Le 12/12/2024 à 23:26, Frank Li a écrit :
From: Joy Zou <joy.zou-3arQi8VN3Tc@xxxxxxxxxxxxxxxx>
Support new PMIC PF9453, which is totally difference with PCA9450. So
create new file for it.
The PF9453 is a single chip Power Management IC (PMIC) specifically
designed for i.MX 91 processor. It provides power supply solutions for IoT
(Internet of Things), smart appliance, and portable applications where size
and efficiency are critical. The device provides four high efficiency
step-down regulators, three LDOs, one 400 mA load switch and 32.768 kHz
crystal oscillator driver.
Hi, a few nitpicks, should a v3 be needed.
...
+static int pf9453_i2c_probe(struct i2c_client *i2c)
+{
+ const struct pf9453_regulator_desc *regulator_desc = of_device_get_match_data(&i2c->dev);
+ struct regulator_config config = { };
+ unsigned int reset_ctrl;
+ unsigned int device_id;
+ struct pf9453 *pf9453;
+ int ret;
+
+ if (!i2c->irq)
+ return dev_err_probe(&i2c->dev, -EINVAL, "No IRQ configured?\n");
+
+ pf9453 = devm_kzalloc(&i2c->dev, sizeof(struct pf9453), GFP_KERNEL);
+ if (!pf9453)
+ return -ENOMEM;
+
+ pf9453->regmap = devm_regmap_init_i2c(i2c, &pf9453_regmap_config);
+ if (IS_ERR(pf9453->regmap))
+ return dev_err_probe(&i2c->dev, PTR_ERR(pf9453->regmap),
+ "regmap initialization failed\n");
+
+ pf9453->irq = i2c->irq;
+ pf9453->dev = &i2c->dev;
+
+ dev_set_drvdata(&i2c->dev, pf9453);
+
+ ret = regmap_read(pf9453->regmap, PF9453_REG_DEV_ID, &device_id);
+ if (ret)
+ return dev_err_probe(&i2c->dev, ret, "Read device id error\n");
Nitpick: 2 spaces
+
+ /* Check your board and dts for match the right pmic */
+ if ((device_id >> 4) != 0xB)
+ return dev_err_probe(&i2c->dev, -EINVAL, "Device id(%x) mismatched\n",
+ device_id >> 4);
+
+ while (regulator_desc->desc.name) {
+ const struct regulator_desc *desc;
+ struct regulator_dev *rdev;
+
+ desc = ®ulator_desc->desc;
+
+ config.regmap = pf9453->regmap;
+ config.dev = pf9453->dev;
+
+ rdev = devm_regulator_register(pf9453->dev, desc, &config);
+ if (IS_ERR(rdev))
+ return dev_err_probe(pf9453->dev, PTR_ERR(rdev),
+ "Failed to register regulator(%s)\n", desc->name);
+
+ regulator_desc++;
+ }
+
+ ret = devm_request_threaded_irq(pf9453->dev, pf9453->irq, NULL,
+ pf9453_irq_handler,
+ (IRQF_TRIGGER_FALLING | IRQF_ONESHOT),
+ "pf9453-irq", pf9453);
+ if (ret)
+ return dev_err_probe(pf9453->dev, ret, "Failed to request IRQ: %d\n", pf9453->irq);
+
+ /* Unmask all interrupt except PWRON/WDOG/RSVD */
+ ret = pf9453_pmic_write(pf9453, PF9453_REG_INT1_MSK,
+ IRQ_ONKEY | IRQ_RESETKEY | IRQ_RSTB | IRQ_VR_FLT1
+ | IRQ_LOWVSYS | IRQ_THERM_100 | IRQ_THERM_80,
+ IRQ_RSVD);
+ if (ret)
+ return dev_err_probe(&i2c->dev, ret, "Unmask irq error\n");
Nitpick: 2 spaces
+
+ if (of_property_read_bool(i2c->dev.of_node, "nxp,wdog_b-warm-reset"))
+ reset_ctrl = WDOG_B_CFG_WARM;
+ else
+ reset_ctrl = WDOG_B_CFG_COLD;
...
diff --git a/drivers/regulator/pf9453.h b/drivers/regulator/pf9453.h
new file mode 100644
index 0000000000000..14d6343d42658
--- /dev/null
+++ b/drivers/regulator/pf9453.h
@@ -0,0 +1,171 @@
+/* SPDX-License-Identifier: GPL-2.0-or-later */
+/* Copyright 2024 NXP. */
+
+#ifndef __LINUX_REG_PF9453_H__
+#define __LINUX_REG_PF9453_H__
+
+#include <linux/regmap.h>
This .h file does not need it.
Should it be placed in the .c file?
