Hi Dikshita, On 20/11/2024 15:45, Dikshita Agarwal wrote: > Introduce support for Qualcomm new video acceleration hardware i.e. > iris, used for video stream decoding. > > Iris is a multi pipe based hardware that offloads video stream decoding > from the application processor (AP). It supports H.264 decoding. The AP > communicates with hardware through a well defined protocol, called as > host firmware interface (HFI), which provides fine-grained and > asynchronous control over individual hardware features. > > This driver implements upgraded HFI gen2 to communicate with firmware. > It supports SM8550 which is based out of HFI gen 2. It also supports > SM8250 which is based out of HFI gen1. > > This driver comes with below capabilities: > - V4L2 complaint video driver with M2M and STREAMING capability. > - Supports H264 decoder. > > This driver comes with below features: > - Centralized resource management. > - Centralized management of core and instance states. > - Defines platform specific capabilities and features. As a results, it > provides a single point of control to enable/disable a given feature > depending on specific platform capabilities. > - Handles various video recommended sequences, like DRC, Drain, Seek, > EOS. > - Implements asynchronous communication with hardware to achieve better > experience in low latency usecases. > - Output and capture planes are controlled independently. Thereby > providing a way to reconfigure individual plane. > - Native hardware support of LAST flag which is mandatory to align with > port reconfiguration and DRAIN sequence as per V4L guidelines. I finished my review of v6. I didn't review patches that deal with the HW internals, I focussed on the use of the vb2 and V4L2 framework APIs. Regards, Hans > > Changes since v5: > - Fixed the memory leak in firmware load (Bryan) > - Updated all headers s/_LIKE_SO_/__LIKE_SO__ (Bryan) > - Updated value of IFACEQ_MAX_BUF_COUNT to 64 (Bryan) > - Removed actual_count from iris buffer structure and cleaned up > vb2_queue_setup (Hans) > - Used VIDEO_MAX_FRAME to set actual buffer to firmware (Hans) > - Fixed the typo in commit log and subject of patch#12 (Hans) > - Updated card field to Iris Decoder (Hans) > - Removed redundant setting of byteused (Hans) > - s/iris_driver/is_iris_driver (Jianhua) > - Addressed all other review comments. > - Link to v5: https://lore.kernel.org/r/20241105-qcom-video-iris-v5-0-a88e7c220f78@xxxxxxxxxxx > > Changes since v4: > - Fixed commit message length for all patches (Krzysztof) > - Migrated back to remove from remove_new (Uwe Kleine-König) > - Removed support for g_volatle_ctrl (Hans) > - Added changes to update minimum buffer count whenever the hardware > requirement changes (Hans) > - Removed state checks from try/g/s_fmt ioctls (Hans) > - Removed wait_prepare() and wait_finish callbacks (Hans) > - Added support for remove_bufs (Hans) > - Added module param based configurability to select between venus and > iris drivers for platforms supported by both drivers (Jianhua, Dmitry) > - Addressed misc other review comments from Hans. > - Fixed issues reported by kernel bot. > - Link to v4: https://lore.kernel.org/r/20241014-qcom-video-iris-v4-v4-0-c5eaa4e9ab9e@xxxxxxxxxxx > > Changes since v3: > - Fixed