040050] usb 1-1: PM: dpm_run_callback(): usb_dev_resume returns -5 [ 1902.040272] usb 1-1: PM: failed to resume async: error -5 [ 1902.581479] OOM killer enabled. [ 1902.586673] Restarting tasks ... [ 1902.587565] usb 1-1: USB disconnect, device number 2 Johan
