On Mon, 06 Apr 2015, Bjorn Andersson wrote:
> Add the regulator subnodes to the Qualcomm RPM MFD device tree bindings.
>
> Reviewed-by: Stephen Boyd <sboyd@xxxxxxxxxxxxxx>
> Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxxxxxx>
> ---
>
> Changes since v2:
> - s/notes/nodes from Stephen
>
> Documentation/devicetree/bindings/mfd/qcom-rpm.txt | 217 +++++++++++++++++++--
> 1 file changed, 205 insertions(+), 12 deletions(-)
Applied, thanks.
> diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
> index 85e3198..f7c22c5 100644
> --- a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
> +++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
> @@ -31,16 +31,6 @@ frequencies.
> Value type: <string-array>
> Definition: must be the three strings "ack", "err" and "wakeup", in order
>
> -- #address-cells:
> - Usage: required
> - Value type: <u32>
> - Definition: must be 1
> -
> -- #size-cells:
> - Usage: required
> - Value type: <u32>
> - Definition: must be 0
> -
> - qcom,ipc:
> Usage: required
> Value type: <prop-encoded-array>
> @@ -52,6 +42,188 @@ frequencies.
> - u32 representing the ipc bit within the register
>
>
> += SUBNODES
> +
> +The RPM exposes resources to its subnodes. The below bindings specify the set
> +of valid subnodes that can operate on these resources.
> +
> +== Regulators
> +
> +Regulator nodes are identified by their compatible:
> +
> +- compatible:
> + Usage: required
> + Value type: <string>
> + Definition: must be one of:
> + "qcom,rpm-pm8058-regulators"
> + "qcom,rpm-pm8901-regulators"
> + "qcom,rpm-pm8921-regulators"
> +
> +- vdd_l0_l1_lvs-supply:
> +- vdd_l2_l11_l12-supply:
> +- vdd_l3_l4_l5-supply:
> +- vdd_l6_l7-supply:
> +- vdd_l8-supply:
> +- vdd_l9-supply:
> +- vdd_l10-supply:
> +- vdd_l13_l16-supply:
> +- vdd_l14_l15-supply:
> +- vdd_l17_l18-supply:
> +- vdd_l19_l20-supply:
> +- vdd_l21-supply:
> +- vdd_l22-supply:
> +- vdd_l23_l24_l25-supply:
> +- vdd_ncp-supply:
> +- vdd_s0-supply:
> +- vdd_s1-supply:
> +- vdd_s2-supply:
> +- vdd_s3-supply:
> +- vdd_s4-supply:
> + Usage: optional (pm8058 only)
> + Value type: <phandle>
> + Definition: reference to regulator supplying the input pin, as
> + described in the data sheet
> +
> +- lvs0_in-supply:
> +- lvs1_in-supply:
> +- lvs2_in-supply:
> +- lvs3_in-supply:
> +- mvs_in-supply:
> +- vdd_l0-supply:
> +- vdd_l1-supply:
> +- vdd_l2-supply:
> +- vdd_l3-supply:
> +- vdd_l4-supply:
> +- vdd_l5-supply:
> +- vdd_l6-supply:
> +- vdd_s0-supply:
> +- vdd_s1-supply:
> +- vdd_s2-supply:
> +- vdd_s3-supply:
> +- vdd_s4-supply:
> + Usage: optional (pm8901 only)
> + Value type: <phandle>
> + Definition: reference to regulator supplying the input pin, as
> + described in the data sheet
> +
> +- vdd_l1_l2_l12_l18-supply:
> +- vdd_l3_l15_l17-supply:
> +- vdd_l4_l14-supply:
> +- vdd_l5_l8_l16-supply:
> +- vdd_l6_l7-supply:
> +- vdd_l9_l11-supply:
> +- vdd_l10_l22-supply:
> +- vdd_l21_l23_l29-supply:
> +- vdd_l24-supply:
> +- vdd_l25-supply:
> +- vdd_l26-supply:
> +- vdd_l27-supply:
> +- vdd_l28-supply:
> +- vdd_ncp-supply:
> +- vdd_s1-supply:
> +- vdd_s2-supply:
> +- vdd_s4-supply:
> +- vdd_s5-supply:
> +- vdd_s6-supply:
> +- vdd_s7-supply:
> +- vdd_s8-supply:
> +- vin_5vs-supply:
> +- vin_lvs1_3_6-supply:
> +- vin_lvs2-supply:
> +- vin_lvs4_5_7-supply:
> + Usage: optional (pm8921 only)
> + Value type: <phandle>
> + Definition: reference to regulator supplying the input pin, as
> + described in the data sheet
> +
> +The regulator node houses sub-nodes for each regulator within the device. Each
> +sub-node is identified using the node's name, with valid values listed for each
> +of the pmics below.