the style issues with dt binding (Krzysztof) > - Pushed the patch to add maintainers to end of the series (Krzysztof, > Dmitry) > - Moved the resource initialization next to probe in iris_probe.c and > squashed the patch of probe and resource initialization (Krzysztof) > - Removed error prints from probe function (Krzysztof) > - Defined bit fields used for register read/write with macros for better > context (Bryan) > - Converted if/else to switch/case wherever applicable (Bryan) > - Removed defensive NULL checks wherever not required (Bryan, Krzysztof) > - Removed core->state checks except for below scenarios (Bryan) > - When reverse thread (firmware) can move the state of the core to > error state. > - When client can force close the driver and there are still pending > firmware responses to be read from shared queues (msg and dbg) > - For PM operations, since its a delayed autosuspend work and sys > error handler from the reverse thread can move the state to core > deinit state anytime. > - Acquiring core->lock only for below scenarios (Bryan) > - Writing to registers. > - Reading/Writing from/to shared queues. > - Traversing the instance list of core. > - To protect the core->state when it can changed by reverse thread. > - Acquiring inst->lock only for below scenario which is needed (Bryan) > - Serializing the forward and reverse thread > - To protect the inst structure where the values can be modified by > firmware. > - Removed usage of core->power_enabled (Krzysztof, Bryan) > - Removed usage of mutex_is_locked (Krzysztof, Bryan) > - Use C structure for instance caps (Dmitry) > - Split the ctrl ops patch by keeping only the defines, struct and caps > needed to intialize the ctrl handler and to implement s/g_ctrl > (Dmitry) > - Removed the instance state checks to allow v4l2-ctl, relying on > standard vb2 checks instead. (Hans) > - Converted APIs to void wherever applicable except for below (Bryan) > - iris_hfi_gen2_handle_session_error and > iris_hfi_gen2_handle_session_property cannot be converted to void > even though they always return 0. > Because these are two of the handlers invoked from > iris_hfi_gen2_handle_session_response and are of > iris_hfi_gen2_inst_hfi_range struct type, where same prototype is > followed for all handlers and return type of all handers should be > 'int'. > And we cannot have a switch case/if else to handle these > responses from firmware because we need to parse the responses in a > particular sequence. > That's why we opted for this handler based design instead of > introducing multiple for loop with code duplication. > - Fixed issues reported by kernel bot. > - Fixed v4l2 compliance issue reported with "-s" options based on the > inputs from Hans. > - Addressed all other review comments and made some code improvements. > > Changes since v2: > - introduced support for HFI gen1. > - deprecated Encoder and HEVC, VP9 codecs. > - removed custom vb2 mem ops and used standard framework instead. > - added support for mmap streaming mode. > - migrated all the buffer APIs to mem2mem helper functions. > - registered iris buffer with vb2 framework. > - migrated to clk_bulk, reset_bulk and icc_bulk APIs. > - used pm_domain_attach/detach_list APIs. > - migrated to read/writel and