On 14/11/2024 14:03, Ciprian Hegbeli wrote: > The ADF4382A is a high performance, ultralow jitter, Frac-N PLL > with integrated VCO ideally suited for LO generation for 5G applications > or data converter clock applications. The high performance > PLL has a figure of merit of -239 dBc/Hz, low 1/f Noise and > high PFD frequency of 625MHz in integer mode that can achieve > ultralow in-band noise and integrated jitter. The ADF4382A can > generate frequencies in a fundamental octave range of 11.5 GHz to > 21 GHz, thereby eliminating the need for sub-harmonic filters. The > divide by 2 and 4 output dividers on the part allow frequencies to > be generated from 5.75GHz to 10.5GHz and 2.875GHz to 5.25GHz > respectively. > > Signed-off-by: Ciprian Hegbeli <ciprian.hegbeli@xxxxxxxxxx> > --- > .../bindings/iio/frequency/adi,adf4382.yaml | 141 ++++++++++++++++++ > 1 file changed, 141 insertions(+) > create mode 100644 Documentation/devicetree/bindings/iio/frequency/adi,adf4382.yaml > > diff --git a/Documentation/devicetree/bindings/iio/frequency/adi,adf4382.yaml b/Documentation/devicetree/bindings/iio/frequency/adi,adf4382.yaml > new file mode 100644 > index 000000000000..44a29ac7a2e8 > --- /dev/null > +++ b/Documentation/devicetree/bindings/iio/frequency/adi,adf4382.yaml > @@ -0,0 +1,141 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/iio/frequency/adi,adf4382.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: ADF4382 Microwave Wideband Synthesizer with Integrated VCO > + > +maintainers: > + - Antoniu Miclaus <antoniu.miclaus@xxxxxxxxxx> > + - Ciprian Hegbeli <ciprian.hegbeli@xxxxxxxxxx> > + > +description: The ADF4382 is a high performance, ultralow jitter, Frac-N PLL with > + integrated VCO ideally suited for LO generation for 5G applications > + or data converter clock applications. > + > + https://www.analog.com/en/products/adf4382a.html > + > +properties: > + compatible: > + enum: > + - adi,adf4382 > + - adi,adf4382a > + > + reg: > + maxItems: 1 > + > + spi-max-frequency: > + maximum: 75000000 > + > + clocks: > + description: Clock to provide CLKIN reference clock signal. > + maxItems: 1 > + > + clock-names: > + description: > + External clock that provides reference input frequency. > + items: > + - const: ref_clk > + > + '#clock-cells': > + const: 0 > + > + clock-output-names: > + maxItems: 1 > + > + adi,charge-pump-microamp: > + description: These lines are a bit over 80 chars, maybe you could rearrange them. > + The charge pump current that the external loop filter was designed for. > + If this property is not specified, then the charge pump current is set to the > + default 11100uA. The valid values are listed below. However, if the set value is > + not supported, the driver will look for the closest valid charge pump current. > + anyOf: > + - enum: [790, 990, 1190, 1380, 1590, 1980, 2390, 2790, 3180, 3970, 4770, 5570, 6330, 7910, 9510, 11100] > + > + adi,ref-divider: > + description: > + Input divider of the reference frequency, cannot be lower then 1 or > + higher then 63. > + allOf: > + - $ref: /schemas/types.yaml#/definitions/uint32 > + - minimum: 1 > + - maximum: 63 > + - default: 1 > + maxItems: 1 > + > + adi,ref-doubler-enable: > + description: > + Enables the doubling of the reference clock. > + type: boolean > + maxItems: 1 > + > + adi,bleed-word: > + description: > + A small programmable constant charge pump current, known as bleed current, > + can be used to optimize the phase noise and fractional spurious signals > + in fractional mode. > + allOf: > + - $ref: /schemas/types.yaml#/definitions/uint32 > + - minimum: 0 > + - maximum: 4095 > + - default: 0 > + maxItems: 1 > + > + adi,power-up-frequency: > + description: > + PLL tunes to the set frequency on probe or defaults to 2,305 GHz. > + allOf: > + - $ref: /schemas/types.yaml#/definitions/uint64 > + - minimum: 687500000 > + - maximum: 22000000000 > + - default: 2305000000 > + maxItems: 1 > + > + adi,output-power-value: > + description: > + The output power amplitude level which will be applied for both channels > + at startup. > + allOf: > + - $ref: /schemas/types.yaml#/definitions/uint32 > + - minimum: 0 > + - maximum: 15 > + - default: 11 > + maxItems: 1 > + > + adi,spi-3wire-enable: > + description: > + Uses SPI in 3 wire mode, by default is uses 4 wire mode. > + type: boolean > + maxItems: 1 > + > + adi,cmos-3v3: > + description: > + Sets the SPI logic to 3.3V, by defautl it uses 1,8V. > + type: boolean > + maxItems: 1 > + > +required: > + - compatible > + - reg > + - clocks > + - clock-names > + > +additionalProperties: false > + > +examples: > + - | > + spi { > + #address-cells = <1>; > + #size-cells = <0>; > + frequency@0 { > + compatible = "adi,adf4382"; > + reg = <0>; > + spi-max-frequency = <1000000>; > + clocks = <&adf4382_clkin>; > + clock-names = "ref_clk"; Should it not be adi,charge-pump-microamp instead? dt_binding_check complains about this. > + adi,charge-pump-current = <15>; > + adi,ref-divider = <1>; > + }; > + }; > +... Best regards, Javier Carrasco
