The behavior of pins in deep sleep mode can be configured by programming the corresponding bits in the respective Pad Configuration register. Add macros to support this. Signed-off-by: Siddharth Vadapalli <s-vadapalli@xxxxxx> --- v1: https://lore.kernel.org/r/20241112115650.988943-2-s-vadapalli@xxxxxx Changes since v1: - Rebased on next-20241204. While Rob had suggested dropping the zero defines at: https://lore.kernel.org/r/20241115154822.GA2954187-robh@xxxxxxxxxx/ I had pointed out the inconsistency with existing convention at: https://lore.kernel.org/r/5b35c736-74d6-4fe9-ae82-272dc2e98b82@xxxxxx/ asking for Rob's opinion. Since I didn't receive a reply, I assumed that the patch is fine in terms of being consistent and hence haven't dropped the zero defines in the current version. Regards, Siddharth. arch/arm64/boot/dts/ti/k3-pinctrl.h | 19 +++++++++++++++++++ 1 file changed, 19 insertions(+) diff --git a/arch/arm64/boot/dts/ti/k3-pinctrl.h b/arch/arm64/boot/dts/ti/k3-pinctrl.h index 22b8d73cfd32..cac7cccc1112 100644 --- a/arch/arm64/boot/dts/ti/k3-pinctrl.h +++ b/arch/arm64/boot/dts/ti/k3-pinctrl.h @@ -12,6 +12,12 @@ #define PULLTYPESEL_SHIFT (17) #define RXACTIVE_SHIFT (18) #define DEBOUNCE_SHIFT (11) +#define FORCE_DS_EN_SHIFT (15) +#define DS_EN_SHIFT (24) +#define DS_OUT_DIS_SHIFT (25) +#define DS_OUT_VAL_SHIFT (26) +#define DS_PULLUD_EN_SHIFT (27) +#define DS_PULLTYPE_SEL_SHIFT (28) #define PULL_DISABLE (1 << PULLUDEN_SHIFT) #define PULL_ENABLE (0 << PULLUDEN_SHIFT) @@ -38,6 +44,19 @@ #define PIN_DEBOUNCE_CONF5 (5 << DEBOUNCE_SHIFT) #define PIN_DEBOUNCE_CONF6 (6 << DEBOUNCE_SHIFT) +#define PIN_DS_FORCE_DISABLE (0 << FORCE_DS_EN_SHIFT) +#define PIN_DS_FORCE_ENABLE (1 << FORCE_DS_EN_SHIFT) +#define PIN_DS_IO_OVERRIDE_DISABLE (0 << DS_IO_OVERRIDE_EN_SHIFT) +#define PIN_DS_IO_OVERRIDE_ENABLE (1 << DS_IO_OVERRIDE_EN_SHIFT) +#define PIN_DS_OUT_ENABLE (0 << DS_OUT_DIS_SHIFT) +#define PIN_DS_OUT_DISABLE (1 << DS_OUT_DIS_SHIFT) +#define PIN_DS_OUT_VALUE_ZERO (0 << DS_OUT_VAL_SHIFT) +#define PIN_DS_OUT_VALUE_ONE (1 << DS_OUT_VAL_SHIFT) +#define PIN_DS_PULLUD_ENABLE (0 << DS_PULLUD_EN_SHIFT) +#define PIN_DS_PULLUD_DISABLE (1 << DS_PULLUD_EN_SHIFT) +#define PIN_DS_PULL_DOWN (0 << DS_PULLTYPE_SEL_SHIFT) +#define PIN_DS_PULL_UP (1 << DS_PULLTYPE_SEL_SHIFT) + /* Default mux configuration for gpio-ranges to use with pinctrl */ #define PIN_GPIO_RANGE_IOPAD (PIN_INPUT | 7) -- 2.43.0