other available helpers for register > access instead of custom wrappers. > - added documentation for various structures. > - addressed many other review comments from v2. > > Note: A harmless onetime error log "Lucid PLL latch failed. Output may > be unstable!" is seen during bootup. It doesn't impact any video > usecase and is currently under discussion. > > Static tools like checkpatch, smatch, dt_binding_check, sparse and > Coccinelle run successfully with this driver. > > This driver is tested with v4l2-ctl[1] and Gstreamer[2]. > > [1]: v4l2-ctl --verbose --set-fmt-video-out=pixelformat=H264 > --set-fmt-video=pixelformat=NV12 --stream-mmap --stream-out-mmap > --stream-from /media/FVDO_Freeway_720p.264 --stream-to out.NV12 > > [2]: gst-launch-1.0 filesrc location=/media/media/4k_decode_clip.264 ! > h264parse ! v4l2h264dec capture-io-mode=dmabuf ! kmssink > > The driver is tested with v4l2-compliance. > > Result on SM8550: > > v4l2-compliance --stream-from /media/FVDO_Freeway_720p.264 -s250 > > v4l2-compliance 1.29.0-5273, 64 bits, 64-bit time_t > v4l2-compliance SHA: 0ed98432fe68 2024-11-13 12:54:45 > > Compliance test for iris_driver device /dev/video0: > > Driver Info: > Driver name : iris_driver > Card type : iris_decoder > Bus info : platform:aa00000.video-codec > Driver version : 6.12.0 > Capabilities : 0x84204000 > Video Memory-to-Memory Multiplanar > Streaming > Extended Pix Format > Device Capabilities > Device Caps : 0x04204000 > Video Memory-to-Memory Multiplanar > Streaming > Extended Pix Format > Detected Stateful Decoder > > Required ioctls: > test VIDIOC_QUERYCAP: OK > test invalid ioctls: OK > > Allow for multiple opens: > test second /dev/video0 open: OK > test VIDIOC_QUERYCAP: OK > test VIDIOC_G/S_PRIORITY: OK > test for unlimited opens: OK > > Debug ioctls: > test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported) > test VIDIOC_LOG_STATUS: OK (Not Supported) > > Input ioctls: > test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) > test VIDIOC_ENUMAUDIO: OK (Not Supported) > test VIDIOC_G/S/ENUMINPUT: OK (Not Supported) > test VIDIOC_G/S_AUDIO: OK (Not Supported) > Inputs: 0 Audio Inputs: 0 Tuners: 0 > > Output ioctls: > test VIDIOC_G/S_MODULATOR: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_ENUMAUDOUT: OK (Not Supported) > test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) > test VIDIOC_G/S_AUDOUT: OK (Not Supported) > Outputs: 0 Audio Outputs: 0 Modulators: 0 > > Input/Output configuration ioctls: > test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) > test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) > test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) > test VIDIOC_G/S_EDID: OK (Not Supported) > > Control ioctls: > test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK > test VIDIOC_QUERYCTRL: OK > test VIDIOC_G/S_CTRL: OK > test VIDIOC_G/S/TRY_EXT_CTRLS: OK > test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK > test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) > Standard Controls: 5 Private Controls: 0 > > Format ioctls: > test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK > test VIDIOC_G/S_PARM: OK (Not Supported) > test VIDIOC_G_FBUF: OK (Not Supported) > test VIDIOC_G_FMT: OK > test VIDIOC_TRY_FMT: OK > test VIDIOC_S_FMT: OK > test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) > test Cropping: OK > test Composing: OK > test Scaling: OK (Not Supported) > > Codec ioctls: > test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) > test VIDIOC_G_ENC_INDEX: OK (Not Supported) > test VIDIOC_(TRY_)DECODER_CMD: OK > > Buffer ioctls: > test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK > test CREATE_BUFS maximum buffers: OK > test VIDIOC_REMOVE_BUFS: OK > test VIDIOC_EXPBUF: OK > test Requests: OK (Not Supported) > test blocking wait: OK > > Test input 0: > > Streaming ioctls: > test read/write: OK (Not Supported) > test MMAP (select, REQBUFS): OK > test MMAP (epoll, REQBUFS): OK > test MMAP (select, CREATE_BUFS): OK > test MMAP (epoll, CREATE_BUFS): OK > test USERPTR (select): OK (Not Supported) > test DMABUF: Cannot test, specify --expbuf-device > > Total for iris_driver device /dev/video0: 54, Succeeded: 54, Failed: 0, > Warnings: 0 > > Result on SM8250: > > v4l2-compliance --stream-from /media/FVDO_Freeway_720p.264 -s250 > > v4l2-compliance 1.29.0-5273, 64 bits, 64-bit time_t > v4l2-compliance SHA: 0ed98432fe68 2024-11-13 12:54:45 > > Compliance test for iris_driver device /dev/video0: > > Driver Info: > Driver name : iris_driver > Card type : iris_decoder > Bus info : platform:aa00000.video-codec > Driver version : 6.12.0 > Capabilities : 0x84204000 > Video Memory-to-Memory Multiplanar > Streaming > Extended Pix Format > Device Capabilities > Device Caps : 0x04204000 > Video Memory-to-Memory Multiplanar > Streaming > Extended Pix Format > Detected Stateful Decoder > > Required ioctls: > test VIDIOC_QUERYCAP: OK > test invalid ioctls: OK > > Allow for multiple opens: > test second /dev/video0 open: OK > test VIDIOC_QUERYCAP: OK > test VIDIOC_G/S_PRIORITY: OK > test for unlimited opens: OK > > Debug ioctls: > test VIDIOC_DBG_G/S_REGISTER: OK (Not Supported) > test VIDIOC_LOG_STATUS: OK (Not Supported) > > Input ioctls: > test VIDIOC_G/S_TUNER/ENUM_FREQ_BANDS: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_S_HW_FREQ_SEEK: OK (Not Supported) > test VIDIOC_ENUMAUDIO: OK (Not Supported) > test VIDIOC_G/S/ENUMINPUT: OK (Not Supported) > test VIDIOC_G/S_AUDIO: OK (Not Supported) > Inputs: 0 Audio Inputs: 0 Tuners: 0 > > Output ioctls: > test VIDIOC_G/S_MODULATOR: OK (Not Supported) > test VIDIOC_G/S_FREQUENCY: OK (Not Supported) > test VIDIOC_ENUMAUDOUT: OK (Not Supported) > test VIDIOC_G/S/ENUMOUTPUT: OK (Not Supported) > test VIDIOC_G/S_AUDOUT: OK (Not Supported) > Outputs: 0 Audio Outputs: 0 Modulators: 0 > > Input/Output configuration ioctls: > test VIDIOC_ENUM/G/S/QUERY_STD: OK (Not Supported) > test VIDIOC_ENUM/G/S/QUERY_DV_TIMINGS: OK (Not Supported) > test VIDIOC_DV_TIMINGS_CAP: OK (Not Supported) > test VIDIOC_G/S_EDID: OK (Not Supported) > > Control ioctls: > test VIDIOC_QUERY_EXT_CTRL/QUERYMENU: OK > test VIDIOC_QUERYCTRL: OK > test VIDIOC_G/S_CTRL: OK > test VIDIOC_G/S/TRY_EXT_CTRLS: OK > test VIDIOC_(UN)SUBSCRIBE_EVENT/DQEVENT: OK > test VIDIOC_G/S_JPEGCOMP: OK (Not Supported) > Standard Controls: 5 Private Controls: 0 > > Format ioctls: > test VIDIOC_ENUM_FMT/FRAMESIZES/FRAMEINTERVALS: OK > test VIDIOC_G/S_PARM: OK (Not Supported) > test VIDIOC_G_FBUF: OK (Not Supported) > test