On 2024/12/10 19:02, Dmitry Baryshkov wrote:
On Tue, Dec 10, 2024 at 02:54:00PM +0800, Fange Zhang wrote:From: Li Liu <quic_lliu6@xxxxxxxxxxx> Add display MDSS and DSI configuration for QCS615 RIDE board. QCS615 has a DP port, and DP support will be added in a later patch. Signed-off-by: Li Liu <quic_lliu6@xxxxxxxxxxx> Signed-off-by: Fange Zhang <quic_fangez@xxxxxxxxxxx> --- arch/arm64/boot/dts/qcom/qcs615-ride.dts | 89 ++++++++++++++++++++++++++++++++ 1 file changed, 89 insertions(+) diff --git a/arch/arm64/boot/dts/qcom/qcs615-ride.dts b/arch/arm64/boot/dts/qcom/qcs615-ride.dts index a25928933e2b66241258e418c6e5bc36c306101e..694719a09ac46bfa2fe34f1883c0970b9d0902be 100644 --- a/arch/arm64/boot/dts/qcom/qcs615-ride.dts +++ b/arch/arm64/boot/dts/qcom/qcs615-ride.dts @@ -32,6 +32,18 @@ xo_board_clk: xo-board-clk { #clock-cells = <0>; }; }; + + dp-connector { + compatible = "dp-connector"; + label = "DP"; + type = "mini"; + + port { + dp_connector_out: endpoint { + remote-endpoint = <&anx_7625_out>; + }; + }; + }; };&apps_rsc {@@ -202,6 +214,83 @@ &gcc { <&sleep_clk>; };+&i2c2 {+ clock-frequency = <400000>; + status = "okay"; + + ioexp: gpio@3e { + compatible = "semtech,sx1509q"; + reg = <0x3e>; + interrupt-parent = <&tlmm>; + interrupts = <58 0>;Use IRQ flags instead of just 0 (here and further on). Also it might be better to use interrupts-extended instead.
Got it, will use interrupts-extended instead - interrupt-parent = <&tlmm>; - interrupts = <58 0>; + interrupts-extended = <&tlmm 58 IRQ_TYPE_NONE>;
+ gpio-controller; + #gpio-cells = <2>; + interrupt-controller; + #interrupt-cells = <2>; + semtech,probe-reset; + }; + + i2c-mux@77 { + compatible = "nxp,pca9542"; + reg = <0x77>; + #address-cells = <1>; + #size-cells = <0>;Add empty line before device nodes (here and furher on).
Sorry, will add it in next patch.
+ i2c@0 { + reg = <0>; + #address-cells = <1>; + #size-cells = <0>; + + anx7625@58 { + compatible = "analogix,anx7625"; + reg = <0x58>; + interrupt-parent = <&ioexp>; + interrupts = <0 0>;
will change it to interrupts-extended in next patch - interrupt-parent = <&ioexp>; - interrupts = <0 0>; + interrupts-extended = <&ioexp 0 IRQ_TYPE_NONE>;
+ enable-gpios = <&tlmm 4 GPIO_ACTIVE_HIGH>; + reset-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>; + wakeup-source; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + anx_7625_in: endpoint { + remote-endpoint = <&mdss_dsi0_out>; + }; + }; + + port@1 { + reg = <1>; + anx_7625_out: endpoint { + remote-endpoint = <&dp_connector_out>; + }; + }; + }; + }; + }; + }; +}; + +&mdss { + status = "okay"; +}; + +&mdss_dsi0 { + vdda-supply = <&vreg_l11a>; + status = "okay"; +}; + +&mdss_dsi0_out { + remote-endpoint = <&anx_7625_in>; + data-lanes = <0 1 2 3>; +}; + +&mdss_dsi0_phy { + vdds-supply = <&vreg_l5a>; + status = "okay"; +}; + &qupv3_id_0 { status = "okay"; }; -- 2.34.1
