Add configuration nodes for following devices:
* GPIO block, with 36 pins
* MPP block, with 8 pins
* Current ADC (IADC)
* Volatage ADC (VADC), with multiple inputs
* Thermal sensor device, which is using on chip VADC
channel report PMIC die temperature
* Power key device, which is responsible for clean system
reboot or shutdown
* White LED device
* RTC device
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@xxxxxxxxxx>
---
arch/arm/boot/dts/qcom-pm8941.dtsi | 133 ++++++++++++++++++++++++++++++++++++-
1 file changed, 132 insertions(+), 1 deletion(-)
diff --git a/arch/arm/boot/dts/qcom-pm8941.dtsi b/arch/arm/boot/dts/qcom-pm8941.dtsi
index 24c5088..aa774e6 100644
--- a/arch/arm/boot/dts/qcom-pm8941.dtsi
+++ b/arch/arm/boot/dts/qcom-pm8941.dtsi
@@ -1,3 +1,5 @@
+#include <dt-bindings/iio/qcom,spmi-vadc.h>
+#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
&spmi_bus {
@@ -7,12 +9,141 @@
reg = <0x0 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
+
+ rtc@6000 {
+ compatible = "qcom,pm8941-rtc";
+ reg = <0x6000 0x100>,
+ <0x6100 0x100>;
+ reg-names = "rtc", "alarm";
+ interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
+ };
+
+ pwrkey@800 {
+ compatible = "qcom,pm8941-pwrkey";
+ reg = <0x800 0x100>;
+ interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
+ debounce = <15625>;
+ bias-pull-up;
+ };
+
+ pm8941_gpios: gpios@c000 {
+ compatible = "qcom,pm8941-gpio";
+ reg = <0xc000 0x2400>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <0 0xc0 0 IRQ_TYPE_NONE>,
+ <0 0xc1 0 IRQ_TYPE_NONE>,
+ <0 0xc2 0 IRQ_TYPE_NONE>,
+ <0 0xc3 0 IRQ_TYPE_NONE>,
+ <0 0xc4 0 IRQ_TYPE_NONE>,
+ <0 0xc5 0 IRQ_TYPE_NONE>,
+ <0 0xc6 0 IRQ_TYPE_NONE>,
+ <0 0xc7 0 IRQ_TYPE_NONE>,
+ <0 0xc8 0 IRQ_TYPE_NONE>,
+ <0 0xc9 0 IRQ_TYPE_NONE>,
+ <0 0xca 0 IRQ_TYPE_NONE>,
+ <0 0xcb 0 IRQ_TYPE_NONE>,
+ <0 0xcc 0 IRQ_TYPE_NONE>,
+ <0 0xcd 0 IRQ_TYPE_NONE>,
+ <0 0xce 0 IRQ_TYPE_NONE>,
+ <0 0xcf 0 IRQ_TYPE_NONE>,
+ <0 0xd0 0 IRQ_TYPE_NONE>,
+ <0 0xd1 0 IRQ_TYPE_NONE>,
+ <0 0xd2 0 IRQ_TYPE_NONE>,
+ <0 0xd3 0 IRQ_TYPE_NONE>,
+ <0 0xd4 0 IRQ_TYPE_NONE>,
+ <0 0xd5 0 IRQ_TYPE_NONE>,
+ <0 0xd6 0 IRQ_TYPE_NONE>,
+ <0 0xd7 0 IRQ_TYPE_NONE>,
+ <0 0xd8 0 IRQ_TYPE_NONE>,
+ <0 0xd9 0 IRQ_TYPE_NONE>,
+ <0 0xda 0 IRQ_TYPE_NONE>,
+ <0 0xdb 0 IRQ_TYPE_NONE>,
+ <0 0xdc 0 IRQ_TYPE_NONE>,
+ <0 0xdd 0 IRQ_TYPE_NONE>,
+ <0 0xde 0 IRQ_TYPE_NONE>,
+ <0 0xdf 0 IRQ_TYPE_NONE>,
+ <0 0xe0 0 IRQ_TYPE_NONE>,
+ <0 0xe1 0 IRQ_TYPE_NONE>,
+ <0 0xe2 0 IRQ_TYPE_NONE>,
+ <0 0xe3 0 IRQ_TYPE_NONE>;
+ };
+
+ pm8941_mpps: mpps@a000 {
+ compatible = "qcom,pm8941-mpp";
+ reg = <0xa000 0x800>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupts = <0 0xa0 0 IRQ_TYPE_NONE>,
+ <0 0xa1 0 IRQ_TYPE_NONE>,
+ <0 0xa2 0 IRQ_TYPE_NONE>,
+ <0 0xa3 0 IRQ_TYPE_NONE>,
+ <0 0xa4 0 IRQ_TYPE_NONE>,
+ <0 0xa5 0 IRQ_TYPE_NONE>,
+ <0 0xa6 0 IRQ_TYPE_NONE>,
+ <0 0xa7 0 IRQ_TYPE_NONE>;
+ };
+
+ pm8941_temp: temp-alarm@2400 {
+ compatible = "qcom,spmi-temp-alarm";
+ reg = <0x2400 0x100>;
+ interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
+ io-channels = <&pm8941_vadc VADC_DIE_TEMP>;
+ io-channel-names = "thermal";
+ #thermal-sensor-cells = <0>;
+ };
+
+ pm8941_vadc: vadc@3100 {
+ compatible = "qcom,spmi-vadc";
+ reg = <0x3100 0x100>;
+ interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+
+ die_temp {
+ reg = <VADC_DIE_TEMP>;
+ };
+ ref_625mv {
+ reg = <VADC_REF_625MV>;
+ };
+ ref_1250v {
+ reg = <VADC_REF_1250MV>;
+ };
+ ref_gnd {
+ reg = <VADC_GND_REF>;
+ };
+ ref_vdd {
+ reg = <VADC_VDD_VADC>;
+ };
+ };
+
+ pm8941_iadc: iadc@3600 {
+ compatible = "qcom,pm8941-iadc", "qcom,spmi-iadc";
+ reg = <0x3600 0x100>,
+ <0x12f1 0x1>;
+ interrupts = <0x0 0x36 0x0 IRQ_TYPE_EDGE_RISING>;
+ qcom,external-resistor-micro-ohms = <10000>;
+ };
};
usid1: pm8941@1 {
- compatible ="qcom,spmi-pmic";
+ compatible = "qcom,spmi-pmic";
reg = <0x1 SPMI_USID>;
#address-cells = <1>;
#size-cells = <0>;
+
+ wled@d800 {
+ compatible = "qcom,pm8941-wled";
+ reg = <0xd800 0x100>;
+ label = "backlight";
+
+ qcom,cs-out;
+ qcom,current-limit = <20>;
+ qcom,current-boost-limit = <805>;
+ qcom,switching-freq = <1600>;
+ qcom,ovp = <29>;
+ qcom,num-strings = <2>;
+ };
};
};
--
1.9.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
