Hi Stefan!
On Thu, 9 Apr 2015 00:12:55 +0200 (CEST), Stefan Wahren
<stefan.wahren@xxxxxxxx> wrote:
> Hi Harald,
>
> [ add devicetree mailinglist ]
>
>> Harald Geyer <harald@xxxxxxxxx> hat am 8. April 2015 um 19:45
>> geschrieben:
>>
>>
>> The imx23-olinuxino board has an i2c interface exposed on UEXT
connector.
>
> AFAIK the iMX233-OLinuXino-MICRO don't have a UEXT connector.
Yes, but I don't think having default i2c pins there would be a bad thing.
> Maybe we reached the point to make dts files for every Olinuxino board.
> In that case we could also handle the USB Host / Peripherial issue.
Yes, I'm thinking in this direction. But even if peripherial mode works
on micro/nano (which I haven't been able to confirm yet) that doesn't mean
that it should be set in the default device tree. After all Olimex
themself
advertise the port as host.
>> This patch provides the necessary devicetree code.
>> Tested with MOD-LCD1x9 from Olimex.
>>
>> This patch is based on work by Fadil Berisha with his permission.
However
>> all bugs are mine.
>>
>> Signed-off-by: Harald Geyer <harald@xxxxxxxxx>
>> ---
>> arch/arm/boot/dts/imx23-olinuxino.dts | 6 +++++
>> arch/arm/boot/dts/imx23.dtsi | 40 ++++++++++++++++++++++++++++++++-
>> 2 files changed, 45 insertions(+), 1 deletion(-)
>>
>> [...]
>> --- a/arch/arm/boot/dts/imx23.dtsi
>> +++ b/arch/arm/boot/dts/imx23.dtsi
>> @@ -308,6 +308,39 @@
>> fsl,voltage = <MXS_VOLTAGE_HIGH>;
>> fsl,pull-up = <MXS_PULL_ENABLE>;
>> };
>> +
>> + i2c_pins_a: i2c@0 {
>> + reg = <0>;
>> + fsl,pinmux-ids = <
>> + MX23_PAD_I2C_SCL__I2C_SCL
>> + MX23_PAD_I2C_SDA__I2C_SDA
>> + >;
>> + fsl,drive-strength = <MXS_DRIVE_8mA>;
>> + fsl,voltage = <MXS_VOLTAGE_HIGH>;
>> + fsl,pull-up = <MXS_PULL_ENABLE>;
>> + };
>> +
>> + i2c_pins_b: i2c@1 {
>> + reg = <1>;
>> + fsl,pinmux-ids = <
>> + MX23_PAD_LCD_ENABLE__I2C_SCL
>> + MX23_PAD_LCD_HSYNC__I2C_SDA
>> + >;
>> + fsl,drive-strength = <MXS_DRIVE_8mA>;
>> + fsl,voltage = <MXS_VOLTAGE_HIGH>;
>> + fsl,pull-up = <MXS_PULL_ENABLE>;
>> + };
>> +
>> + i2c_pins_c: i2c@2 {
>> + reg = <2>;
>> + fsl,pinmux-ids = <
>> + MX23_PAD_SSP1_DATA1__I2C_SCL
>> + MX23_PAD_SSP1_DATA2__I2C_SDA
>> + >;
>> + fsl,drive-strength = <MXS_DRIVE_8mA>;
>> + fsl,voltage = <MXS_VOLTAGE_HIGH>;
>> + fsl,pull-up = <MXS_PULL_ENABLE>;
>> + };
>
> Please add only i2c_pins_b because this pin muxing is the only used one.
I disagree: Having all possible i2c pin groups documented in devicetree is
a good thing. Also imx23.dtsi is more general then olinuxino - somebody
might produce a imx23 based board where one of the other pin groups makes
more sense to use. Well, even on olinuxino somebody might use i2c_pins_a
if they don't need an UART, but use an LCD.
Thanks,
Harald
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