VIDIOC_G_FMT: OK > test VIDIOC_TRY_FMT: OK > test VIDIOC_S_FMT: OK > test VIDIOC_G_SLICED_VBI_CAP: OK (Not Supported) > test Cropping: OK > test Composing: OK > test Scaling: OK (Not Supported) > > Codec ioctls: > test VIDIOC_(TRY_)ENCODER_CMD: OK (Not Supported) > test VIDIOC_G_ENC_INDEX: OK (Not Supported) > test VIDIOC_(TRY_)DECODER_CMD: OK > > Buffer ioctls: > test VIDIOC_REQBUFS/CREATE_BUFS/QUERYBUF: OK > test CREATE_BUFS maximum buffers: OK > test VIDIOC_REMOVE_BUFS: OK > test VIDIOC_EXPBUF: OK > test Requests: OK (Not Supported) > test blocking wait: OK > > Test input 0: > > Streaming ioctls: > test read/write: OK (Not Supported) > test MMAP (select, REQBUFS): OK > test MMAP (epoll, REQBUFS): OK > test MMAP (select, CREATE_BUFS): OK > test MMAP (epoll, CREATE_BUFS): OK > test USERPTR (select): OK (Not Supported) > test DMABUF: Cannot test, specify --expbuf-device > > Total for iris_driver device /dev/video0: 54, Succeeded: 54, Failed: 0, > Warnings: 0 > > The result of fluster test on SM8550: > > 77/135 while testing JVT-AVC_V1 with > GStreamer-H.264-V4L2-Gst1.0.JVT-AVC_V1. > The failing tests are: > - 52 test vectors failed due to interlaced clips: Interlaced decoding is > not supported in iris driver. > Test Vectors: > cabac_mot_fld0_full > cabac_mot_mbaff0_full > cabac_mot_picaff0_full > CABREF3_Sand_D > CAFI1_SVA_C > CAMA1_Sony_C > CAMA1_TOSHIBA_B > cama1_vtc_c > cama2_vtc_b > CAMA3_Sand_E > cama3_vtc_b > CAMACI3_Sony_C > CAMANL1_TOSHIBA_B > CAMANL2_TOSHIBA_B > CAMANL3_Sand_E > CAMASL3_Sony_B > CAMP_MOT_MBAFF_L30 > CAMP_MOT_MBAFF_L31 > CANLMA2_Sony_C > CANLMA3_Sony_C > CAPA1_TOSHIBA_B > CAPAMA3_Sand_F > cavlc_mot_fld0_full_B > cavlc_mot_mbaff0_full_B > cavlc_mot_picaff0_full_B > CVCANLMA2_Sony_C > CVFI1_Sony_D > CVFI1_SVA_C > CVFI2_Sony_H > CVFI2_SVA_C > CVMA1_Sony_D > CVMA1_TOSHIBA_B > CVMANL1_TOSHIBA_B > CVMANL2_TOSHIBA_B > CVMAPAQP3_Sony_E > CVMAQP2_Sony_G > CVMAQP3_Sony_D > CVMP_MOT_FLD_L30_B > CVNLFI1_Sony_C > CVNLFI2_Sony_H > CVPA1_TOSHIBA_B > FI1_Sony_E > MR6_BT_B > MR7_BT_B > MR8_BT_B > MR9_BT_B > Sharp_MP_Field_1_B > Sharp_MP_Field_2_B > Sharp_MP_Field_3_B > Sharp_MP_PAFF_1r2 > Sharp_MP_PAFF_2r > CVMP_MOT_FRM_L31_B > - 3 test vectors failed due to unsupported bitstream. > num_slice_group_minus1 greater than zero is not supported by the > hardware. > Test Vectors: > FM1_BT_B > FM1_FT_E > FM2_SVA_C > - 2 test vectors failed because SP_SLICE type is not supported by the > hardware. > Test Vectors: > SP1_BT_A > sp2_bt_b > - 1 test vector failed due to unsupported profile: > V4L2_MPEG_VIDEO_H264_PROFILE_EXTENDED is being deprecated from sm8550 > onwards due to hardware issues. > Test Vectors: > BA3_SVA_C > > 23/69 while testing JVT-FR-EXT with > GStreamer-H.264-V4L2-Gst1.0.JVT-AVC_V1. > The failing tests are: > - 21 test vectors failed due to interlaced clips: Interlaced decoding is > not supported in iris driver. > Test Vectors: > brcm_freh4 > brcm_freh5 > brcm_freh6 > brcm_freh10 > brcm_freh11 > freh7_b > FREXT01_JVC_D > FREXT02_JVC_C > FRExt2_Panasonic_C > FRExt4_Panasonic_B > HCAFF1_HHI_B > HCAMFF1_HHI_B > HCHP3_HHI_A > HPCAFL_BRCM_C > HPCAFLNL_BRCM_C > HVLCFI0_Sony_B > HVLCMFF0_Sony_B > HVLCPFF0_Sony_B > HPCAMAPALQ_BRCM_B > HPCVFL_BRCM_A > HPCVFLNL_BRCM_A > - 2 test vectors failed due to 10bit