Re: [PATCH 2/2] arm64: dts: imx95: add ENETC 0 support

[Frank Li <Frank.li@xxxxxxx>]

On Wed, Dec 18, 2024 at 02:17:25PM +0800, Wei Fang wrote:

nit: arm64: dts: imx95-19x19-evk: add ENETC 0 support

> Add ENETC 0 (1G ethernet port) support for i.MX95-19x19-EVK board. In
> addition, because all ENETC instances share MDIO bus, so enable EMDIO
> at the same time.
>
> Signed-off-by: Wei Fang <wei.fang@xxxxxxx>
> ---
>  .../boot/dts/freescale/imx95-19x19-evk.dts    | 52 +++++++++++++++++++
>  1 file changed, 52 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
> index 6086cb7fa5a0..e838234c8317 100644
> --- a/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
> +++ b/arch/arm64/boot/dts/freescale/imx95-19x19-evk.dts
> @@ -38,6 +38,7 @@ aliases {
>  		mmc0 = &usdhc1;
>  		mmc1 = &usdhc2;
>  		serial0 = &lpuart1;
> +		ethernet0 = &enetc_port0;
>  	};
>
>  	bt_sco_codec: audio-codec-bt-sco {
> @@ -428,6 +429,33 @@ &wdog3 {
>  	status = "okay";
>  };
>
> +&netcmix_blk_ctrl {
> +	status = "okay";
> +};
> +
> +&netc_blk_ctrl {
> +	status = "okay";
> +};
> +
> +&enetc_port0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_enetc0>;
> +	phy-handle = <&ethphy0>;
> +	phy-mode = "rgmii-id";
> +	status = "okay";
> +};
> +
> +&netc_emdio {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&pinctrl_emdio>;
> +	status = "okay";
> +
> +	ethphy0: ethernet-phy@1 {
> +		reg = <1>;
> +		realtek,clkout-disable;
> +	};
> +};

Please keep order by these node. netc should after enetc

> +
>  &scmi_iomuxc {
>  	pinctrl_flexspi1: flexspi1grp {
>  		fsl,pins = <
> @@ -665,6 +693,30 @@ IMX95_PAD_SD2_DATA3__USDHC2_DATA3		0x13fe
>  			IMX95_PAD_SD2_VSELECT__USDHC2_VSELECT		0x51e
>  		>;
>  	};
> +
> +	pinctrl_enetc0: enetc0grp {
> +		fsl,pins = <
> +			IMX95_PAD_ENET1_TD3__NETCMIX_TOP_ETH0_RGMII_TD3		0x57e
> +			IMX95_PAD_ENET1_TD2__NETCMIX_TOP_ETH0_RGMII_TD2		0x57e
> +			IMX95_PAD_ENET1_TD1__NETCMIX_TOP_ETH0_RGMII_TD1		0x57e
> +			IMX95_PAD_ENET1_TD0__NETCMIX_TOP_ETH0_RGMII_TD0		0x57e
> +			IMX95_PAD_ENET1_TX_CTL__NETCMIX_TOP_ETH0_RGMII_TX_CTL	0x57e
> +			IMX95_PAD_ENET1_TXC__NETCMIX_TOP_ETH0_RGMII_TX_CLK	0x58e
> +			IMX95_PAD_ENET1_RX_CTL__NETCMIX_TOP_ETH0_RGMII_RX_CTL	0x57e
> +			IMX95_PAD_ENET1_RXC__NETCMIX_TOP_ETH0_RGMII_RX_CLK	0x58e
> +			IMX95_PAD_ENET1_RD0__NETCMIX_TOP_ETH0_RGMII_RD0		0x57e
> +			IMX95_PAD_ENET1_RD1__NETCMIX_TOP_ETH0_RGMII_RD1		0x57e
> +			IMX95_PAD_ENET1_RD2__NETCMIX_TOP_ETH0_RGMII_RD2		0x57e
> +			IMX95_PAD_ENET1_RD3__NETCMIX_TOP_ETH0_RGMII_RD3		0x57e
> +		>;
> +	};
> +
> +	pinctrl_emdio: emdiogrp{
> +		fsl,pins = <
> +			IMX95_PAD_ENET1_MDC__NETCMIX_TOP_NETC_MDC		0x57e
> +			IMX95_PAD_ENET1_MDIO__NETCMIX_TOP_NETC_MDIO		0x97e
> +		>;
> +	};

some here, keep order,
enetc0grp should before flexspi1grp

Frank

>  };
>
>  &thermal_zones {
> --
> 2.34.1
>