+
+enum {
+ PF9453_BUCK1 = 0,
+ PF9453_BUCK2,
+ PF9453_BUCK3,
+ PF9453_BUCK4,
+ PF9453_LDO1,
+ PF9453_LDO2,
+ PF9453_LDOSNVS,
+ PF9453_REGULATOR_CNT,
Nitpick: such terminator don't need an ending comma
+};
+
+enum {
+ PF9453_DVS_LEVEL_RUN = 0,
+ PF9453_DVS_LEVEL_STANDBY,
+ PF9453_DVS_LEVEL_DPSTANDBY,
+ PF9453_DVS_LEVEL_MAX,
Nitpick: such terminator don't need an ending comma
+};
...
+enum {
+ PF9453_REG_DEV_ID = 0x00,
+ PF9453_REG_OTP_VER = 0x01,
+ PF9453_REG_INT1 = 0x02,
+ PF9453_REG_INT1_MSK = 0x03,
+ PF9453_REG_INT1_STATUS = 0x04,
+ PF9453_REG_VRFLT1_INT = 0x05,
+ PF9453_REG_VRFLT1_MASK = 0x06,
+ PF9453_REG_PWRON_STAT = 0x07,
+ PF9453_REG_RESET_CTRL = 0x08,
+ PF9453_REG_SW_RST = 0x09,
+ PF9453_REG_PWR_CTRL = 0x0a,
+ PF9453_REG_CONFIG1 = 0x0b,
+ PF9453_REG_CONFIG2 = 0x0c,
+ PF9453_REG_32K_CONFIG = 0x0d,
+ PF9453_REG_BUCK1CTRL = 0x10,
+ PF9453_REG_BUCK1OUT = 0x11,
+ PF9453_REG_BUCK2CTRL = 0x14,
+ PF9453_REG_BUCK2OUT = 0x15,
+ PF9453_REG_BUCK2OUT_STBY = 0x1D,
+ PF9453_REG_BUCK2OUT_MAX_LIMIT = 0x1F,
+ PF9453_REG_BUCK2OUT_MIN_LIMIT = 0x20,
+ PF9453_REG_BUCK3CTRL = 0x21,
+ PF9453_REG_BUCK3OUT = 0x22,
+ PF9453_REG_BUCK4CTRL = 0x2e,
+ PF9453_REG_BUCK4OUT = 0x2f,
+ PF9453_REG_LDO1OUT_L = 0x36,
+ PF9453_REG_LDO1CFG = 0x37,
+ PF9453_REG_LDO1OUT_H = 0x38,
+ PF9453_REG_LDOSNVS_CFG1 = 0x39,
+ PF9453_REG_LDOSNVS_CFG2 = 0x3a,
+ PF9453_REG_LDO2CFG = 0x3b,
+ PF9453_REG_LDO2OUT = 0x3c,
+ PF9453_REG_BUCK_POK = 0x3d,
+ PF9453_REG_LSW_CTRL1 = 0x40,
+ PF9453_REG_LSW_CTRL2 = 0x41,
+ PF9453_REG_LOCK = 0x4e,
+ PF9453_MAX_REG,
Nitpick: such terminator don't need an ending comma
+};
+
+#define PF9453_UNLOCK_KEY 0x5c
+#define PF9453_LOCK_KEY 0x0
+
+/* PF9453 BUCK ENMODE bits */
+#define BUCK_ENMODE_OFF 0x00
+#define BUCK_ENMODE_ONREQ 0x01
+#define BUCK_ENMODE_ONREQ_STBY 0x02
+#define BUCK_ENMODE_ONREQ_STBY_DPSTBY 0x03
+
+/* PF9453 BUCK ENMODE bits */
+#define LDO_ENMODE_OFF 0x00
+#define LDO_ENMODE_ONREQ 0x01
+#define LDO_ENMODE_ONREQ_STBY 0x02
+#define LDO_ENMODE_ONREQ_STBY_DPSTBY 0x03
+
+/* PF9453_REG_BUCK1_CTRL bits */
+#define BUCK1_LPMODE 0x30
+#define BUCK1_AD 0x08
+#define BUCK1_FPWM 0x04
+#define BUCK1_ENMODE_MASK 0x03
+
+/* PF9453_REG_BUCK2_CTRL bits */
+#define BUCK2_RAMP_MASK 0xC0
Here and below some uppercase alpha are used, while above only lowercase
are used. Below is apparently for masks.
Maybe masks could be written with GENMASK()?
(no strong opinion if this would help readability)
+#define BUCK2_RAMP_25MV 0x0
+#define BUCK2_RAMP_12P5MV 0x1
+#define BUCK2_RAMP_6P25MV 0x2
+#define BUCK2_RAMP_3P125MV 0x3
+#define BUCK2_LPMODE 0x30
+#define BUCK2_AD 0x08
+#define BUCK2_FPWM 0x04
+#define BUCK2_ENMODE_MASK 0x03
...
CJ