bitstream: 10bit decoding is not > supported in iris driver > Test Vectors: > FREH10-1 > FREH10-2 > - 21 test vectors failed due to unsupported profile: > V4L2_MPEG_VIDEO_H264_PROFILE_HIGH_422 is not supported by the > hardware. > Test Vectors: > FREXT1_TANDBERG_A > FREXT2_TANDBERG_A > FREXT3_TANDBERG_A > Hi422FR1_SONY_A > Hi422FR2_SONY_A > Hi422FR3_SONY_A > Hi422FR4_SONY_A > Hi422FR6_SONY_A > Hi422FR7_SONY_A > Hi422FR8_SONY_A > Hi422FR9_SONY_A > Hi422FR10_SONY_A > Hi422FR11_SONY_A > Hi422FR12_SONY_A > Hi422FR13_SONY_A > Hi422FR14_SONY_A > Hi422FR15_SONY_A > Hi422FREXT16_SONY_A > Hi422FREXT17_SONY_A > Hi422FREXT18_SONY_A > Hi422FREXT19_SONY_A > - 2 test vectors failed due to unsupported bitstream. > chroma_fmt_idc is equal to 0(monochrome) in the bitstream which is not > supported by the hardware. > Test Vectors: > HPCAMOLQ_BRCM_B > HPCVMOLQ_BRCM_B > > The result of fluster test on SM8250: > > 78/135 while testing JVT-AVC_V1 with > GStreamer-H.264-V4L2-Gst1.0.JVT-AVC_V1. > The failing tests are: > - 52 test vectors failed due to interlaced clips: Interlaced decoding is > not supported in iris driver. > Test Vectors: > cabac_mot_fld0_full > cabac_mot_mbaff0_full > cabac_mot_picaff0_full > CABREF3_Sand_D > CAFI1_SVA_C > CAMA1_Sony_C > CAMA1_TOSHIBA_B > cama1_vtc_c > cama2_vtc_b > CAMA3_Sand_E > cama3_vtc_b > CAMACI3_Sony_C > CAMANL1_TOSHIBA_B > CAMANL2_TOSHIBA_B > CAMANL3_Sand_E > CAMASL3_Sony_B > CAMP_MOT_MBAFF_L30 > CAMP_MOT_MBAFF_L31 > CANLMA2_Sony_C > CANLMA3_Sony_C > CAPA1_TOSHIBA_B > CAPAMA3_Sand_F > cavlc_mot_fld0_full_B > cavlc_mot_mbaff0_full_B > cavlc_mot_picaff0_full_B > CVCANLMA2_Sony_C > CVFI1_Sony_D > CVFI1_SVA_C > CVFI2_Sony_H > CVFI2_SVA_C > CVMA1_Sony_D > CVMA1_TOSHIBA_B > CVMANL1_TOSHIBA_B > CVMANL2_TOSHIBA_B > CVMAPAQP3_Sony_E > CVMAQP2_Sony_G > CVMAQP3_Sony_D > CVMP_MOT_FLD_L30_B > CVNLFI1_Sony_C > CVNLFI2_Sony_H > CVPA1_TOSHIBA_B > FI1_Sony_E > MR6_BT_B > MR7_BT_B > MR8_BT_B > MR9_BT_B > Sharp_MP_Field_1_B > Sharp_MP_Field_2_B > Sharp_MP_Field_3_B > Sharp_MP_PAFF_1r2 > Sharp_MP_PAFF_2r > CVMP_MOT_FRM_L31_B > - 3 test vectors failed due to unsupported bitstream. > num_slice_group_minus1 greater than zero is not supported by the > hardware. > Test Vectors: > FM1_BT_B > FM1_FT_E > FM2_SVA_C > - 2 test vectors failed because SP_SLICE type is not supported by the > hardware. > Test Vectors: > SP1_BT_A > sp2_bt_b > > 23/69 while testing JVT-FR-EXT with > GStreamer-H.264-V4L2-Gst1.0.JVT-AVC_V1. > The failing tests are: > - 21 test vectors failed due to interlaced clips: Interlaced decoding is > not supported in iris driver. > Test Vectors: > brcm_freh4 > brcm_freh5 > brcm_freh6 > brcm_freh10 > brcm_freh11 > freh7_b > FREXT01_JVC_D > FREXT02_JVC_C > FRExt2_Panasonic_C > FRExt4_Panasonic_B > HCAFF1_HHI_B > HCAMFF1_HHI_B > HCHP3_HHI_A > HPCAFL_BRCM_C > HPCAFLNL_BRCM_C > HVLCFI0_Sony_B > HVLCMFF0_Sony_B > HVLCPFF0_Sony_B > HPCAMAPALQ_BRCM_B > HPCVFL_BRCM_A > HPCVFLNL_BRCM_A > - 2 test vectors failed due to 10bit bitstream: 10bit decoding is not > supported in iris driver > Test Vectors: > FREH10-1 > FREH10-2 > - 21 test vectors failed due to unsupported profile: > V4L2_MPEG_VIDEO_H264_PROFILE_HIGH_422 is not supported by the > hardware. > Test Vectors: > FREXT1_TANDBERG_A > FREXT2_TANDBERG_A > FREXT3_TANDBERG_A > Hi422FR1_SONY_A > Hi422FR2_SONY_A > Hi422FR3_SONY_A > Hi422FR4_SONY_A > Hi422FR6_SONY_A > Hi422FR7_SONY_A > Hi422FR8_SONY_A > Hi422FR9_SONY_A > Hi422FR10_SONY_A > Hi422FR11_SONY_A > Hi422FR12_SONY_A > Hi422FR13_SONY_A > Hi422FR14_SONY_A > Hi422FR15_SONY_A > Hi422FREXT16_SONY_A > Hi422FREXT17_SONY_A > Hi422FREXT18_SONY_A > Hi422FREXT19_SONY_A > - 2 test vectors failed due to unsupported bitstream. > chroma_fmt_idc is equal to 0(monochrome) in the bitstream which is not > supported by the hardware. > Test Vectors: > HPCAMOLQ_BRCM_B > HPCVMOLQ_BRCM_B > > To: Vikash Garodia <quic_vgarodia@xxxxxxxxxxx> > To: Abhinav Kumar <quic_abhinavk@xxxxxxxxxxx> > To: Mauro Carvalho Chehab <mchehab@xxxxxxxxxx> > To: Rob Herring <robh@xxxxxxxxxx> > To: Krzysztof Kozlowski <krzk+dt@xxxxxxxxxx> > To: Conor Dooley <conor+dt@xxxxxxxxxx> > To: Philipp Zabel <p.zabel@xxxxxxxxxxxxxx> > Cc: Hans Verkuil <hverkuil@xxxxxxxxx> > Cc: Sebastian Fricke <sebastian.fricke@xxxxxxxxxxxxx> > Cc: Bryan O'Donoghue <bryan.odonoghue@xxxxxxxxxx> > Cc: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx> > Cc: Neil Armstrong <neil.armstrong@xxxxxxxxxx> > Cc: Nicolas Dufresne <nicolas@xxxxxxxxxxxx> > Cc: Uwe Kleine-König <u.kleine-koenig@xxxxxxxxxxxx> > Cc: Jianhua Lu <lujianhua000@xxxxxxxxx> > Cc: linux-media@xxxxxxxxxxxxxxx > Cc: linux-arm-msm@xxxxxxxxxxxxxxx > Cc: devicetree@xxxxxxxxxxxxxxx > Cc: linux-kernel@xxxxxxxxxxxxxxx > > Signed-off-by: Dikshita Agarwal <quic_dikshita@xxxxxxxxxxx> > --- > Dikshita Agarwal (18): > dt-bindings: media: Add video support for QCOM SM8550 SoC > media: iris: add platform driver for iris video device > media: iris: implement iris v4l2 file ops > media: iris: introduce iris core state management with shared queues > media: iris: implement video firmware load/unload > media: iris: implement boot sequence of the firmware > media: iris: introduce host firmware interface with necessary hooks > media: iris: implement power management > media: iris: implement reqbuf ioctl with vb2_queue_setup > media: iris: implement iris v4l2_ctrl_ops > media: iris: implement vb2 streaming ops > media: iris: allocate, initialize and queue internal buffers > media: iris: implement vb2 ops for buf_queue and firmware response > media: iris: add support for dynamic resolution change > media: iris: handle streamoff/on from client in dynamic resolution change > media: iris: add support for drain sequence > media: iris: enable video driver probe of SM8250 SoC > media: MAINTAINERS: add Qualcomm iris video accelerator driver > > Vedang Nagar (10): > media: iris: implement s_fmt, g_fmt and try_fmt ioctls > media: iris: implement g_selection ioctl > media: iris: implement enum_fmt and enum_framesizes ioctls > media: iris: implement subscribe_event and unsubscribe_event ioctls > media: iris: implement query_cap ioctl > media: iris: implement set properties to firmware during streamon > media: iris: subscribe parameters and properties to firmware for hfi_gen2 > media: iris: add check whether the video session is supported or not > media: iris: implement power scaling for vpu2 and vpu3 > media: iris: add check to allow sub states transitions > > .../bindings/media/qcom,sm8550-iris.yaml | 158 ++++ > MAINTAINERS | 10 + > drivers/media/platform/qcom/Kconfig | 1 + > drivers/media/platform/qcom/Makefile | 1 + > drivers/media/platform/qcom/iris/Kconfig | 13 + > drivers/media/platform/qcom/iris/Makefile | 27 + > drivers/media/platform/qcom/iris/iris_buffer.c | 624 ++++++++++++++ > drivers/media/platform/qcom/iris/iris_buffer.h | 117 +++ > drivers/media/platform/qcom/iris/iris_core.c | 96 +++ > drivers/media/platform/qcom/iris/iris_core.h | 111 +++ > drivers/media/platform/qcom/iris/iris_ctrls.c | 259 ++++++ > drivers/media/platform/qcom/iris/iris_ctrls.h | 22 + > drivers/media/platform/qcom/iris/iris_firmware.c | 110 +++ > drivers/media/platform/qcom/iris/iris_firmware.h | 15 + > drivers/media/platform/qcom/iris/iris_hfi_common.c | 176 ++++ > drivers/media/platform/qcom/iris/iris_hfi_common.h | 155 ++++ > drivers/media/platform/qcom/iris/iris_hfi_gen1.h | 16 + > .../platform/qcom/iris/iris_hfi_gen1_command.c | 826 ++++++++++++++++++ > .../platform/qcom/iris/iris_hfi_gen1_defines.h | 448 ++++++++++ > .../platform/qcom/iris/iris_hfi_gen1_response.c | 666 ++++++++++++++ > drivers/media/platform/qcom/iris/iris_hfi_gen2.h | 41 + > .../platform/qcom/iris/iris_hfi_gen2_command.c | 957 +++++++++++++++++++++ > .../platform/qcom/iris/iris_hfi_gen2_defines.h | 160 ++++ > .../platform/qcom/iris/iris_hfi_gen2_packet.c | 292 +++++++ > .../platform/qcom/iris/iris_hfi_gen2_packet.h | 125 +++ > .../platform/qcom/iris/iris_hfi_gen2_response.c | 931 ++++++++++++++++++++ > drivers/media/platform/qcom/iris/iris_hfi_queue.c | 314 +++++++ > drivers/media/platform/qcom/iris/iris_hfi_queue.h | 182 ++++ > drivers/media/platform/qcom/iris/iris_instance.h | 79 ++ > .../platform/qcom/iris/iris_platform_common.h | 186 ++++ > .../platform/qcom/iris/iris_platform_sm8250.c | 148 ++++ > .../platform/qcom/iris/iris_platform_sm8550.c | 265 ++++++ > drivers/media/platform/qcom/iris/iris_power.c | 140 +++ > drivers/media/platform/qcom/iris/iris_power.h | 13 + > drivers/media/platform/qcom/iris/iris_probe.c | 378 ++++++++ > drivers/media/platform/qcom/iris/iris_resources.c | 131 +++ > drivers/media/platform/qcom/iris/iris_resources.h | 18 + > drivers/media/platform/qcom/iris/iris_state.c | 276 ++++++ > drivers/media/platform/qcom/iris/iris_state.h | 144 ++++ > drivers/media/platform/qcom/iris/iris_utils.c | 90 ++ > drivers/media/platform/qcom/iris/iris_utils.h | 53 ++ > drivers/media/platform/qcom/iris/iris_vb2.c | 336 ++++++++ > drivers/media/platform/qcom/iris/iris_vb2.h | 19 + > drivers/media/platform/qcom/iris/iris_vdec.c | 662 ++++++++++++++ > drivers/media/platform/qcom/iris/iris_vdec.h | 25 + > drivers/media/platform/qcom/iris/iris_vidc.c | 455 ++++++++++ > drivers/media/platform/qcom/iris/iris_vidc.h | 15 + > drivers/media/platform/qcom/iris/iris_vpu2.c | 38 + > drivers/media/platform/qcom/iris/iris_vpu3.c | 122 +++ > drivers/media/platform/qcom/iris/iris_vpu_buffer.c | 270 ++++++ > drivers/media/platform/qcom/iris/iris_vpu_buffer.h | 91 ++ > drivers/media/platform/qcom/iris/iris_vpu_common.c | 369 ++++++++ > drivers/media/platform/qcom/iris/iris_vpu_common.h | 28 + > .../platform/qcom/iris/iris_vpu_register_defines.h | 17 + > 54 files changed, 11221 insertions(+) > --- > base-commit: 698b6e3163bafd61e1b7d13572e2c42974ac85ec > change-id: 20241028-qcom-video-iris-94d5a12e6d9e > > Best regards,