> +
> +pm8058:
> + l0, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13, l14, l15,
> + l16, l17, l18, l19, l20, l21, l22, l23, l24, l25, s0, s1, s2, s3, s4,
> + lvs0, lvs1, ncp
> +
> +pm8901:
> + l0, l1, l2, l3, l4, l5, l6, s0, s1, s2, s3, s4, lvs0, lvs1, lvs2, lvs3,
> + mvs
> +
> +pm8921:
> + s1, s2, s3, s4, s7, s8, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
> + l12, l14, l15, l16, l17, l18, l21, l22, l23, l24, l25, l26, l27, l28,
> + l29, lvs1, lvs2, lvs3, lvs4, lvs5, lvs6, lvs7, usb-switch, hdmi-switch,
> + ncp
> +
> +The content of each sub-node is defined by the standard binding for regulators -
> +see regulator.txt - with additional custom properties described below:
> +
> +=== Switch-mode Power Supply regulator custom properties
> +
> +- bias-pull-down:
> + Usage: optional
> + Value type: <empty>
> + Definition: enable pull down of the regulator when inactive
> +
> +- qcom,switch-mode-frequency:
> + Usage: required
> + Value type: <u32>
> + Definition: Frequency (Hz) of the switch-mode power supply;
> + must be one of:
> + 19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
> + 2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
> + 1480000, 1370000, 1280000, 1200000
> +
> +- qcom,force-mode:
> + Usage: optional (default if no other qcom,force-mode is specified)
> + Value type: <u32>
> + Defintion: indicates that the regulator should be forced to a
> + particular mode, valid values are:
> + QCOM_RPM_FORCE_MODE_NONE - do not force any mode
> + QCOM_RPM_FORCE_MODE_LPM - force into low power mode
> + QCOM_RPM_FORCE_MODE_HPM - force into high power mode
> + QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically
> + select its own mode based on
> + realtime current draw, only for:
> + pm8921 smps and ftsmps
> +
> +- qcom,power-mode-hysteretic:
> + Usage: optional
> + Value type: <empty>
> + Definition: select that the power supply should operate in hysteretic
> + mode, instead of the default pwm mode
> +
> +=== Low-dropout regulator custom properties
> +
> +- bias-pull-down:
> + Usage: optional
> + Value type: <empty>
> + Definition: enable pull down of the regulator when inactive
> +
> +- qcom,force-mode:
> + Usage: optional
> + Value type: <u32>
> + Defintion: indicates that the regulator should not be forced to any
> + particular mode, valid values are:
> + QCOM_RPM_FORCE_MODE_NONE - do not force any mode
> + QCOM_RPM_FORCE_MODE_LPM - force into low power mode
> + QCOM_RPM_FORCE_MODE_HPM - force into high power mode
> + QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass
> + mode, i.e. to act as a switch
> + and not regulate, only for:
> + pm8921 pldo, nldo and nldo1200
> +
> +=== Negative Charge Pump custom properties
> +
> +- qcom,switch-mode-frequency:
> + Usage: required
> + Value type: <u32>
> + Definition: Frequency (Hz) of the swith mode power supply;
> + must be one of:
> + 19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
> + 2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
> + 1480000, 1370000, 1280000, 1200000
> +
> = EXAMPLE
>
> #include <dt-bindings/mfd/qcom-rpm.h>
> @@ -64,7 +236,28 @@ frequencies.
> interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
> interrupt-names = "ack", "err", "wakeup";
>
> - #address-cells = <1>;
> - #size-cells = <0>;
> + regulators {
> + compatible = "qcom,rpm-pm8921-regulators";
> + vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
> +
> + s1 {
> + regulator-min-microvolt = <1225000>;
> + regulator-max-microvolt = <1225000>;
> +
> + bias-pull-down;
> +
> + qcom,switch-mode-frequency = <3200000>;
> + };
> +
> + pm8921_s4: s4 {
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> +
> + qcom,switch-mode-frequency = <1600000>;
> + bias-pull-down;
> +
> + qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
> + };
> + };
> };
>
--
Lee Jones
Linaro STMicroelectronics Landing Team Lead
Linaro.org │ Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
