On Tue, Nov 12, 2024 at 07:49:18PM +0100, barnabas.czeman@xxxxxxxxxxxxxx wrote:
> On 2024-11-12 18:27, Stephan Gerhold wrote:
> > On Tue, Nov 12, 2024 at 04:49:38PM +0100, Barnabás Czémán wrote:
> > > From: Otto Pflüger <otto.pflueger@xxxxxxxxx>
> > >
> > > Add initial support for MSM8917 SoC.
> > >
> > > Signed-off-by: Otto Pflüger <otto.pflueger@xxxxxxxxx>
> > > [reword commit, rebase, fix schema errors]
> > > Signed-off-by: Barnabás Czémán <barnabas.czeman@xxxxxxxxxxxxxx>
> > > ---
> > > arch/arm64/boot/dts/qcom/msm8917.dtsi | 1974
> > > +++++++++++++++++++++++++++++++++
> > > 1 file changed, 1974 insertions(+)
> > >
> > > diff --git a/arch/arm64/boot/dts/qcom/msm8917.dtsi
> > > b/arch/arm64/boot/dts/qcom/msm8917.dtsi
> > > new file mode 100644
> > > index 0000000000000000000000000000000000000000..cf0a0eec1141e11faca0ee9705d6348ab32a0f50
> > > --- /dev/null
> > > +++ b/arch/arm64/boot/dts/qcom/msm8917.dtsi
> > > @@ -0,0 +1,1974 @@
> > > [...]
> > > + domain-idle-states {
> > > + cluster_sleep_0: cluster-sleep-0 {
> > > + compatible = "domain-idle-state";
> > > + arm,psci-suspend-param = <0x41000023>;
> > > + entry-latency-us = <700>;
> > > + exit-latency-us = <650>;
> > > + min-residency-us = <1972>;
> > > + };
> > > +
> > > + cluster_sleep_1: cluster-sleep-1 {
> > > + compatible = "domain-idle-state";
> > > + arm,psci-suspend-param = <0x41000043>;
> > > + entry-latency-us = <240>;
> > > + exit-latency-us = <280>;
> > > + min-residency-us = <806>;
> > > + };
> >
> > I think my comment here is still open:
> >
> > This is strange, the deeper sleep state has lower timings than the
> > previous one?
> I was reordering based on Konrad comments when i have renamed the nodes
> maybe it is not correct then.
> I am searching for how to validate these levels, i have find these
> https://git.codelinaro.org/clo/la/kernel/msm-4.9/-/blob/LA.UM.10.6.2.c26-01500-89xx.0/arch/arm64/boot/dts/qcom/msm8917-pm.dtsi#L45-91
I think you translated them correctly. It feels like downstream is weird
or even wrong here. Usually a higher psci-mode (retention = 2, gdhs = 4)
also implies a deeper idle state. But at some point the
perf-l2-retention and perf-l2-gdhs state were swapped downstream:
https://git.codelinaro.org/clo/la/kernel/msm-3.18/-/commit/dea262a17a9e80dacb86b7c2f269bcc7b4df3a13
I don't know if this is intended or just an oversight. If no one can
clarify why this change was done I guess we can just choose between the
following two options:
1. Describe it exactly like it was done downstream. In that case I
would suggest swapping the node order back to what you had in v1.
Even if that means that a lower idle state has the higher psci-mode
(arm,psci-suspend-param). That should match what downstream did.
OR
2. Omit cluster-sleep-0 and cluster-sleep-1. I doubt anyone will notice
the minor difference in power consumption. The most important idle
state is the deepest "power collapse" (PC) state.
@Konrad: Do you have any opinion here?
> Do you know where can i find psci-suspend-param-s?
You need to translate it like in this code here:
https://git.codelinaro.org/clo/la/kernel/msm-4.9/-/blob/LA.UM.10.6.2.c26-01500-89xx.0/drivers/cpuidle/lpm-levels.c#L1337-1340
Roughly described:
- Set BIT(30) if the CPU state has qcom,is-reset
- Affinity level is the hierarchy level that goes idle.
In your case: CPU = 0, L2 cache/cluster = 1.
Shift that to bit 24 (1 << 24 for cache/cluster)
- For the state itself you need to combine the qcom,psci-cpu-mode and
qcom,psci-mode according to the qcom,psci-mode-shift.
E.g. for the "perf-l2-pc" state, combined with the deepest CPU state
("pc"):
- BIT(30) is set because of qcom,is-reset
- (1 << 24) because it's a L2 cache/cluster idle state
- (qcom,psci-cpu-mode = <3>) << (qcom,psci-mode-shift = <0>) = (3 << 0)
- (qcom,psci-mode = <5>) << (qcom,psci-mode-shift = <4>) = (5 << 4)
All that combined: BIT(30) | (1 << 24) | (3 << 0) | (5 << 4)
= 0x41000053
Which is what you have for cluster-sleep-2. The ones you have look
correct to me. :-)
> Should I also add wfi level?
I think we usually omit those for the CPU at least. Not sure about the
cache/cluster one. As I mentioned, at the end the most important idle
state to have is the deepest ones. Those will get used during suspend
and when you don't use the device. The others are more minor
optimization for light usage, which will be less noticeable.
Thanks,
Stephan
