On 12/5/24 18:27, Bjorn Helgaas wrote:
On Tue, Nov 26, 2024 at 04:51:18PM +0100, Christian Bruel wrote:
Add driver to configure the STM32MP25 SoC PCIe Gen2 controller based on the
DesignWare PCIe core in endpoint mode.
+config PCIE_STM32_EP
+ tristate "STMicroelectronics STM32MP25 PCIe Controller (endpoint mode)"
+ depends on ARCH_STM32 || COMPILE_TEST
+ depends on PCI_ENDPOINT
+ select PCIE_DW_EP
+ help
+ Enables endpoint support for DesignWare core based PCIe controller in found
+ in STM32MP25 SoC.
s/in found in/in/ (or "found in" if you prefer)
Wrap so help text fits in 80 columns when for "make menuconfig".
+static void stm32_pcie_ep_init(struct dw_pcie_ep *ep)
+{
+ struct dw_pcie *pci = to_dw_pcie_from_ep(ep);
+ struct stm32_pcie *stm32_pcie = to_stm32_pcie(pci);
+ enum pci_barno bar;
+
+ for (bar = 0; bar < PCI_STD_NUM_BARS; bar++)
+ dw_pcie_ep_reset_bar(pci, bar);
+
+ /* Defer Completion Requests until link started */
I asked about this before [1] but didn't finish the conversation. My
main point is that I think "Completion Request" is a misnomer.
There's a "Configuration Request" and a "Completion," but no such
thing as a "Completion Request."
Based on your previous response, I think this should say something
like "respond to config requests with Request Retry Status (RRS) until
we're prepared to handle them."
OK thanks for the phrasing. This is inline with the DWC doc:
"... controller completes incoming configuration requests with a
configuration request retry status."
The only thing is that the PCIe specs talks about CRS, not RRS.
so slightly change to
"respond to config requests with Configuration Request Retry Status
(CRS) until we're prepared to handle them."
+ regmap_update_bits(stm32_pcie->regmap, SYSCFG_PCIECR,
+ STM32MP25_PCIECR_REQ_RETRY_EN,
+ STM32MP25_PCIECR_REQ_RETRY_EN);
+}
+
+static int stm32_pcie_enable_link(struct dw_pcie *pci)
+{
+ struct stm32_pcie *stm32_pcie = to_stm32_pcie(pci);
+ int ret;
+
+ regmap_update_bits(stm32_pcie->regmap, SYSCFG_PCIECR,
+ STM32MP25_PCIECR_LTSSM_EN,
+ STM32MP25_PCIECR_LTSSM_EN);
+
+ ret = dw_pcie_wait_for_link(pci);
+ if (ret)
+ return ret;
+
+ regmap_update_bits(stm32_pcie->regmap, SYSCFG_PCIECR,
+ STM32MP25_PCIECR_REQ_RETRY_EN,
+ 0);
And I assume this means the endpoint will accept config requests and
handle them normally instead of responding with RRS.
Strictly speaking this is a different condition than "the link is up"
because the link must be up in order to even receive a config request.
The purpose of RRS is for devices that need more initialization time
after the link is up before they can respond to config requests.
The fact that the hardware provides this bit makes me think the
designer anticipated that the link might come up before the rest of
the device is fully initialized.
Agree, this there are 2 conditions in this function: link is up +
accepting config requests. I'll split or rename
Thanks
Christian
Bjorn
[1] https://lore.kernel.org/r/20241112203846.GA1856246@bhelgaas
